scholarly journals Experimental study of tribological and mechanical properties of TiN coating on AISI 52100 bearing steel

2018 ◽  
Vol 10 (9) ◽  
pp. 168781401880288 ◽  
Author(s):  
Ghulam Moeen Uddin ◽  
Awais Ahmad Khan ◽  
Muhammad Ghufran ◽  
Zia-ur-Rehman Tahir ◽  
Muhammad Asim ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Surface Roughness ◽  
Tribological Properties ◽  
Coating Thickness ◽  
Physical Vapor Deposition ◽  
Substrate Surface ◽  
Bearing Steel ◽  
Tin Coating ◽  
Aisi 52100 ◽  
Substrate Surface Roughness

The surface coating is one of the novel approaches to enhance the performance and durability of the mechanical components by decreasing the wear and friction among two interacting bodies. In this study, tribological and mechanical properties of titanium nitride (TiN) coatings were investigated on the AISI 52100 bearing steel deposited by low-temperature physical vapor deposition system. Surface morphology and elemental composition of the TiN coating were analyzed by scanning electron microscope and energy-dispersive X-ray spectrum, respectively. Substrate surface roughness and coating thickness of TiN were varied for correlative analysis among adhesion, mechanical, and tribological properties. Scratch and tribo tests were performed for evaluating the adhesion and tribological properties, respectively. Samples having the substrate surface roughness (0.2 ± 0.05 µm) and the coating thickness of more than 2.83 µm presented relatively better adhesion, wear resistance, and lower coefficient of friction of the TiN coating.

scholarly journals Effect of Substrate Surface Roughness on the Tribological Properties of DLC-H Coatings on Tappet Valve

2021 ◽  
Vol 43 (2) ◽  
pp. 189-199
Author(s):  
F.O. Kolawole ◽  
S.K. Kolawole ◽  
L.B. Varela ◽  
A. Kraszczuk ◽  
M.A. Ramirez ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Tribological Properties ◽  
Substrate Surface ◽  
Substrate Surface Roughness

scholarly journals Influence of Applied Bias Voltage on the Composition, Structure, and Properties of Ti:Si-Codoped a-C:H Films Prepared by Magnetron Sputtering

2014 ◽  
Vol 2014 ◽  
pp. 1-7 ◽  
Author(s):  
Jinlong Jiang ◽  
Qiong Wang ◽  
Yubao Wang ◽  
Zhang Xia ◽  
Hua Yang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Surface Roughness ◽  
Magnetron Sputtering ◽  
Bias Voltage ◽  
Tribological Properties ◽  
Structure And Properties ◽  
Applied Bias ◽  
Applied Bias Voltage ◽  
Methane Mixture ◽  
Composition Structure

The titanium- and silicon-codoped a-C:H films were prepared at different applied bias voltage by magnetron sputtering TiSi target in argon and methane mixture atmosphere. The influence of the applied bias voltage on the composition, surface morphology, structure, and mechanical properties of the films was investigated by XPS, AFM, Raman, FTIR spectroscopy, and nanoindenter. The tribological properties of the films were characterized on an UMT-2MT tribometer. The results demonstrated that the film became smoother and denser with increasing the applied bias voltage up to −200 V, whereas surface roughness increased due to the enhancement of ion bombardment as the applied bias voltage further increased. The sp3carbon fraction in the films monotonously decreased with increasing the applied bias voltage. The film exhibited moderate hardness and the superior tribological properties at the applied bias voltage of −100 V. The tribological behaviors are correlated to the H/E or H3/E2ratio of the films.

EFFECT OF SURFACE ROUGHNESS ON THE ADHESIVE AND TRIBOLOGICAL CHARACTERISTICS OF DLC COATING PREPARED ON Co-Cr-Mo ALLOY

2002 ◽  
Vol 16 (06n07) ◽  
pp. 952-957 ◽  
Author(s):  
D. Sheeja ◽  
B. K. Tay ◽  
H. M. Lam ◽  
S. K. Ng
Keyword(s):  
Surface Roughness ◽  
Life Span ◽  
Substrate Surface ◽  
Resistance Coefficient ◽  
Metal Alloy ◽  
Deposition Condition ◽  
Dlc Coatings ◽  
Dlc Coating ◽  
Short Life Span ◽  
Substrate Surface Roughness

The Co-Cr-Mo alloy is extensively used for tribological applications, including orthopaedic components in total joint replacements. High quality diamond-like carbon (DLC) coatings on metal/alloy substrates are of great interest as they are able to protect them from severe wear and thus prolong the life span of the component. Since the roughness of the metal/alloy varies depending on the applications, a study has been carried out to investigate the effect of substrate surface roughness on the microstructure, sliding life, wear-resistance, coefficient of friction, adhension and hardness of DLC coatings prepared on Co-Cr-Mo alloy substrates under the same deposition condition. The microstructure of the films studied using Raman spectroscopy suggests that the film prepared on a smoother surface contains slightly higher fraction of sp 3 bonded carbon atoms. The characterization using a pin-on-disk tribometer reveals that, the film prepared on the roughest sample (Ra ~ 0.06 μm) exhibits a very short life span of about 20 cycles compared to the film that is prepared on a relatively smoother surface (Ra ~ 0.02 μm), which exhibits a life span of about 340,000 cycles. In order to investigate the origin of this improved property of the DLC film on the smoother surface, adhesive strength and hardness of the films were studied by using a micro-scratch tester and a Nano-indenter, respectively. The results suggest that the film prepared on the smoother surface exhibits better adhesion (higher critical load) and relatively higher hardness.

Determination of Spread Activation Energy and Assessment of Wetting Behavior of Solders on Metallic Substrates

2010 ◽  
Vol 132 (4) ◽  
Author(s):  
K. N. Prabhu ◽  
G. Kumar
Keyword(s):  
Surface Roughness ◽  
Operating Temperature ◽  
Substrate Surface ◽  
Substrate Material ◽  
Metallic Substrates ◽  
Wetting Behavior ◽  
Substrate Surface Roughness ◽  
Exponential Power ◽  
Kinetics Of

The effects of substrate material, substrate surface roughness, and operating temperature on the wetting behavior of Sn–37Pb, Sn–3.5Ag, and Sn–9Zn eutectic solders on metallic substrates were investigated. Solder spreading kinetics was successfully represented by the exponential power law (EPL): ϕ=exp(−Kτn). The EPL parameter K has the significance of accelerating the kinetics of relaxation while the parameter n represents the resistance to spreading process (spread resistance parameter). EPL parameters exhibited a decreasing trend with an increase in surface roughness. Estimated activation energies for solder spreading were found to be in between those reported for inert and highly reactive spreading systems.

Sign in / Sign up

Export Citation Format

Share Document