Effect of Moisture Content and Screw Speed on the Physical Chemical Properties of an Extruded Crab-based Snack

2005 ◽  
Vol 11 (2) ◽  
pp. 121-127 ◽  
Author(s):  
V. A. Obatolu ◽  
D. I. Skonberg ◽  
M. E. Camire ◽  
M. P. Dougherty
Keyword(s):  
Moisture Content ◽  
Physical Properties ◽  
Chemical Properties ◽  
Value Added ◽  
Expansion Ratio ◽  
Screw Speed ◽  
Twin Screw ◽  
L Value ◽  
By Products ◽  
Value Added Products

Crab processing generates by-products that could be used in new value-added products to decrease processing waste and increase profits. In this product development study, the effects of moisture content and screw speed on physical properties and composition of an extruded crab-based snack product were investigated. Corn meal was fortified with 10% ground crab leg and passed through a twin-screw extruder using moisture contents of 25% and 30% and screw speeds of 200, 250 and 300rpm for a total of six treatments, extruded in duplicate. Screw speed and moisture content had a significant (p 0.05) influence on moisture content, expansion ratio, crunchiness and L-value of the extrudate while protein, fat, ash and mineral were not significantly (p 0.05) affected. As screw speed increased, moisture content and bulk density of the extrudates decreased. The snack product extruded at 25% moisture content and 300rpm had significantly different (p 0.05) physical properties compared to all other treatments. Increases in torque and melting temperature were observed for higher screw speed and lower extruding moisture content.

scholarly journals Effects of Twin-Screw Extruders Condition to Physical Properties of Floating Fish Feed

2019 ◽  
Vol 21 (2) ◽  
pp. 79
Author(s):  
Arif Rahman Hakim ◽  
Wahyu Tri Handoyo ◽  
Toni Dwi Novianto ◽  
Andrianto Widi Prasetyo
Keyword(s):  
Moisture Content ◽  
Chemical Properties ◽  
Expansion Ratio ◽  
Fish Feed ◽  
Screw Speed ◽  
Twin Screw Extruders ◽  
Twin Screw ◽  
Unit Density ◽  
Screw Extruders ◽  
Ratio Unit

Process production of floating fish feed in a society constrained by processing technology. The objective of this study was to observe effect of  condition process of twin screw extruders to the physical and chemical properties of produced of floating fish feed. Ingredients used involve fish meal, soybean meal, corn meal, and tapioca flour. The ingredients are mixed with 15, 20 and 25% water added to the total weight. Extrusion process condition conducted by several treatments i.e screw speed (540, 540, 600, 660 rpm) and barrel temperatures (80, 90, 100, 110, 120℃). In order to study, expansion ratio, unit density, floatability and hardness of feed were observed as physical parameters while chemical properties include moisture and protein content. Experimental result showed that addition 25 % water to the formula gives a good performance of expansion ratio, unit density and floatability than 15% and 20% moisture content. Higher of screw speed produces feed with higher ratio expansion, lower unit density, and higher floatability. The optimum of screw speed is 600 rpm.  Meanwhile increasing of barrel temperature caused reduction of unit density, and escalation floatability of feed. Best barrel temperature to meet the physical properties is 120℃. The produced feed contain protein 32.38-41.95% and moisture content 4.37-5.70%.

Feasibility of utilizing sweet potato solids in extrusion cooking / Extrusión de pulpa de batata

1997 ◽  
Vol 3 (3) ◽  
pp. 171-174 ◽  
Author(s):  
H.M. Khalil ◽  
B.R. Henry
Keyword(s):  
Moisture Content ◽  
Sweet Potato ◽  
Sugar Content ◽  
Expansion Ratio ◽  
Fractional Factorial ◽  
Snack Food ◽  
Screw Speed ◽  
High Sugar Content ◽  
Feed Moisture ◽  
Best Parameter

A fractional factorial design of four variables at two levels each was employed to assess the feasi bility and best parameter for extruding sweet potato solids (SPS) using a single screw extruder. It was determined that a high expansion ratio is a desired quality factor for this type of snack food, due to its contribution to textural perception. Preliminary trials on extrusion of sweet potato solids as the sole component in the feed resulted in brittle, dense, and burnt extrudate. The high sugar content (65% total sugar) of the sweet potato solids was cited as the cause of these attrib utes, consequently it was necessary to incorporate wheat flour into the feed to provide a starch matrix for expansion and to reduce sugar concentration. The controlled parameters were screw speed, barrel temperature, feed moisture content, and SPS level in the feed. Among all possible combinations of controlled parameters, the highest expansion ratio was obtained at a screw speed of 220 rpm, temperature profile of 110, 105, 115 and 105 °C, 13% feed moisture content, 50% sweet potato solids, and 0.5% leavening agent.

scholarly journals Utilization of marine by-products for the recovery of value-added products

2019 ◽  
Vol 6 ◽  
Author(s):  
Fereidoon Shahidi ◽  
Vamadevan Varatharajan ◽  
Han Peng ◽  
Ruchira Senadheera
Keyword(s):  
Fish Meal ◽  
Value Added ◽  
Food Ingredients ◽  
Fisheries Resources ◽  
Feed Production ◽  
Lipid Fractions ◽  
By Catch ◽  
Fish And Shellfish ◽  
By Products ◽  
Value Added Products

The world fisheries resources have exceeded 160 million tons in recent years. However, every year a considerable amount of total catch is discarded as by-catch or as processing leftovers, and that includes trimmings, fins, frames, heads, skin, viscera and among others. In addition, a large quantity of processing by-products is accumulated as shells of crustaceans and shellfish from marine bioprocessing plants. Recognition of the limited marine resources and the increasing environmental pollution has emphasized the need for better utilization of the by-products. Marine by-products contain valuable protein and lipid fractions, minerals, enzymes as well as many other components. The major fraction of by-products are used for feed production—in making fish meal/oil, but this has low profitability. However, there are many ways in which the fish and shellfish waste could be better utilized, including the production of novel food ingredients, nutraceuticals, pharmaceuticals, biomedical materials, fine chemicals, and other value-added products. In recent times, much research is conducted in order to explore the possible uses of different by-products. This contribution primarily covers the characteristics and utilization of the main ingredients such as protein, lipid, chitin and its derivatives, enzymes, carotenoids, and minerals originating from marine by-products.

scholarly journals Retraction: Bigger data open innovation: potential applications of value-added products from milk and sustainable valorization of by-products from the dairy industry

2017 ◽  
Vol 19 (13) ◽  
pp. 3164-3164
Author(s):  
S. Ortega-Requena ◽  
S. Rebouillat
Keyword(s):  
Open Innovation ◽  
Dairy Industry ◽  
Value Added ◽  
Innovation Potential ◽  
Potential Applications ◽  
By Products ◽  
Value Added Products

Retraction of ‘Bigger data open innovation: potential applications of value-added products from milk and sustainable valorization of by-products from the dairy industry’ by S. Ortega-Requena et al., Green Chem., 2015, 17, 5100–5113.

scholarly journals Modeling Single-Screw Extrusion Processing Parameters and Resulting Extrudate Properties of DDGS-Based Nile Tilapia (Oreochromis niloticus) Feeds

2013 ◽  
Vol 2 (2) ◽  
pp. 11 ◽  
Author(s):  
Ferouz Y. Ayadi ◽  
Parisa Fallahi ◽  
Kurt A. Rosentrater ◽  
Kasiviswanathan Muthukumarappan
Keyword(s):  
Moisture Content ◽  
Physical Properties ◽  
Soybean Meal ◽  
Nile Tilapia ◽  
Processing Parameters ◽  
Expansion Ratio ◽  
Fractional Factorial ◽  
Processing Conditions ◽  
Font Size ◽  
Single Screw

<span style="font-family: Times New Roman; font-size: small;"> </span><p class="MsoNoSpacing" style="margin: 0in 0in 0pt; line-height: 115%;">A single-screw laboratory extruder was used to conduct an L<sub>18</sub> (2<sup>2</sup><sup> </sup>´ 3<sup>6</sup>) Taguchi fractional factorial study of aquafeed processing. The ingredients were based on a formulation for nutritionally-balanced Nile tilapia diets containing distillers dried grains with solubles (DDGS) and soybean meal as the main protein sources, in addition to constant amounts of corn flour, whey, and fishmeal. The effects of three levels of DDGS (20, 30 and 40%), soybean meal (30, 40 and 50%), ingredient moisture content (20, 30 and 40% db), screw speed (100, 150 and 200 rpm), die dimension (L/D ratios of 5, 9 and 13), barrel temperature (80-100-100°C, 80-120-120°C and 80-140-140°C) and two levels of screw configuration (compression ratios of 2:1 and 3:1) on extrudate physical properties (moisture content, water activity, bulk density, unit density, expansion ratio, pellet durability index, water absorption and solubility indices, water stability, color) and extruder processing parameters (resulting temperatures, die pressure, extruder torque, mass flow rate, apparent viscosity, and specific mechanical energy) were determined. Data from raw materials, processing conditions, and extrudate properties were used to develop surface response curves and equations. However, predominantly low R<sup>2</sup> values (&lt; 0.5) only permitted linear relationships between some independent parameters and response variables. Regarding main effects, die pressure significantly decreased with higher DDGS levels, moisture content, temperature, lower die L/D, and higher screw compression. Expansion ratio decreased significantly with higher moisture content and lower die L/D. Significant differences in color were caused by changes in DDGS levels and moisture content. In summary, DDGS, moisture content, die dimension, and extrusion conditions had the biggest impact on most of the extrudate physical properties and processing conditions. Different combinations of these independent factors can be used to achieve desired extrudate physical properties and processing conditions.</p><span style="font-family: Times New Roman; font-size: small;"> </span>

scholarly journals PENGARUH PROPORSI DAMI NANGKA TERHADAP KARAKTERISTIK KIMIA, FISIK DAN ORGANOLEPTIK SELAI LEMBARAN NANAS

Pro Food ◽  
2020 ◽  
Vol 6 (2) ◽  
pp. 685
Author(s):  
Ni Made Neni Parmiutari ◽  
Eko Basuki ◽  
Rucitra Widyasari
Keyword(s):  
Moisture Content ◽  
Analysis Of Variance ◽  
Chemical Properties ◽  
Randomized Design ◽  
Yellow Color ◽  
Significant Difference ◽  
L Value ◽  
Completely Randomized Design ◽  
Total Dissolved Solid ◽  
Difference Test

ABSTRACT             This study aims to determine the chemical properties (moisture content, pH and total dissolved solid), physical properties (texture and color) and organoleptics (taste, color, aroma, texture) in the different formulation of slice jam from mixture straw jackfruit and pineapple. This study used a Completely Randomized Design (CRD) with 6 treatments and 3 time replications and analyzed using Analysis of Variance at the 5% level and followed by Least Significant Difference test at the 5% level. These treatments include P0 (100 % pineapple), P1 (80% pineapple: 20% straw jackfruit), P2 (65% pineapple: 35% straw jackfruit), P3 (50% pineapple: 50% straw jackfruit), P4 (35% pineapple: 65% straw jackfruit), dan P5 (20% pineapple: 80% straw jackfruit). Observations made on moisture content, pH, total dissolved solid, texture, color and organoleptic taste, color, texture and aroma (scoring and hedonic). The results showed that the P3 treatment (50% straw jackfruit: 50% pineapple) was the preferred treatment for the panelists on the parameters of color, taste, and texture with the characteristics of moisture content 23.35%, pH 4.86, total dissolved solids 32,46oBrix, L value 44.79 and Hue value 70.67o and brownish yellow color, slightly pineapple taste, chewy texture and pineapple aroma and slightly jackfruit aroma. Keywords: pineapple, slice jam, straw jackfruit ABSTRAK       Penelitian ini bertujuan untuk mengetahui sifat kimia (kadar air, pH dan total padatan terlarut), sifat fisik (tekstur dan warna) dan organoleptik (rasa, warna, aroma, tekstur) pada formulasi selai lembaran dari campuran dami nangka dan buah nanas yang berbeda. Penelitian ini menggunakan Rancangan Acak Lengkap (RAL) dengan 6 perlakuan dan 3 kali ulangan dan dianalisis menggunakan analisis keragaman (Analysis of Variance) pada taraf 5% dan dilanjutkan dengan uji Beda Nyata Terkecil pada taraf 5%. Perlakuan diantaranya P0 (100 % buah nanas), P1 (80% buah nanas: 20% dami nangka), P2 (65% buah nanas: 35% dami nangka), P3 (50% buah nanas: 50% dami nangka), P4 (35% buah nanas: 65% dami nangka), dan P5 (20% buah nanas: 80% dami nangka). Pengamatan dilakukan terhadap kadar air, pH, total padatan terlarut, tekstur, warna dan organoleptik rasa, warna, tekstur dan aroma (skoring dan hedonik). Hasil penelitian menunjukkan bahwa perlakuan P3 (50% dami nangka : 50% buah nanas) merupakan perlakuan yang agak disukai panelis pada parameter warna, rasa, dan tekstur dengan karakteristik kadar air 23,35%, pH 4,86, total padatan terlarut 32,46oBrix, nilai L 44,79 dan nilai Hue 70,67o serta warna kuning kecokelatan, agak berasa asam nanas, tekstur kenyal dan beraroma nanas dan sedikit beraroma nangka. Kata kunci: buah nanas, dami nangka, selai lembaran

scholarly journals Utilization of marine by-products for the recovery of value-added products

2019 ◽  
Vol 6 ◽  
Author(s):  
Fereidoon Shahidi ◽  
Vamadevan Varatharajan ◽  
Han Peng ◽  
Ruchira Senadheera
Keyword(s):  
Fish Meal ◽  
Value Added ◽  
Food Ingredients ◽  
Fisheries Resources ◽  
Feed Production ◽  
Lipid Fractions ◽  
By Catch ◽  
Fish And Shellfish ◽  
By Products ◽  
Value Added Products

The world fisheries resources have exceeded 160 million tons in recent years. However, every year a considerable amount of total catch is discarded as by-catch or as processing leftovers, and that includes trimmings, fins, frames, heads, skin, viscera and among others. In addition, a large quantity of processing by-products is accumulated as shells of crustaceans and shellfish from marine bioprocessing plants. Recognition of the limited marine resources and the increasing environmental pollution has emphasized the need for better utilization of the by-products. Marine by-products contain valuable protein and lipid fractions, minerals, enzymes as well as many other components. The major fraction of by-products are used for feed production—in making fish meal/oil, but this has low profitability. However, there are many ways in which the fish and shellfish waste could be better utilized, including the production of novel food ingredients, nutraceuticals, pharmaceuticals, biomedical materials, fine chemicals, and other value-added products. In recent times, much research is conducted in order to explore the possible uses of different by-products. This contribution primarily covers the characteristics and utilization of the main ingredients such as protein, lipid, chitin and its derivatives, enzymes, carotenoids, and minerals originating from marine by-products.

scholarly journals Physico-Chemical Properties of Palmyrah (Borassus flabellifer L.) Natural and Value Added Products

2020 ◽  
pp. 396-401
Author(s):  
M. Chandra Surya Rao ◽  
D. V. Swami ◽  
P. Ashok ◽  
D. R. Salomi Suneetha ◽  
R. V. Sujatha ◽  
...  
Keyword(s):  
Agricultural Research ◽  
Chemical Properties ◽  
Value Added ◽  
Economic Potential ◽  
Value Addition ◽  
Southern States ◽  
Physico Chemical ◽  
In The Wild ◽  
Slow Growing ◽  
Value Added Products

Palmyrah palm has great economic potential and every part of the palm is useful in one way or the other.The palm is found growing widely in southern states of India. The palmyrah products like tender fruit endosperm (nungu), neera, jaggery and tuber flour are not commercialised as the value addition in palmyrah is not standardised. Even though palmyrah is an economically important palm, it has not received proper attention from the agricultural research workers, probably on account of the fact that it is very slow growing palm found mostly in the wild state. In this context knowing of physico chemical properties and development of value added products and popularizing the same is essential.

Sign in / Sign up

Export Citation Format

Share Document