Modeling of Piezoelectric Energy Harvesting from an L-shaped Beam-mass Structure with an Application to UAVs

2008 ◽  
Vol 20 (5) ◽  
pp. 529-544 ◽  
Author(s):  
Alper Erturk ◽  
Jamil M. Renno ◽  
Daniel J. Inman
Keyword(s):  
Energy Harvesting ◽  
Energy Harvester ◽  
Electrical Power ◽  
Distributed Parameter ◽  
Voltage Response ◽  
Shaped Beam ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Distributed Parameter Model

Cantilevered piezoelectric energy harvesters have been extensively investigated in the literature of energy harvesting. As an alternative to conventional cantilevered beams, this article presents the L-shaped beam-mass structure as a new piezoelectric energy harvester configuration. This structure can be tuned to have the first two natural frequencies relatively close to each other, resulting in the possibility of a broader band energy harvesting system. This article describes the important features of the L-shaped piezoelectric energy harvester configuration and develops a linear distributed parameter model for predicting the electromechanically coupled voltage response and displacement response of the harvester structure. After deriving the coupled distributed parameter model, a case study is presented to investigate the electrical power generation performance of the L-shaped energy harvester. A direct application of the L-shaped piezoelectric energy harvester configuration is proposed for use as landing gears in unmanned air vehicle applications and a case study is presented where the results of the L-shaped — energy harvester — landing gear are favorably compared against the published experimental results of a curved beam configuration used for the same purpose.

scholarly journals Recent Trend in Biomechanical Energy Harvesting

10.48175/606 ◽  
2020 ◽  
pp. 68-73
Author(s):  
Swapnil Arawade ◽  
Ganesh Korwar
Keyword(s):  
Energy Harvesting ◽  
Energy Harvester ◽  
Recent Trend ◽  
Electrical Power ◽  
Energy Crisis ◽  
Smart Devices ◽  
Energy Harvesters ◽  
The Past ◽  
Innovative Work ◽  
Work Done

In this literature different biomechanical energy harvesters are reviewed. In the past years a lot of work reported on energy harvesting. Energy crisis is the main issue in front of human so it is essential to find new promising ways to fulfil the need of electricity. Wearable smart devices and small sensor require low electrical power so to power them biomechanical energy harvesters comes into picture. The innovative work done by the researchers in developing new biomechanical energy harvester is discussed and summarized.

On Mathematical Modeling of Piezoelectric Energy Harvesters

2014 ◽  
Vol 953-954 ◽  
pp. 655-658 ◽  
Author(s):  
Guang Qing Shang ◽  
Hong Bing Wang ◽  
Chun Hua Sun
Keyword(s):  
Mathematical Modeling ◽  
Energy Harvesting ◽  
Energy Harvester ◽  
Vibration Energy ◽  
Piezoelectric Energy Harvesting ◽  
Vibration Energy Harvester ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Energy Harvesting System ◽  
Piezoelectric Vibration

Energy harvesting system has become one of important areas of ​​research and develops rapidly. How to improve the performance of the piezoelectric vibration energy harvester is a key issue in engineering applications. There are many literature on piezoelectric energy harvesting. The paper places focus on summarizing these literature of mathematical modeling of piezoelectric energy harvesting, ranging from the linear to nonlinear, from early a single mechanical degree to piezoaeroelastic problems.

scholarly journals A Curve-Shaped Beam Bistable Piezoelectric Energy Harvester with Variable Potential Well: Modeling and Numerical Simulation

Micromachines ◽  
2021 ◽  
Vol 12 (8) ◽  
pp. 995
Author(s):  
Xiaoyu Chen ◽  
Xuhui Zhang ◽  
Luyang Chen ◽  
Yan Guo ◽  
Fulin Zhu
Keyword(s):  
Energy Harvesting ◽  
Energy Harvester ◽  
Dynamic Responses ◽  
Force Model ◽  
Potential Well ◽  
Shaped Beam ◽  
Piezoelectric Energy ◽  
Straight Beam ◽  
Wide Range ◽  
Variable Potential

To improve the energy harvesting performance of an energy harvester, a novel bistable piezoelectric energy harvester with variable potential well (BPEH-V) is proposed by introducing a spring to the external magnet from a curve-shaped beam bistable harvester (CBH-C). First, finite element simulation was performed in COMSOL software to validate that the curved beam configuration was superior to the straight beam in power generation performance, which benefits energy harvesting. Moreover, the nonlinear magnetic model was obtained by using the magnetic dipoles method, and the nonlinear restoring force model of the curve-shaped beam was acquired based on fitting the experimental data. The corresponding coupled governing equations were derived by using generalized Hamilton’s principle, the dynamic responses were obtained by solving the coupling equations with the ode45 method. Finally, the numerical simulations showed that the proposed harvester can make interwell oscillations easier due to the spring being efficiently introduced to pull down the potential barrier compared with the conventional bistable harvester. Spring stiffness has a great impact on characteristics of the system, and a suitable stiffness contributes to realize large-amplitude interwell oscillations over a wide range of excitation, especially in the low excitation condition.

Electroelastic Finite Element Modeling and Experimental Validation of Structurally-Integrated Piezoelectric Energy Harvester

2013 ◽  
Author(s):  
Ugur Aridogan ◽  
Ipek Basdogan ◽  
Alper Erturk
Keyword(s):  
Finite Element ◽  
Energy Harvesting ◽  
Energy Harvester ◽  
Electrical Power ◽  
Element Model ◽  
Thin Plates ◽  
Flexible Plate ◽  
Numerical Predictions ◽  
Piezoelectric Energy ◽  
Host Structure

Vibration-based energy harvesting has attracted interest of researchers from various disciplines over the past decade. In the literature of piezoelectric energy harvesting, the typical configuration is a unimorph or a bimorph cantilevered piezoelectric beam located on a vibrating host structure subjected to base excitations. As an alternative to cantilevered piezoelectric beams, piezoelectric layers structurally integrated on thin plates can be used as vibration-based energy harvesters since plates and plate-type structures are commonly used in aerospace, automotive and marine applications. The aim of this paper is to present experiments and electroelastic finite element simulations of a piezoelectric energy harvester structurally integrated on a thin plate. The finite element model of the piezoceramic patch and the all-edges-clamped plate are built. In parallel, an experimental setup is constructed using a thin PZT-5A piezoceramic patch attached on the surface of all-edges-clamped rectangular aluminum plate. The electroelastic frequency response functions relating voltage output and vibration response to forcing input are validated using the experimentally obtained results. Finally, electrical power generation of the piezoceramic patch is investigated using the experimental set-up for a set of resistive loads. The numerical predictions and experimental results show that the use of all-edge-clamped flexible plate as host structure for piezoelectric energy harvester leads to multimodal vibration-to-electricity conversion.

Parametric analysis of multilayered unimorph piezoelectric vibration energy harvesters

2015 ◽  
Vol 23 (15) ◽  
pp. 2538-2553 ◽  
Author(s):  
Ahmed Jemai ◽  
Fehmi Najar ◽  
Moez Chafra
Keyword(s):  
Energy Harvester ◽  
Electrical Power ◽  
Closed Form Solution ◽  
Beam Theory ◽  
Load Resistance ◽  
Form Solution ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Piezoelectric Cantilever ◽  
Piezoelectric Layers

The use of a multilayer piezoelectric cantilever beam for vibration-based energy harvesting applications has been investigated as an effective technique to increase the harvested electrical power. It has been shown that the multilayered energy harvester performance is very sensitive to the number of layers and their electrical connection due to impedance variations. The objective of this work is to suggest a comprehensive mathematical model of multilayered unimorph piezoelectric energy harvester allowing analytical solution for the harvested voltage and electrical power. The model is used to deeply investigate the influence of different parameters on the harvested power. A distributed-parameter model of the harvester using the Euler–Bernoulli beam theory and Hamilton's principle is derived. Gauss's law is used to derive the electrical equations for parallel and series connections. A closed-form solution is proposed based on the Galerkin procedure and the obtained results are validated with a finite element 3D model. A parametric study is performed to ascertain the influence of the load resistance, the thickness ratio, the number of piezoelectric layers on the tip displacement and the electrical harvested power. It is shown that this model can be easily used to adjust the geometrical and electrical parameters of the energy harvester in order to improve the system's performances. In addition, it is proven that if one of the system's parameter is not correctly tuned, the harvested power can decrease by several orders of magnitude.

Energy Harvesting From Broadband Random Vibrations: Comparison of Single-Mode and Multi-Mode Electroelastic Solutions

2012 ◽  
Author(s):  
Sihong Zhao ◽  
Alper Erturk
Keyword(s):  
Energy Harvesting ◽  
White Noise ◽  
Energy Harvester ◽  
Vibrational Energy ◽  
Single Mode ◽  
Random Excitation ◽  
Distributed Parameter ◽  
Random Vibrations ◽  
Piezoelectric Energy ◽  
Multi Mode

Vibration-based energy harvesting has been heavily researched over the last decade with a primary focus on resonant excitation. However, ambient vibrational energy often has broader frequency content than a single harmonic, and in many cases it is entirely stochastic. As compared to the literature of deterministic energy harvesting, very few authors presented modeling approaches for energy harvesting from broadband random vibrations. These efforts have combined the input statistical information with the single-degree-of-freedom (SDOF) dynamics of the energy harvester to express the statistical electromechanical response characteristics. In most cases, the motion input (base acceleration) is assumed to be ideal white noise. White noise has a flat power spectral density (PSD) that might in fact excite higher vibration modes of an electroelastic energy harvester. In particular, piezoelectric energy harvesters constitute such continuous electroelastic systems with more than one vibration mode. This paper presents modeling and simulations of piezoelectric energy harvesting from broadband random vibrations based on distributed-parameter electroelastic solution. For white noise–type base acceleration of a given PSD level, first the general solution of the distributed-parameter problem is given. Closed-form representations are extracted for the single-mode case and these are analogous to the SDOF equations reported in the literature of energy harvesting. It is reported that the single-mode predictions might result in significant mismatch as compared to multi-mode predictions. Using the electroelastic solution, soft and hard piezoelectric power generators are compared under broadband random excitation. Shunt damping effect of power generation on the stochastic vibration response under broadband random excitation is also reported.

scholarly journals An Improved Lumped Parameter Model for a Piezoelectric Energy Harvester in Transverse Vibration

2014 ◽  
Vol 2014 ◽  
pp. 1-12 ◽  
Author(s):  
Guang-qing Wang ◽  
Yue-ming Lu
Keyword(s):  
Correction Factor ◽  
Transverse Vibration ◽  
Energy Harvester ◽  
Lumped Parameter Model ◽  
Distributed Parameter ◽  
Piezoelectric Energy ◽  
Distributed Parameter Model ◽  
Lumped Parameter ◽  
Lumped Parameter Models ◽  
Tip Mass

An improved lumped parameter model (ILPM) is proposed which predicts the output characteristics of a piezoelectric vibration energy harvester (PVEH). A correction factor is derived for improving the precisions of lumped parameter models for transverse vibration, by considering the dynamic mode shape and the strain distribution of the PVEH. For a tip mass, variations of the correction factor with PVEH length are presented with curve fitting from numerical solutions. The improved governing motion equations and exact analytical solution of the PVEH excited by persistent base motions are developed. Steady-state electrical and mechanical response expressions are derived for arbitrary frequency excitations. Effects of the structural parameters on the electromechanical outputs of the PVEH and important characteristics of the PVEH, such as short-circuit and open-circuit behaviors, are analyzed numerically in detail. Accuracy of the output performances of the ILPM is identified from the available lumped parameter models and the coupled distributed parameter model. Good agreement is found between the analytical results of the ILPM and the coupled distributed parameter model. The results demonstrate the feasibility of the ILPM as a simple and effective means for enhancing the predictions of the PVEH.

An asymmetric magnetic-coupled bending-torsion piezoelectric energy harvester: modeling and experimental investigation

2021 ◽  
Author(s):  
Huirong Zhang ◽  
Wentao Sui ◽  
Chongqiu Yang ◽  
Leian Zhang ◽  
Rujun Song ◽  
...  
Keyword(s):  
Energy Harvester ◽  
Average Power ◽  
Harmonic Excitation ◽  
Lumped Parameter Model ◽  
Distributed Parameter ◽  
Piezoelectric Energy ◽  
Distributed Parameter Model ◽  
Piezoelectric Beam ◽  
Lumped Parameter ◽  
Torsion Energy

Abstract This paper presents a detailed investigation on an asymmetric magnetic-coupled bending-torsion piezoelectric energy harvester based on harmonic excitation. There is an eccentricity between the shape center of moving magnets and the axis of the piezoelectric beam, which results in the bending and torsion simultaneously in working condition. The distributed mathematical model is derived from the energy method to describe the dynamic characteristics of the harvester, and the correctness of the model is verified by experiments. To further demonstrate the improvement performance of the proposed energy harvester, the bending-torsion energy harvester (i.e. magnetic-coupled was not configured) is experimented and compared. The theoretical and experimental results indicate that the average power increases about 300% but the resonance frequency decreases approximately 2 Hz comparing to the harvester without magnetic-coupled. According to the characteristic of distributed parameter model, the magnetic force and the size of the piezoelectric beam are investigated respectively. And the lumped-parameter model is introduced to analyze the steady-state characteristic. Accordingly, this paper provides a feasible method to improve performance for piezoelectric energy harvester.

scholarly journals Energy Harvesting Backpacks for Human Load Carriage: Modelling and Performance Evaluation

Electronics ◽  
2020 ◽  
Vol 9 (7) ◽  
pp. 1061
Author(s):  
Ledeng Huang ◽  
Ruishi Wang ◽  
Zhenhua Yang ◽  
Longhan Xie
Keyword(s):  
Energy Harvesting ◽  
Energy Harvester ◽  
Electrical Power ◽  
Metabolic Cost ◽  
Energy Performance ◽  
Load Carriage ◽  
Metabolic Power ◽  
Power Sources ◽  
Energy Harvesters ◽  
And Performance

In recent years, there has been an increasing demand for portable power sources as people are required to carry more equipment for occupational, military, or recreational purposes. The energy harvesting backpack that moves relative to the human body, could capture kinetic energy from human walking and convert vertical oscillation into the rotational motion of the generators to generate electricity. In our previous work, a light-weight tube-like energy harvester (TL harvester) and a traditional frequency-tuneable backpack-based energy harvester (FT harvester) were proposed. In this paper, we discuss the power generation performance of the two types of energy harvesters and the energy performance of human loaded walking, while carrying energy harvesting backpacks, based on two different spring-mass-damper models. Testing revealed that the electrical power in the experiments showed similar trends to the simulation results, but the calculated electrical power and the net metabolic power were higher than that of the experiments. Moreover, the total cost of harvesting (TCOH), defined as additional metabolic power in watt required to generate 1 W of electrical power, could be negative, which indicated that there is a chance to generate 6.11 W of electricity without increasing the metabolic cost while carrying energy harvesting backpacks.

scholarly journals Power Harvesting Capabilities of SHM Ultrasonic Sensors

2012 ◽  
Vol 2012 ◽  
pp. 1-7 ◽  
Author(s):  
Christophe Delebarre ◽  
Thomas Sainthuile ◽  
Sébastien Grondel ◽  
Christophe Paget
Keyword(s):  
Structural Health Monitoring ◽  
Energy Harvesting ◽  
Health Monitoring ◽  
Energy Harvester ◽  
Voltage Response ◽  
Ultrasonic Sensors ◽  
Power Harvesting ◽  
Structural Health ◽  
Piezoelectric Energy ◽  
Power Harvester

The aim of this work is to show that classical Structural Health Monitoring ultrasonic sensors may provide some power harvesting capabilities from a wide variety of vibration sources. In other words, the authors developed an integrated piezoelectric energy harvesting sensor capable of operating a dual mode, that is, carrying out vibration power harvesting and Structural Health Monitoring. First, vibrations signals of an A380 aircraft recorded during different phases of flight are presented to show the need of a wideband piezoelectric energy harvester. Then, the voltage response of a piezoelectric power harvester bonded onto an aluminium cantilever plate and excited by an electromechanical shaker is measured. A finite element model of the energy harvester system is also presented. This model provides the voltage response of the harvester due to a mechanical excitation of the host structure and allows a better understanding of the energy harvesting process. In many cases, a good agreement with the experimental results is obtained. A power measurement also showed the ability of piezoelectric SHM sensors to harvest power over an extended frequency range present in spectra collected in aircrafts. This result could lead to numerous applications even though this kind of power harvester sensor has been initially designed to operate onboard aircrafts.

Sign in / Sign up

Export Citation Format

Share Document