Research on dynamic characteristics of gear system considering the influence of temperature on material performance

2021 ◽  
pp. 107754632110026
Author(s):  
Zhou Sun ◽  
Siyu Chen ◽  
Xuan Tao ◽  
Zehua Hu
Keyword(s):  
Elastic Modulus ◽  
Dynamic Characteristics ◽  
Poisson’S Ratio ◽  
Gear System ◽  
Poisson's Ratio ◽  
Effect Of Temperature ◽  
Time Varying ◽  
Influence Of Temperature ◽  
Meshing Stiffness ◽  
Influence Of Temperature On

Under high-speed and heavy-load conditions, the influence of temperature on the gear system is extremely important. Basically, the current work on the effect of temperature mostly considers the flash temperature or the overall temperature field to cause expansion at the meshing point and then affects nonlinear factors such as time-varying meshing stiffness, which lead to the deterioration of the dynamic transmission. This work considers the effect of temperature on the material’s elastic modulus and Poisson’s ratio and relates the temperature to the time-varying meshing stiffness. The effects of temperature on the elastic modulus and Poisson’s ratio are expressed as functions and brought into the improved energy method stiffness calculation formula. Then, the dynamic characteristics of the gear system are analyzed. With the bifurcation diagram, phase, Poincaré, and fast Fourier transform plots of the gear system, the influence of temperature on the nonlinear dynamics of the gear system is discussed. The numerical analysis results show that as the temperature increases, the dynamic response of the system in the middle-speed region gradually changes from periodic motion to chaos.

Experimental Study on the Influence of Temperature on Shale Mechanical Properties under Conventional Triaxial Compression

2011 ◽  
Vol 250-253 ◽  
pp. 1452-1455 ◽  
Author(s):  
Lu Bo Meng ◽  
Tian Bin Li ◽  
Liang Wen Jiang ◽  
Hong Min Ma
Keyword(s):  
Mechanical Properties ◽  
Thermal Stress ◽  
Elastic Modulus ◽  
High Temperature ◽  
Poisson’S Ratio ◽  
Triaxial Compression ◽  
Poisson's Ratio ◽  
Influence Of Temperature ◽  
Conventional Triaxial Compression ◽  
Influence Of Temperature On

High temperature conventional triaxial compression test of shale are carried out by the MTS815 servo-controlled testing machine, based on the experimental results, the relationships between temperature and shale peak strength, elastic modulus, Poisson's ratio, cohesion, internal friction angle are investigated. Although the experimental results are discrete comparatively, the general law is obvious. When the confining pressure imposed on shale is constant and the temperature changes form 25°C to 120°C, with the increasing of the temperature, the triaxial compression strength, shear strength gradually increase, while average elastic modulus, Poisson's ratio has a slightly decrease. The thermal stress generated by the high temperature plays a role to accommodate the deformation and the function of preventing crack propagation, thus the bearing capacity of shale samples are strengthened. But the influence of temperature on shale mechanical properties mutates when the temperature is at 80°C. Shale peak strength dramatically decreased, average elastic modulus decreased slightly, and Poisson's ratio also increased slightly, which indicated that at 80°C, different thermal expansivity of mineral particles of shale may cause cross-grain boundary thermal expansion incongruous, creating additional thermal stress, thus the sample’s bearing capacity decreased.

The effect of temperature on high-resolution TEM image contrast

1995 ◽  
Vol 53 ◽  
pp. 640-641
Author(s):  
T. Geipel ◽  
W. Mader ◽  
P. Pirouz
Keyword(s):  
Form Factor ◽  
Inelastic Scattering ◽  
Accurate Method ◽  
Waller Factor ◽  
Effect Of Temperature ◽  
Specimen Thickness ◽  
Influence Of Temperature ◽  
Debye Waller Factor ◽  
Influence Of Temperature On ◽  
Atomic Form Factor

Temperature affects both elastic and inelastic scattering of electrons in a crystal. The Debye-Waller factor, B, describes the influence of temperature on the elastic scattering of electrons, whereas the imaginary part of the (complex) atomic form factor, fc = fr + ifi, describes the influence of temperature on the inelastic scattering of electrons (i.e. absorption). In HRTEM simulations, two possible ways to include absorption are: (i) an approximate method in which absorption is described by a phenomenological constant, μ, i.e. fi; - μfr, with the real part of the atomic form factor, fr, obtained from Hartree-Fock calculations, (ii) a more accurate method in which the absorptive components, fi of the atomic form factor are explicitly calculated. In this contribution, the inclusion of both the Debye-Waller factor and absorption on HRTEM images of a (Oll)-oriented GaAs crystal are presented (using the EMS software.Fig. 1 shows the the amplitudes and phases of the dominant 111 beams as a function of the specimen thickness, t, for the cases when μ = 0 (i.e. no absorption, solid line) and μ = 0.1 (with absorption, dashed line).

The Model for Calculating Elastic Modulus and Poisson's Ratio of Coal Body

2013 ◽  
Vol 6 (1) ◽  
pp. 36-43 ◽  
Author(s):  
Ai Chi ◽  
Li Yuwei
Keyword(s):  
Elastic Modulus ◽  
Poisson’S Ratio ◽  
Fractured Rock ◽  
Rock Block ◽  
Poisson's Ratio ◽  
Linear Elastic ◽  
Study Results ◽  
The Face ◽  
Block Face ◽  
Coal Rock

Coal body is a type of fractured rock mass in which lots of cleat fractures developed. Its mechanical properties vary with the parametric variation of coal rock block, face cleat and butt cleat. Based on the linear elastic theory and displacement equivalent principle and simplifying the face cleat and butt cleat as multi-bank penetrating and intermittent cracks, the model was established to calculate the elastic modulus and Poisson's ratio of coal body combined with cleat. By analyzing the model, it also obtained the influence of the parameter variation of coal rock block, face cleat and butt cleat on the elastic modulus and Poisson's ratio of the coal body. Study results showed that the connectivity rate of butt cleat and the distance between face cleats had a weak influence on elastic modulus of coal body. When the inclination of face cleat was 90°, the elastic modulus of coal body reached the maximal value and it equaled to the elastic modulus of coal rock block. When the inclination of face cleat was 0°, the elastic modulus of coal body was exclusively dependent on the elastic modulus of coal rock block, the normal stiffness of face cleat and the distance between them. When the distance between butt cleats or the connectivity rate of butt cleat was fixed, the Poisson's ratio of the coal body initially increased and then decreased with increasing of the face cleat inclination.

Flow Behaviors of High Acyl Gellan Aqueous Solutions as Affected by Temperature, and Calcium and Gellan Concentrations

2008 ◽  
Vol 4 (5) ◽  
Author(s):  
Yiqun Huang ◽  
Pawan Singh Takhar ◽  
Juming Tang ◽  
Barry G Swanson
Keyword(s):  
Shear Rate ◽  
Aqueous Solutions ◽  
Apparent Viscosity ◽  
Flow Resistance ◽  
Effect Of Temperature ◽  
Temperature Changes ◽  
Influence Of Temperature ◽  
Rheological Behaviors ◽  
Low Concentrations ◽  
Influence Of Temperature On

Rheological behaviors of high acyl (HA) gellan are not well understood partially because of its relatively late commercialization compared to low acyl gellan. The objective of this study was to investigate the effect of temperature (5-30 °C), calcium (0, 1 and 10 mM) and gellan concentrations (0.0044-0.1000% w/v) on the flow behaviors of high acyl gellan aqueous solutions using rheological tests. Gellan solutions with 0 or 1 mM added Ca++ exhibited shear thinning behavior at gellan concentrations above 0.0125%. The influence of temperature on apparent viscosity (shear rate, 100 s-1) of gellan solutions can be described with an Arrhenius relationship. The apparent viscosity of gellan solution at low concentrations was more sensitive to temperature changes. The addition of Ca++ led to a decrease in flow resistance for a dilute gellan solution (<0.0125%), but an increased resistance for a relatively concentrated gellan solution (>0.0125%).

Measurement of Cement in Situ Stresses and Mechanical Properties Without Cooling or Depressurization

2021 ◽  
Author(s):  
Meng Meng ◽  
Luke Frash ◽  
James Carey ◽  
Wenfeng Li ◽  
Nathan Welch ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mechanical Property ◽  
Elastic Modulus ◽  
Poisson’S Ratio ◽  
Axial Stress ◽  
Triaxial Compression ◽  
In Situ Measurement ◽  
Poisson's Ratio ◽  
Ambient Conditions

Abstract Accurate characterization of oilwell cement mechanical properties is a prerequisite for maintaining long-term wellbore integrity. The drawback of the most widely used technique is unable to measure the mechanical property under in situ curing environment. We developed a high pressure and high temperature vessel that can hydrate cement under downhole conditions and directly measure its elastic modulus and Poisson's ratio at any interested time point without cooling or depressurization. The equipment has been validated by using water and a reasonable bulk modulus of 2.37 GPa was captured. Neat Class G cement was hydrated in this equipment for seven days under axial stress of 40 MPa, and an in situ measurement in the elastic range shows elastic modulus of 37.3 GPa and Poisson's ratio of 0.15. After that, the specimen was taken out from the vessel, and setted up in the triaxial compression platform. Under a similar confining pressure condition, elastic modulus was 23.6 GPa and Possion's ratio was 0.26. We also measured the properties of cement with the same batch of the slurry but cured under ambient conditions. The elastic modulus was 1.63 GPa, and Poisson's ratio was 0.085. Therefore, we found that the curing condition is significant to cement mechanical property, and the traditional cooling or depressurization method could provide mechanical properties that were quite different (50% difference) from the in situ measurement.

scholarly journals Effect of Temperature on Formaldehyde Diffusion in Cellulose Amorphous Region: A Simulation Study

BioResources ◽  
2021 ◽  
Vol 16 (2) ◽  
pp. 3200-3213
Author(s):  
Wei Wang ◽  
Yancai Cao ◽  
Liyue Sun ◽  
Mingshuai Wu
Keyword(s):  
Shear Modulus ◽  
Bulk Modulus ◽  
Poisson’S Ratio ◽  
Amorphous Region ◽  
Poisson's Ratio ◽  
Effect Of Temperature ◽  
External Temperature ◽  
Practical Applications ◽  
Region Model ◽  
Materials Studio

A formaldehyde-cellulose amorphous region model at the micro-level was established using the molecular dynamics software Materials Studio to simulate the change of cellulose and formaldehyde molecules in an external temperature field. The diffusion coefficients of formaldehyde molecules increased as the temperature increased. Moreover, the total number of hydrogen bonds decreased, and the interaction energy in the formaldehyde-cellulose model was reduced, which confirmed this conclusion and indicated that temperature increase could enhance the diffusion of formaldehyde in cellulose. The mechanical parameters of cellulose were analyzed in terms of Young’s modulus, shear modulus, bulk modulus, Poisson’s ratio, and the ratio of bulk modulus to shear modulus (K/G), which were affected by the temperature. The elastic modulus (E, G, and K) of cellulose decreased as the temperature increased, while the Poisson’s ratio V and K/G values increased. The results of the research explain how elevated temperature can promote the release of formaldehyde in furniture from a microscopic perspective, which supports each other with the results of previous experimental data and practical applications in production.

Elasto-Plastic Hemispherical Contact Models for Various Mechanical Properties

2005 ◽  
Author(s):  
John J. Quicksall ◽  
Robert L. Jackson ◽  
Itzhak Green
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Material Properties ◽  
Poisson’S Ratio ◽  
Carbon Steels ◽  
Poisson's Ratio ◽  
Aluminum Bronze ◽  
Contact Models ◽  
Element Technique ◽  
Malleable Cast

This work uses the finite element technique to model the elasto-plastic deformation of a hemisphere contacting a rigid flat for various material properties typical of aluminum, bronze, copper, titanium and malleable cast iron. Additionally, this work conducted parametric FEM tests on a generic material in which the elastic modulus and Poisson’s ratio are varied independently while the yield strength is held constant. A larger spectrum of material properties are covered in this work than in most previous works. The results are compared to two previously formulated elasto-plastic models simulating the deformation of a hemisphere in contact with a rigid flat. Both of the previously formulated models use carbon steel mechanical properties to arrive at empirical formulations implied to pertain to various materials. While both models considered several carbon steels with varying yield strengths, they did not test materials with varying Poisson’s ratio or elastic modulus. The previously generated elasto-plastic models give fairly good predictions when compared to the FEM results for various material properties from the current work, except that one model produces more accurate predictions overall, especially at large deformations where other models neglect important trends due to decreases in “hardness” with increasing deformation.

Biomimetic composites inspired by venous leaf

2017 ◽  
Vol 52 (3) ◽  
pp. 361-372 ◽  
Author(s):  
Gongdai Liu ◽  
R Ghosh ◽  
A Vaziri ◽  
A Hossieni ◽  
D Mousanezhad ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Yield Stress ◽  
Poisson’S Ratio ◽  
Composite Structures ◽  
Volume Fraction ◽  
Matrix Material ◽  
Poisson's Ratio ◽  
Fiber Volume ◽  
Young’S Moduli

A typical plant leaf can be idealized as a composite having three principal fibers: the central mid-fiber corresponding to the mid-rib, straight parallel secondary fibers attached to the mid-fiber representing the secondary veins, and then another set of parallel fibers emanating from the secondary fibers mimicking the tertiary fibers embedded in a matrix material. This paper introduces a biomimetic composite design inspired by the morphology of venous leafs and investigates the effects of venation morphologies on the in-plane mechanical properties of the biomimetic composites using finite element method. The mechanical properties such as Young’s moduli, Poisson’s ratio, and yield stress under uniaxial loading of the resultant composite structures was studied and the effect of different fiber architectures on these properties was investigated. To this end, two broad types of architectures were used both having similar central main fiber but differing in either having only secondary fibers or additional tertiary fibers. The fiber and matrix volume fractions were kept constant and a comparative parametric study was carried out by varying the inclination of the secondary fibers. The results show that the elastic modulus of composite in the direction of main fiber increases linearly with increasing the angle of the secondary fibers. Furthermore, the elastic modulus is enhanced if the secondary fibers are closed, which mimics composites with closed cellular fibers. In contrast, the elastic modulus of composites normal to the main fiber ( x direction) exponentially decreases with the increase of the angle of the secondary fibers and it is little affected by having secondary fibers closed. Similar results were obtained for the yield stress of the composites. The results also indicate that Poisson’s ratio linearly increases with the secondary fiber angle. The results also show that for a constant fiber volume fraction, addition of various tertiary fibers may not significantly enhance the mechanical properties of the composites. The mechanical properties of the composites are mainly dominated by the secondary fibers. Finally, a simple model was proposed to predict these behaviors.

Sign in / Sign up

Export Citation Format

Share Document