Quasi-static and dynamic mechanical thermal performance of date palm/glass fiber hybrid composites

2020 ◽  
pp. 152808372095803
Author(s):  
Abderrazek Merzoug ◽  
Bachir Bouhamida ◽  
Zouaoui Sereir ◽  
Abderrezak Bezazi ◽  
Ali Kilic ◽  
...  
Keyword(s):  
Flexural Strength ◽  
Glass Fiber ◽  
Date Palm ◽  
Hybrid Composites ◽  
Weight Ratio ◽  
Fiber Surface ◽  
Damping Factor ◽  
Dynamic Mechanical ◽  
Naoh Solution ◽  
Composite Glass

The present work reports an experimental study on the thermal and mechanical properties of hybrid composites obtained from Petiole Date Palm Fiber (PDPF)/Glass fiber (GF) as reinforcement and vinylester resin (VE). In order to improve the fiber/matrix adhesion, palm fibers were alkali treated with 5% NaOH solution for 24 h–72h. SEM and ATR-FTIR analysis revealed that the 48 h treatment of PDFP with NaOH solution led to rough fiber surface. Vacuum assisted resin transfer molding (VARTM) system was used to produce four hybrid composites (30PDPF/0GF, 20PDPF/10GF, 10PDPF/20GF and 0PDPF/30GF) where the weight ratio of total fiber reinforcement was kept 30%. The treated palm fibers were arranged as a nonwoven mat and placed between woven glass fabrics. Tensile, flexural, dynamic mechanical thermal analysis (DMTA), and thermogravimetric (TGA) were carried out to evaluate the performance of the hybrid composites. The flexural strength and modulus for pure PDPF composite were found to be 60 MPa and 3.87 GPa respectively. Addition of 20%wt glass fiber led an increase in the thermal stability and an enhancement in the tensile and flexural strength by 71.72% and 74.51%, respectively compared to pure PDPF composite. However, the incorporation of 10% of PDPF increases the damping factor from 0.2 for the composite glass/VE to 0.54 for the hybrid 10PDPF/20GF. According to findings of this study, PDPF based composites can be used as non-structural parts in automotive and boat industries.

Correlation of fatigue behavior and dynamic mechanical properties of hybrid composites of polypropylene/short glass fibers/hollow glass beads

2021 ◽  
pp. 089270572199319
Author(s):  
Gustavo B Carvalho
Keyword(s):  
Stress Relaxation ◽  
Flexural Strength ◽  
Relaxation Rate ◽  
Hybrid Composites ◽  
Fatigue Behavior ◽  
Glass Fibers ◽  
Glass Beads ◽  
Hollow Glass ◽  
Dynamic Mechanical ◽  
Short Glass

Ternary hybrid composites of Polypropylene (PP)/Short Glass Fibers (GF)/Hollow Glass Beads (HGB) were prepared using untreated and aminosilane-treated HGB, compatibilized with maleated-PP, and with varying total and relative GF/HGB contents. Static/short-term flexural strength properties data revealed, through lower flexural strength values, that the presence of untreated HGB particles induces to fiber-polymer interfacial decoupling at much higher extent than in the presence of aminosilane-treated HGB particles. This phenomenon is also evident when evaluating the data from displacement-controlled three-point bending fatigue tests. Monitored up to 106 cycles, the analyzed hybrid composites presented distinct performance relative to their fatigue stress relaxation rate: the lower the matrix-reinforcements’ interfacial adhesion, more pronounced the stress relaxation rate as a function of the number of fatigue cycles. Dynamic Mechanical Thermal Analysis (DMTA) results could successfully reveal the hybrid composites behavior at the microstructural level when they were submitted to both static flexural test and fatigue, depending on the degree of interfacial interactions between the polymer matrix of PP and the hybrid reinforcements of GF and HGB (with and without aminosilane surface treatment).

scholarly journals Dynamic Mechanical Properties of Hybrid Layered Silicates/Kaolin Geopolymer Filler in Epoxy Composites

2017 ◽  
Vol 54 (3) ◽  
pp. 543-545 ◽  
Author(s):  
Yusrina Mat Daud ◽  
Kamarudin Hussin ◽  
Azlin Fazlina Osman ◽  
Che Mohd Ruzaidi Ghazali ◽  
Mohd Mustafa Al Bakri Abdullah ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Speed ◽  
Hybrid Composites ◽  
Loss Modulus ◽  
Dynamic Mechanical Properties ◽  
Mechanical Analysis ◽  
Layered Silicates ◽  
Epoxy Composites ◽  
Damping Factor ◽  
Dynamic Mechanical

Preparation epoxy based hybrid composites were involved kaolin geopolymer filler, organo-montmorillonite at 3phr by using high speed mechanical stirrer. A mechanical behaviour of neat epoxy, epoxy/organo-montmorillonite and its hybrid composites containing 1-8phr kaolin geopolymer filler was studied upon cyclic deformation (three-point flexion mode) as the temperature is varies. The analysis was determined by dynamic mechanical analysis (DMA) at frequency of 1.0Hz. The results then expressed in storage modulus (E�), loss modulus (E�) and damping factor (tan d) as function of temperature from 40 oC to 130oC. Overall results indicated that E�, E�� and Tg increased considerably by incorporating optimum 1phr kaolin geopolymer in epoxy organo-montmorillonite hybrid composites.

Mechanical and Morphological Properties of Sisal/Glass Fiber-Polypropylene Composites

2008 ◽  
Vol 47-50 ◽  
pp. 486-489 ◽  
Author(s):  
Kasama Jarukumjorn ◽  
Nitinat Suppakarn ◽  
Jongrak Kluengsamrong
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Natural Fiber ◽  
Hybrid Composites ◽  
Weight Ratio ◽  
Morphological Properties ◽  
Fiber Reinforced ◽  
Polypropylene Composites ◽  
Specific Strength ◽  
Fiber Reinforced Polymer Composites

Natural fiber reinforced polymer composites became more attractive due to their light weight, high specific strength, biodegradability. However, some limitations e.g. low modulus, poor moisture resistance were reported. The mechanical properties of natural fiber reinforced composites can be improved by hybridization with synthetic fibers such as glass fiber. In this research, mechanical properties of short sisal-PP composites and short sisal/glass fiber hybrid composites were studied. Polypropylene grafted with maleic anhydride (PP-g-MA) was used as a compatibilizer to enhance the compatibility between the fibers and polypropylene. Effect of weight ratio of sisal and glass fiber at 30 % by weight on the mechanical properties of the composites was investigated. Morphology of fracture surface of each composite was also observed.

scholarly journals Optimization of Sisal Fiber, Glass Fiber and Alumina- Based Hybrid Composite for Flexural Strength Using Taguchi Technique

2021 ◽  
Vol 9 (10) ◽  
pp. 474-483
Author(s):  
Veenapani R
Keyword(s):  
Flexural Strength ◽  
Glass Fiber ◽  
Hybrid Composite ◽  
Hybrid Composites ◽  
The Other ◽  
Synthetic Fiber ◽  
Sisal Fiber ◽  
Taguchi Technique ◽  
Fiber Glass ◽  
Main Effect

Abstract: In the current study, flexural strength of combination of natural and synthetic fiber with particle filled hybrid composites have been studied. The flexural strength of the hybrid composite mainly depends on the proportion of the sisal fiber weight, glass fiber weight and alumina weight. Taguchi technique has been applied to find the optimized parameters of the developed hybrid composites. Results were obtained for the L9 orthogonal combination from experimentation. The results were analysed with the help of Signal/Noise (S/N) Ratio, Main effect plot and Analysis of variance (ANOVA) using Mini Tab 19. Regression equation are developed for all three reinforcements separately. From the current study it was observed that the flexural strength of the hybrid composite mainly depends on the sisal fiber precent that the other two reinforcements. Based on the experimental observations the maximum ultimate flexural strength was found to be 145.97 MPa for optimised input parameters as 20% of sisal fiber, 20% of glass fiber and 2% of alumina. Keywords: Taguchi technique, ANOVA, Flexural strength, Sisal fiber, Glass Fiber, Alumina

scholarly journals Evaluation of some Properties of Polyester Based Hybrid Composites Produced From Luffa-Bananna Fibres

2019 ◽  
Vol 1 ◽  
pp. 265-274
Author(s):  
K K Ikpambese ◽  
S Aye ◽  
A W Onuh
Keyword(s):  
Water Absorption ◽  
Interior Design ◽  
Hybrid Composites ◽  
Raw Materials ◽  
Loss Modulus ◽  
Maximum Level ◽  
Dynamic Mechanical Properties ◽  
Damping Factor ◽  
Dynamic Mechanical ◽  
Increasing Temperature

This study presents the evaluation of the mechanical, physical and dynamic mechanical properties of luffa-banana fibre reinforced polyester hybrid composites. The luffa fibre and banana fibres were extracted from luffa plant and banana stem respectively by manual stripping into strands. The luffa and banana fibres were then blended in the ratio of 50:50 for the production of the hybrid composites using hand lay-up method. Polyester-resin was used as binder and the percentages of luffa-banana fibres used were 3, 5, 6, and 9 %. The tensile strength, impact strength, flexural strength, density, water absorption, and the dynamic mechanical analysis (DMA) (storage modulus, loss modulus damping factor) of the produced luffa-banana hybrid composites were evaluated. The results of the density and water absorption obtained varied from 0.84-1.23 g/cm3 and 0 - 0.35 % respectively. The tensile and impact strengths (3.46 - 9.27 MPa and 0.66-3.26 J/cm2) of the produced hybrid composites were observed to increase with increasing fibre content from 3 - 6 % and decreased at 9 %. The results of DMA revealed that loss modulus of the hybrid composites and pure polyester were found to increase with increasing temperature up to glass transition temperature and then decreased. The damping factor was observed to increase with increasing temperature and goes at maximum level in transition region and while decreasing the in rubbery region. The properties of the produced hybrid luffa-banana composites showed that luffa and banana fibres can be used in synergy as raw materials for composites manufacture. As the properties evaluated were in agreement with standard composites used as interior design of cars.

Flexural and Impact Properties of 2D and 3D Jute/GF/Epoxy Hybrid Composite Materials

2015 ◽  
Vol 766-767 ◽  
pp. 178-182
Author(s):  
N.R.R. Anbusagar ◽  
K. Palanikumar ◽  
R. Mohanarangan ◽  
P. Sengottuvel
Keyword(s):  
Flexural Strength ◽  
Glass Fiber ◽  
Hybrid Composite ◽  
Hybrid Composites ◽  
Fiber Composite ◽  
Three Dimensional ◽  
Glass Fiber Composite ◽  
Nylon Fiber ◽  
2D And 3D ◽  
The Impact

In order characterize the outstanding performance of the three dimensional (3D) hybrid composites, the charpy and flexural test has been carried out. 3D fiber structures have been achieved by using hand lay-up process and machine stitching method. Materials for hand lay-up and machine stitching process were glass fiber, jute fiber, and epoxy resin and nylon fiber respectively. Two dimensional (2D) glass fiber composite and 2D hybrid composite with the same stacking sequence as three dimensional (3D) counterparts have also been fabricated for the comparison of impact and flexural strength. The impact strength of 3D hybrid composite was increased (5-10%) compared with that 2D glass fiber and 2D hybrid composites. The flexural strength and modulus of 3D hybrid composite were increased (5-10%) compared with that of 2D hybrid composites.

Sign in / Sign up

Export Citation Format

Share Document