scholarly journals Functional properties of protein isolates from camelina (Camelina sativa (L.) Crantz) and flixweed (sophia, Descurainis sophia L.) seed meals

2021 ◽  
Vol 3 (1) ◽  
Author(s):  
Na Thi Ty Ngo ◽  
Fereidoon Shahidi

AbstractCamelina and flixweed (sophia) seed protein isolates were prepared using both the conventional extraction and ultrasonic-assisted extraction methods at 40 kHz for 20 min, and their functional properties investigated. SDS-PAGE showed that both ultrasound-assisted and conventional extractions resulted in a similar protein profile of the extract. The application of ultrasound significantly improved protein extraction/content and functional properties (water holding capacity, oil absorption capacity, emulsifying foaming properties, and protein solubility) of camelina protein isolate and sophia protein isolate. The water-holding and oil absorption capacities of sophia protein isolate were markedly higher than those of camelina protein isolate. These results suggest that camelina protein isolate and sophia protein isolate may serve as natural functional ingredients in the food industry. Graphical Abstract

2014 ◽  
Vol 881-883 ◽  
pp. 766-775 ◽  
Author(s):  
Dan Wu ◽  
Wei Hong Min ◽  
Jing Sheng Liu ◽  
Li Fang ◽  
Hong Mei Li ◽  
...  

The functional properties of protein isolate and major protein fractions prepared from Changbai Mountain pine nuts were investigated. Albumin, globulin, glutelin, and protein isolates were obtained after the Osborne method and alkaline dissolution and acid precipitation, and protein contents of the fractions are 48.02%, 81.93%, 83.02%, and 89.69%, respectively. For the sulfhydryl contents, albumin is the highest, and glutelin is the lowest. In a disulphide bond, the protein isolate content is the highest with a value of 28.74 μmol/g, and the glutelin content is the lowest with the value of 13.46 μmol/g. For the four kinds of proteins, the essential amino acids in percentage of total amino acids are 31.13%, 34.22%, 30.30%, and 34.54%, respectively. The pH dependent protein solubility profile reveals that the minimum solubility is at pH 5.0, which corresponds to the isoelectric point. Protein isolate has the minimum water absorption capacity with a value of 0.59 ml/g. On the other hand, albumin has the minimum oil absorption capacity with a value of 2.11 ml/g. The emulsifying activity and stability and the foaming activity and stability increased with increasing concentration of four kinds of proteins. SDS-PAGE results showed that these four kinds of proteins have different molecules.


2020 ◽  
Vol 12 (1) ◽  
pp. 77-83 ◽  
Author(s):  
Muhammad Elsayed Elsorady

Flaxseed protein isolate (FPI) and sesame protein isolate (SPI) were extracted from flaxseed and sesame cake as by-products, and their functional properties (water holding and fat absorption capacities, bulk density, least gelling concentration, solubility, and emulsifying properties) were determined. Bulk density of the SPI (0.162 g/ml) was lower than that of the FPI (0.175 g/ml). The water absorption capacity of the FPI (305.66%) was higher than that of the SPI (288.93%). The oil absorption capacity and least gelling capacity of the FPI and SPI were 127.48, 3.6, 134.39, and 5%, respectively. The least solubility occurred at pH 4.0 and it was 24.54, 9.56% for FPI and SPI, respectively. Levels of pH and salt concentrations were used as dependent variables for the characterization of emulsifying capacity, activity, and emulsion stability, as well as foaming capacity and foam stability. The addition of NaCl at concentrations up to 1.0 M improved these characteristics. The SPI and FPI had a minimum emulsion capacity (74.54 and 100.20 ml oil/g protein, respectively) and a minimum foam capacity (14.25 and 17.35 %, respectively) at pH 4. The FPI and SPI were found to be highly soluble at acidic and alkaline pH and their emulsifying and foaming properties were high. Moreover, their bulk density, water absorption, and fat absorption capacities and least gelling capacity properties were good. Therefore, the FPI and SPI can be used in food formulation systems.


2019 ◽  
Vol 15 (3-4) ◽  
Author(s):  
Cuiping Yu ◽  
Fan Wu ◽  
Yue Cha ◽  
Henan Zou ◽  
Yingnan Guo ◽  
...  

AbstractStructural and functional changes in ultrasonicated oyster protein isolates (OPI) were investigated. Ultrasound treatments were carried out with probe (20 kHz) at 200, 400 and 600 W for 15 and 30 min. The results showed that functional properties of OPI significantly improved after sonication. Absolute zeta potential and protein solubility increased by 18.40 mV and 82.5 % at 600 W for 15 min. Oil holding capacity, emulsifying activity index, emulsion stability index, foaming ability and foaming stability increased by 300 %, 15.23 m2/g, 9.24 min, 23.9 % and 14.8 % at 600 W for 30 min. However, ultrasound treatment significantly (P < 0.05) decreased particle size and water holding capacity. The conformation of OPI became stretched and unfolded after sonication. Functional improvements resulted from stretched and unfolded conformation and reduction of particle size. Controlled condition of ultrasound can produce OPI with distinct structural and functional properties, which could meet the complex needs of manufactured food products in food industry, but further study is needed to understand the specific mechanism.


2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Natalia del Carmen Espinosa-Murillo ◽  
José Armando Ulloa ◽  
Judith Esmeralda Urías-Silvas ◽  
Petra Rosas-Ulloa ◽  
José Carmen Ramírez-Ramírez ◽  
...  

Abstract A protein isolate from passion fruit seeds (PFSPI) obtained by alkaline extraction and isoelectric precipitation was treated with sonication for 15 and 30 min at 40 kHz to evaluate its impact on the physicochemical and functional properties. The PFSPI had a purity of 96.21% protein, with albumins being the main fraction (75.66%). Ultrasound increased the bulk density (ρ) of PFSPI by 13.3% and the formation a more porous structure by a greater separation between particles. Protein solubility of PFSPI in the range of pH 2–12 sonicated for 15 and 30 min, increased on average 5.21 and 9.86%, respectively, in comparison with the control. PFSPI foaming properties were influenced by pH and sonication time, achieving up to 577%, while the minimum gelling concentration was reduced from 4 to 2% at pH 7. Therefore, sonication treatment improved some functional properties of PFSPI for its potential use as a food ingredient.


2019 ◽  
Vol 15 (3) ◽  
pp. 228-233
Author(s):  
Prabhavathi Supriya ◽  
Kandikere R. Sridhar

Background: Utilization of wild legumes has received prime importance in the recent past to compensate the scarcity of protein-rich foods as well as to tackle the protein energy malnutrition. Ripened split beans of Canavalia maritima devoid of seed coat and testa serve as traditional nutraceutical source for the coastal dwellers of Southwest India. Objective: The present study projects proximal and functional attributes of uncooked and cooked ripened split beans of C. maritima to be used in the preparation of functional foods. Methods: Proximal properties (moisture, crude protein, total lipids, crude fibre, carbohydrates and calorific value) and functional properties (protein solubility, gelation capacity, water-absorption, oilabsorption, emulsion qualities and foam qualities) of split beans were evaluated by standard methods. Results: Cooking did not significantly changed the crude protein, total lipids, ash, carbohydrates and calorific value, while it significantly increased the crude fibre. The protein solubility, water-absorption capacity, foam capacity and foam stability were significantly higher in uncooked than cooked beans. The cooked beans were superior to uncooked beans in least gelation concentration, low oil-absorption capacity, emulsion activity and emulsion stability. Conclusion: The functional properties of split bean flours were influenced by the proximal components like crude protein, total lipids and crude fibre. The energy-rich ripened split beans of C. maritima can serve as a new potential source for production of value added functional foods owing to their rich protein, rich carbohydrates, low-lipid and potential bioactive attributes.


Food Research ◽  
2021 ◽  
Vol 5 (4) ◽  
pp. 145-152
Author(s):  
M. Hasmadi ◽  
M. Merlynda ◽  
A.H. Mansoor ◽  
I. Salwa ◽  
M.K. Zainol ◽  
...  

This study aimed to determine the proximate compositions and functional properties of sweet potato flour from different varieties cultivated in Sabah, Malaysia, namely Jepun, Kairot and Kaladi. The results showed that the moisture content of all flour samples was below 14%. The fat and protein content of Jepun sweet potato variety were significantly different (p<0.05) as compared with Kairot and Kaladi sweet potato varieties. The ash and dietary fibre content of Kairot sweet potato flour were higher (p<0.05) compared to Jepun and Kaladi flours. In addition, Kaladi sweet potato had the highest carbohydrate content (82%). There were significant differences (p<0.05) in the values of L*, a* and b* for all sweet potato flours. The Jepun sweet potato flour had the highest foaming capacity, water absorption capacity, oil absorption capacity, swelling power and viscosity. Rapid Visco analyser revealed that significant differences were observed for pasting parameters such as peak viscosity, trough viscosity, breakdown viscosity, final viscosity and setback viscosity. The gelatinisation properties showed that Kairot sweet potato flour had the highest onset temperature, conclusion temperature and enthalpy while Kaladi sweet potato flour had the highest peak temperature.


2015 ◽  
Vol 1 (2) ◽  
pp. 67
Author(s):  
Haq Nawaz ◽  
Muhammad Aslam Shad ◽  
Rabia Mehmood ◽  
Tanzila Rehman ◽  
Hira Munir

<p>Functional properties such as protein solubility, swelling capacity, water holding capacity, gelling ability, bulk density and foaming capacity of flours of some commonly used cereals and legume (wheat, refined wheat, maize and chickpea) and their blends were studied. Blends of flours were prepared by mixing equal proportions of selected floors. Statistically significant difference  in studied functional properties except bulk density was observed among cereal flours and their blends. Chickpea flour was found to possess comparatively high water holding capacity, protein solubility index and swelling capacity. The functional properties of maize and wheat flours were found to be improved when blended with chickpea. Chickpea flour and its blends with cereal flours were found to possess good functional score and suggested as favorable candidates for use in the preparation of viscous foods and bakery products. The data provide guidelines regarding the improvement in functional properties of economically favorable cereal flours.<strong></strong></p>


2020 ◽  
Vol 45 (3) ◽  
Author(s):  
K. O. Soetan ◽  
A. A. Adeola

Underutilized and neglected legumes have numerous nutritional potentials with great contributions to food security but they are usually excluded from research and development agenda. This study evaluates the nutritional and functional properties of six different underutilized and neglected legumes; Lima bean (LB) (Phaseolus lunatus) (2006-009), Bambara groundnut (BG) (Vigna subterranea) (TVSU- 1482), winged bean (WB) (Psophocarpus tetragonolobus) (Tpt-48), jack bean (JB) (Canavalia ensiformis) (Tce-4), sword bean (SB) (Canavalia gladiata) (Tcg-4) and African yam bean (AYB) (Sphenostylis stenocarpa) (TSS-95) from the Genetic Resources Unit (GRU), International Institute of Tropical Agriculture (IITA), Ibadan, Oyo State, Nigeria. Nutritional and functional properties were evaluated using proximate composition, mineral analyses and functional properties like bulk density, water absorption capacity, oil absorption capacity, emulsion capacity and dispersibility. All the procedures were carried out using standard protocols. Statistical analysis was done using descriptive statistics. Results of proximate analysis showed that crude protein ranged from18.88 0.15%(WB) to 26.60±0.14%(AYB), crude fat ranged from 1.84 0.02% (JB) to 6.39 0.03% (BG), crude fibre ranged from 3.70 ±0.00% (AYB) to 5.04 0.03% (SB), ash ranged from 3.10 ± 0.14% (AYB) to 4.66 0.02% (LB), nitrogen free extract ranged from 55.60 0.04% (SB) to 62.97 0.12% (WB), moisture content ranged from 5.75 0.48% (AYB) to 10.77 0.03% (JB), dry matter ranged from 89.23 0.03% (JB) to 94.25 ± 0.488% (AYB) and gross energy ranged from 4.39 0.003 kcal/g (SB) to 4.66 0.00 (BG). Mineral content results revealed that calcium varied from 0.14 0.000% (LB) to 0.23 0.0003% (AYB), phosphorus varied from 0.20 0.0001% (AYB) to 0.38 0.00% (BG), sodium varied from 0.12 0.00% (LB and WB) to 0.35 0.0006% (AYB), potassium varied from 0.69 0.00% (LB) to 1.12 0.00% (BG), magnesium varied from 0.15 0.0002% (AYB) to 0.27 0.000% (BG) and iron varied from 44.84 0.03 (mg/g) (WB) to 80.98 0.0007(mg/g) (AYB). Results of functional properties showed that bulk density ranged from 0.45±0.04 g/mL (WB) to 0.77±0.08 g/mL (SB), water absorption capacity ranged from 168.33±0.03 g/100g (LB) to 183.62±0.01 g/100g (SB), oil absorption capacity ranged from 146.54 ±0.02 g/100g (LB) to 161.55±0.02 g/100g (JB), emulsion capacity ranged from 79.67 ±0.02 g/100g (LB) to 89.46±0.02 g/100g (SB) and dispersibility ranged from81.0±1.41%(SB) to 86.5±0.71% (BG). The study concluded that all the underutilized legumes have varying nutritional and functional properties, which should be exploited for nutritional benefits and industrial applications, as a solution to the problem of food shortage, especially in the developing countries.


Foods ◽  
2020 ◽  
Vol 9 (12) ◽  
pp. 1754
Author(s):  
Davide De Angelis ◽  
Aleksei Kaleda ◽  
Antonella Pasqualone ◽  
Helen Vaikma ◽  
Martti Tamm ◽  
...  

Pea protein dry-fractionated (PDF), pea protein isolated (PIs), soy protein isolated (SIs) and oat protein (OP) were combined in four mixes (PDF_OP, PIs_OP, PDF_PIs_OP, SIs_OP) and extruded to produce meat analogues. The ingredients strongly influenced the process conditions and the use of PDF required higher specific mechanical energy and screw speed to create fibrous texture compared to PIs and SIs. PDF can be conveniently used to produce meat analogues with a protein content of 55 g 100 g−1, which is exploitable in meat-alternatives formulation. PDF-based meat analogues showed lower hardness (13.55–18.33 N) than those produced from PIs and SIs (nearly 27 N), probably due to a more porous structure given by the natural presence of carbohydrates in the dry-fractionated ingredient. PDF_OP and PIs_PDF_OP showed a significantly lower water absorption capacity than PIs OP and SIs_OP, whereas pea-based extrudates showed high oil absorption capacity, which could be convenient to facilitate the inclusion of oil and fat in the final formulation. The sensory evaluation highlighted an intense odor and taste profile of PDF_OP, whereas the extrudates produced by protein isolates had more neutral sensory characteristics. Overall, the use of dry-fractionated protein supports the strategies to efficiently produce clean-labeled and sustainable plant-based meat analogues.


2015 ◽  
Vol 4 (5) ◽  
pp. 143 ◽  
Author(s):  
Fatemeh Zare ◽  
Valérie Orsat ◽  
Joyce I. Boye

The objective of this study was to explore the use of pulse ingredients in the development of orange juice and apple juice supplemented beverages. Commercially available pulse ingredients including pea protein (PP), chickpea flour (CPF), lentil flour (LF) and pea fibre (PF) were selected and characterized with respect to specific functional properties (water holding capacity, fat absorption capacity, protein solubility, emulsifying and foaming properties). Apple juice was supplemented with 1-4% pulse ingredients, whereas a supplementation level of 1-2% was used for orange juice. The physical and sensory properties of the supplemented beverages were measured after production and during 3 weeks of refrigerated storage. Sensory attributes for both orange and apple juice supplemented with 1% and 2% pulse ingredients were similar to their respective controls (with and without pectin added). In terms of turbidity, supplementation increased the turbidity of apple juice and orange juice beverages at all levels, in comparison with control and pectin-added control samples. Supplemented samples, showed less satisfactory results in terms of cloud stability and color especially for orange juice beverages in comparison with their respective controls. Overall, while there are some hurdles to be overcome, the results suggest that when used at the 1-2% levels, PP, PF, CPF and LF could serve as potential value-added ingredients for beverage supplementation based on their physical and sensory properties. Further studies are, however, required in this promising area to improve the stability of the final production especially during storage.


Sign in / Sign up

Export Citation Format

Share Document