High‐resolution seismic traveltime tomography incorporating static corrections applied to a till‐covered bedrock environment

Geophysics ◽  
2004 ◽  
Vol 69 (4) ◽  
pp. 1082-1090 ◽  
Author(s):  
Björn Bergman ◽  
Ari Tryggvason ◽  
Christopher Juhlin
Keyword(s):  
High Resolution ◽  
Velocity Model ◽  
Surface Velocity ◽  
Data Set ◽  
Near Surface ◽  
Seismic Processing ◽  
Simultaneous Inversion ◽  
Reflection Seismic ◽  
Static Corrections ◽  
Velocity Variations

A major obstacle in tomographic inversion is near‐surface velocity variations. Such shallow velocity variations need to be known and correctly accounted for to obtain images of deeper structures with high resolution and quality. Bedrock cover in many areas consists of unconsolidated sediments and glacial till. To handle the problems associated with this cover, we present a tomographic method that solves for the 3D velocity structure and receiver static corrections simultaneously. We test the method on first‐arrival picks from deep seismic reflection data acquired in the mid‐ late to 1980s in the Siljan Ring area, central Sweden. To use this data set successfully, one needs to handle a number of problems, including time‐varying, near‐surface velocities from data recorded in winter and summer, several sources and receivers within each inversion cell, varying thickness of the cover layer in each inversion cell, and complex 3D geology. Simultaneous inversion for static corrections and velocity produces a much better image than standard tomography without statics. The velocity model from the simultaneous inversion is superior to the velocity model produced using refraction statics obtained from standard reflection seismic processing prior to inversion. Best results using the simultaneous inversion are obtained when the initial top velocity layer is set to the near‐surface bedrock velocity rather than the velocity of the cover. The resulting static calculations may, in the future, be compared to refraction static corrections in standard reflection seismic processing. The preferred final model shows a good correlation with the mapped geology and the airborne magneticmap.

Overthrust imaging with tomo‐datuming: A case study

Geophysics ◽  
1998 ◽  
Vol 63 (1) ◽  
pp. 25-38 ◽  
Author(s):  
Xianhuai Zhu ◽  
Burke G. Angstman ◽  
David P. Sixta
Keyword(s):  
Velocity Model ◽  
Surface Velocity ◽  
Time Shift ◽  
Lateral Velocity ◽  
Prestack Depth Migration ◽  
Near Surface ◽  
Depth Migration ◽  
Static Corrections ◽  
Velocity Variations ◽  
Kirchhoff Method

Through the use of iterative turning‐ray tomography followed by wave‐equation datuming (or tomo‐datuming) and prestack depth migration, we generate accurate prestack images of seismic data in overthrust areas containing both highly variable near‐surface velocities and rough topography. In tomo‐datuming, we downward continue shot records from the topography to a horizontal datum using velocities estimated from tomography. Turning‐ray tomography often provides a more accurate near‐surface velocity model than that from refraction statics. The main advantage of tomo‐datuming over tomo‐statics (tomography plus static corrections) or refraction statics is that instead of applying a vertical time‐shift to the data, tomo‐datuming propagates the recorded wavefield to the new datum. We find that tomo‐datuming better reconstructs diffractions and reflections, subsequently providing better images after migration. In the datuming process, we use a recursive finite‐difference (FD) scheme to extrapolate wavefield without applying the imaging condition, such that lateral velocity variations can be handled properly and approximations in traveltime calculations associated with the raypath distortions near the surface for migration are avoided. We follow the downward continuation step with a conventional Kirchhoff prestack depth migration. This results in better images than those migrated from the topography using the conventional Kirchhoff method with traveltime calculation in the complicated near surface. Since FD datuming is only applied to the shallow part of the section, its cost is much less than the whole volume FD migration. This is attractive because (1) prestack depth migration usually is used iteratively to build a velocity model, so both efficiency and accuracy are important factors to be considered; and (2) tomo‐datuming can improve the signal‐to‐noise (S/N) ratio of prestack gathers, leading to more accurate migration velocity analysis and better images after depth migration. Case studies with synthetic and field data examples show that tomo‐datuming is especially helpful when strong lateral velocity variations are present below the topography.

Novel strategies for complex foothills seismic imaging — Part 1: Mega-near-surface velocity estimation

2020 ◽  
Vol 8 (3) ◽  
pp. T651-T665
Author(s):  
Yalin Li ◽  
Xianhuai Zhu ◽  
Gengxin Peng ◽  
Liansheng Liu ◽  
Wensheng Duan
Keyword(s):  
Seismic Imaging ◽  
Velocity Model ◽  
Velocity Estimation ◽  
Innovative Approach ◽  
Surface Velocity ◽  
Near Surface ◽  
Depth Migration ◽  
Static Corrections ◽  
Over Time

Seismic imaging in foothills areas is challenging because of the complexity of the near-surface and subsurface structures. Single seismic surveys often are not adequate in a foothill-exploration area, and multiple phases with different acquisition designs within the same block are required over time to get desired sampling in space and azimuths for optimizing noise attenuation, velocity estimation, and migration. This is partly because of economic concerns, and it is partly because technology is progressing over time, creating the need for unified criteria in processing workflows and parameters at different blocks in a study area. Each block is defined as a function of not only location but also the acquisition and processing phase. An innovative idea for complex foothills seismic imaging is presented to solve a matrix of blocks and tasks. For each task, such as near-surface velocity estimation and static corrections, signal processing, prestack time migration, velocity-model building, and prestack depth migration, one or two best service companies are selected to work on all blocks. We have implemented streamlined processing efficiently so that Task-1 to Task-n progressed with good coordination. Application of this innovative approach to a mega-project containing 16 3D surveys covering more than [Formula: see text] in the Kelasu foothills, northwestern China, has demonstrated that this innovative approach is a current best practice in complex foothills imaging. To date, this is the largest foothills imaging project in the world. The case study in Kelasu successfully has delivered near-surface velocity models using first arrivals picked up to 3500 m offset for static corrections and 9000 m offset for prestack depth migration from topography. Most importantly, the present megaproject is a merge of several 3D surveys, with the merge performed in a coordinated, systematic fashion in contrast to most land megaprojects. The benefits of this approach and the strategies used in processing data from the various subsurveys are significant. The main achievement from the case study is that the depth images, after the application of the near-surface velocity model estimated from the megasurveys, are more continuous and geologically plausible, leading to more accurate seismic interpretation.

Imaging permafrost velocity structure using high resolution 3D seismic tomography

Geophysics ◽  
2011 ◽  
Vol 76 (5) ◽  
pp. B187-B198 ◽  
Author(s):  
Kumar Ramachandran ◽  
Gilles Bellefleur ◽  
Tom Brent ◽  
Michael Riedel ◽  
Scott Dallimore
Keyword(s):  
High Resolution ◽  
Velocity Structure ◽  
Velocity Model ◽  
Water Bodies ◽  
Unfrozen Water ◽  
3D Seismic ◽  
Tomographic Inversion ◽  
Near Surface ◽  
First Arrival ◽  
Velocity Variations

A 3D seismic survey (Mallik 3D), covering [Formula: see text] in the Mackenzie Delta area of Canada’s north, was conducted by industry in 2002. Numerous lakes and marine inundation create a complex near-surface structure in the permafrost terrain. Much of the near subsurface remains frozen but significant melt zones exist particularly from perennially unfrozen water bodies. This results in an irregular distribution of permafrost ice creating a complex pattern of low and high frequency near-surface velocity variations which induce significant traveltime distortions in surface seismic data. A high resolution 3D traveltime tomography study was employed to map the permafrost velocity structure utilizing first-arrival traveltimes picked from 3D seismic shot records. Approximately 900,000 traveltime picks from 3167 shots were used in the inversion. Tomographic inversion of the first-arrival traveltimes resulted in a smooth velocity model for the upper 200 m of the subsurface. Ray coverage in the model is excellent down to 200 m providing effective control for estimating velocities through tomographic inversion. Resolution tests conducted through horizontal and vertical checkerboard tests confirm the robustness of the velocity model in detailing small scale velocity variations. Well velocities were used to validate tomographic velocities. The tomographic velocities do not show systematic correlation with well velocities. The velocity model clearly images the permafrost velocity structure in lateral and vertical directions. It is inferred from the velocity model that the permafrost structure in the near subsurface is discontinuous. Extensions of surface water bodies in depth, characterized by low P-wave velocities, are well imaged by the velocity model. Deep lakes with unfrozen water, inferred from the tomographic velocity model, correlate with areas of strong amplitude blanking and frequency attenuation observed in processed reflection seismic stack sections.

An application of full-waveform inversion to land data using the pseudo-Hessian matrix

2016 ◽  
Vol 4 (4) ◽  
pp. T627-T635
Author(s):  
Yikang Zheng ◽  
Wei Zhang ◽  
Yibo Wang ◽  
Qingfeng Xue ◽  
Xu Chang
Keyword(s):  
Hessian Matrix ◽  
Waveform Inversion ◽  
Computational Cost ◽  
Velocity Model ◽  
Surface Velocity ◽  
Full Waveform Inversion ◽  
Data Set ◽  
Near Surface ◽  
Full Waveform ◽  
The Time Domain

Full-waveform inversion (FWI) is used to estimate the near-surface velocity field by minimizing the difference between synthetic and observed data iteratively. We apply this method to a data set collected on land. A multiscale strategy is used to overcome the local minima problem and the cycle-skipping phenomenon. Another obstacle in this application is the slow convergence rate. The inverse Hessian can enhance the poorly blurred gradient in FWI, but obtaining the full Hessian matrix needs intensive computation cost; thus, we have developed an efficient method aimed at the pseudo-Hessian in the time domain. The gradient in our FWI workflow is preconditioned with the obtained pseudo-Hessian and a synthetic example verifies its effectiveness in reducing computational cost. We then apply the workflow on the land data set, and the inverted velocity model is better resolved compared with traveltime tomography. The image and angle gathers we get from the inversion result indicate more detailed information of subsurface structures, which will contribute to the subsequent seismic interpretation.

Full-waveform static corrections using blind channel identification

Geophysics ◽  
2007 ◽  
Vol 72 (4) ◽  
pp. U55-U66 ◽  
Author(s):  
Robbert van Vossen ◽  
Jeannot Trampert
Keyword(s):  
Synthetic Data ◽  
Depth Resolution ◽  
Surface Heterogeneity ◽  
Surface Velocity ◽  
Coherent Noise ◽  
Data Set ◽  
Channel Identification ◽  
Near Surface ◽  
Full Waveform ◽  
Static Corrections

Near-surface wavefield perturbations can be very complex and completely mask the target reflections. Despite this complexity, conventional methods rely on parameterizations characterized by simple time and amplitude anomalies to compensate for these perturbations. Determining and compensating for time shifts is generally referred to as (residual) static corrections, whereas surface-consistent deconvolution techniques deal with amplitude anomalies. We present an approach that uses the full waveform to parameterize near-surface perturbations. Therefore, we refer to this method as waveform statics. Important differences from conventional static corrections are that this approach allows time shifts to vary with frequency and takes amplitude variations directly into account. Furthermore, the procedure is fully automated and does not rely on near-surface velocity information. The waveform static corrections are obtained usingblind channel identification and applied to the recordings using multichannel deconvolution. As a result, the method implicitly incorporates array forming. The developed method is validated on synthetic data and applied to part of a field data set acquired in an area with significant near-surface heterogeneity. The source and receiver responses obtained are strongly correlated to the near-surface conditions and show changes, both in phase and frequency content, along the spread. The application of the waveform statics demonstrates that they not only correct for near-surface wavefield perturbations, but also strongly reduce coherent noise. This results in substantial improvements, both in trace-to-trace coherency and in depth resolution. In addition, the procedure delineates reflection events that are difficult to detect prior to our proposed correction. Based on these results, we conclude that complex near-surface perturbations can be successfully dealt with using the multichannel, full-waveform, static-correction procedure.

Computing near-surface velocity models for S-wave static corrections using raypath interferometry

Geophysics ◽  
2018 ◽  
Vol 83 (3) ◽  
pp. U23-U34
Author(s):  
Raul Cova ◽  
David Henley ◽  
Kristopher A. Innanen
Keyword(s):  
Wave Velocity ◽  
Velocity Model ◽  
P Wave ◽  
Surface Velocity ◽  
S Wave ◽  
Converted Wave ◽  
Near Surface ◽  
Velocity Models ◽  
Consistent Solution ◽  
Static Corrections

A near-surface velocity model is one of the typical products generated when computing static corrections, particularly in the processing of PP data. Critically refracted waves are the input usually needed for this process. In addition, for the converted PS mode, S-wave near-surface corrections must be applied at the receiver locations. In this case, however, critically refracted S-waves are difficult to identify when using P-wave energy sources. We use the [Formula: see text]-[Formula: see text] representation of the converted-wave data to capture the intercept-time differences between receiver locations. These [Formula: see text]-differences are then used in the inversion of a near-surface S-wave velocity model. Our processing workflow provides not only a set of raypath-dependent S-wave static corrections, but also a velocity model that is based on those corrections. Our computed near-surface S-wave velocity model can be used for building migration velocity models or to initialize elastic full-waveform inversions. Our tests on synthetic and field data provided superior results to those obtained by using a surface-consistent solution.

scholarly journals Physics-Based Relationship for Pore Pressure and Vertical Stress Monitoring Using Seismic Velocity Variations

2021 ◽  
Vol 13 (14) ◽  
pp. 2684
Author(s):  
Eldert Fokker ◽  
Elmer Ruigrok ◽  
Rhys Hawkins ◽  
Jeannot Trampert
Keyword(s):  
Pore Pressure ◽  
Seismic Velocity ◽  
Pressure Head ◽  
Groundwater Table ◽  
Surface Velocity ◽  
Seismic Velocities ◽  
Stress Monitoring ◽  
Near Surface ◽  
Velocity Variations ◽  
Velocity Changes

Previous studies examining the relationship between the groundwater table and seismic velocities have been guided by empirical relationships only. Here, we develop a physics-based model relating fluctuations in groundwater table and pore pressure with seismic velocity variations through changes in effective stress. This model justifies the use of seismic velocity variations for monitoring of the pore pressure. Using a subset of the Groningen seismic network, near-surface velocity changes are estimated over a four-year period, using passive image interferometry. The same velocity changes are predicted by applying the newly derived theory to pressure-head recordings. It is demonstrated that the theory provides a close match of the observed seismic velocity changes.

scholarly journals Geophysical imaging of permafrost in the SW Svalbard – the result of two high arctic expeditions to Spitsbergen

2020 ◽  
Author(s):  
Mariusz Majdanski ◽  
Artur Marciniak ◽  
Bartosz Owoc ◽  
Wojciech Dobiński ◽  
Tomasz Wawrzyniak ◽  
...  
Keyword(s):  
Surface Waves ◽  
Active Layer ◽  
High Arctic ◽  
The Arctic ◽  
Seismic Profiles ◽  
Frozen Ground ◽  
Near Surface ◽  
Seismic Processing ◽  
Reflection Seismic ◽  
Sea Coast

<p>The Arctic regions are the place of the fastest observed climate change. One of the indicators of such evolution are changes occurring in the glaciers and the subsurface in the permafrost. The active layer of the permafrost as the shallowest one is well measured by multiple geophysical techniques and in-situ measurements.</p><p>Two high arctic expeditions have been organized to use seismic methods to recognize the shape of the permafrost in two seasons: with the unfrozen ground (October 2017) and frozen ground (April 2018). Two seismic profiles have been designed to visualize the shape of permafrost between the sea coast and the slope of the mountain, and at the front of a retreating glacier. For measurements, a stand-alone seismic stations has been used with accelerated weight drop with in-house modifications and timing system. Seismic profiles were acquired in a time-lapse manner and were supported with GPR and ERT measurements, and continuous temperature monitoring in shallow boreholes.</p><p>Joint interpretation of seismic and auxiliary data using Multichannel analysis of surface waves, First arrival travel-time tomography and Reflection imaging show clear seasonal changes affecting the active layer where P-wave velocities are changing from 3500 to 5200 m/s. This confirms the laboratory measurements showing doubling the seismic velocity of water-filled high-porosity rocks when frozen. The same laboratory study shows significant (>10%) increase of velocity in frozen low porosity rocks, that should be easily visible in seismic.</p><p>In the reflection seismic processing, the most critical part was a detailed front mute to eliminate refracted arrivals spoiling wide-angle near-surface reflections. Those long offset refractions were however used to estimate near-surface velocities further used in reflection processing. In the reflection seismic image, a horizontal reflection was traced at the depth of 120 m at the sea coast deepening to the depth of 300 m near the mountain.</p><p>Additionally, an optimal set of seismic parameters has been established, clearly showing a significantly higher signal to noise ratio in case of frozen ground conditions even with the snow cover. Moreover, logistics in the frozen conditions are much easier and a lack of surface waves recorded in the snow buried geophones makes the seismic processing simpler.</p><p>Acknowledgements               </p><p>This research was funded by the National Science Centre, Poland (NCN) Grant UMO-2015/21/B/ST10/02509.</p>

Sign in / Sign up

Export Citation Format

Share Document