EARTH CONDUCTIVITY DETERMINATIONS EMPLOYING A SINGLE SUPERCONDUCTING COIL

Geophysics ◽  
1976 ◽  
Vol 41 (6) ◽  
pp. 1184-1206 ◽  
Author(s):  
H. F. Morrison ◽  
William Dolan ◽  
Abhijit Dey
Keyword(s):  
Large Scale ◽  
Low Frequency ◽  
High Sensitivity ◽  
Input Resistance ◽  
Measurement Sensitivity ◽  
Superconducting Wires ◽  
Superconducting Coil ◽  
Airborne Electromagnetic ◽  
Earth Conductivity ◽  
Ground Conductivity

A low‐frequency airborne electromagnetic prospecting method has been developed which exploits the inherent low resistance of a superconducting coil. Changes in the input resistance of this coil are monitored in the presence of the conducting earth. The response of the system, the change in the input resistance, is proportional to the quadrature secondary magnetic field at the transmitter, although unlike two‐coil systems, the response does not decrease with increasing frequency. This research has demonstrated that superconducting wires, large scale nonmetallic cryostats, the requisite measurement circuitry, and an appropriate data acquisition system are realizable in a practical flight configuration. The unicoil presents the following significant advantages in electromagnetic prospecting: 1) The measurement sensitivity is not limited by the relative coil motion experienced by two‐coil systems. 2) Ample field strength may be supplied to override ambient noise. 3) Optimum frequencies for specific geologic sections are easily implemented in the range of 10 to 2000 Hz. 4) Maps of ground conductivity may be obtained because precise thermal stability is maintained and the measurement, therefore, is absolute. 5) The point source observation minimizes analytic complexity. 6) The combination of the foregoing features with multiple frequency operation, yields a system of potentially high sensitivity and unprecedented depth of exploration. The unicoil system also possesses some disadvantages: 1) An operational complexity results from the cryogenic procedures required in the field, and 2) the heavy sensor requires a large helicopter.

scholarly journals The AARTFAAC All-Sky Monitor: System Design and Implementation

2016 ◽  
Vol 05 (04) ◽  
pp. 1641008 ◽  
Author(s):  
Peeyush Prasad ◽  
Folkert Huizinga ◽  
Eric Kooistra ◽  
Daniel van der Schuur ◽  
Andre Gunst ◽  
...  
Keyword(s):  
Real Time ◽  
Large Scale ◽  
Low Frequency ◽  
High Sensitivity ◽  
Hierarchical Design ◽  
Minimum Latency ◽  
Analysis Center ◽  
Sky Monitor ◽  
Radio Transients

The Amsterdam–ASTRON Radio Transients Facility and Analysis Center (AARTFAAC) all-sky monitor is a sensitive, real-time transient detector based on the Low Frequency Array (LOFAR). It generates images of the low frequency radio sky with spatial resolution of tens of arcmin, MHz bandwidths, and a time cadence of a few seconds, while simultaneously but independently observing with LOFAR. The image timeseries is then monitored for short and bright radio transients. On detection of a transient, a low latency trigger will be generated for LOFAR, which can interrupt its schedule to carry out follow-up observations of the trigger location at high sensitivity and resolutions. In this paper, we describe our heterogeneous, hierarchical design to manage the 259[Formula: see text]Gbps raw data rate and large scale computing to produce real-time images with minimum latency. We discuss the implementation of the instrumentation, its performance and scalability.

Analysis and design of suitable model structures for activated sludge tanks with circulating flow

1999 ◽  
Vol 39 (4) ◽  
pp. 55-60 ◽  
Author(s):  
J. Alex ◽  
R. Tschepetzki ◽  
U. Jumar ◽  
F. Obenaus ◽  
K.-H. Rosenwinkel
Keyword(s):  
Activated Sludge ◽  
Large Scale ◽  
Wastewater Treatment Plants ◽  
Treatment Plant ◽  
High Sensitivity ◽  
Suitable Model ◽  
Model Structure ◽  
Analysis And Design ◽  
Hydraulic Behaviour ◽  
Model Structures

Activated sludge models are widely used for planning and optimisation of wastewater treatment plants and on line applications are under development to support the operation of complex treatment plants. A proper model is crucial for all of these applications. The task of parameter calibration is focused in several papers and applications. An essential precondition for this task is an appropriately defined model structure, which is often given much less attention. Different model structures for a large scale treatment plant with circulation flow are discussed in this paper. A more systematic method to derive a suitable model structure is applied to this case. Results of a numerical hydraulic model are used for this purpose. The importance of these efforts are proven by a high sensitivity of the simulation results with respect to the selection of the model structure and the hydraulic conditions. Finally it is shown, that model calibration was possible only by adjusting to the hydraulic behaviour and without any changes of biological parameters.

scholarly journals Magnetoelastic Coupling and Delta-E Effect in Magnetoelectric Torsion Mode Resonators

Sensors ◽  
2021 ◽  
Vol 21 (6) ◽  
pp. 2022
Author(s):  
Benjamin Spetzler ◽  
Elizaveta V. Golubeva ◽  
Ron-Marco Friedrich ◽  
Sebastian Zabel ◽  
Christine Kirchhof ◽  
...  
Keyword(s):  
Low Frequency ◽  
High Sensitivity ◽  
Element Model ◽  
Mode Number ◽  
Frequency Change ◽  
General Description ◽  
Resonance Modes ◽  
Field Sensor ◽  
Magnetic Sensitivity ◽  
Bending Modes

Magnetoelectric resonators have been studied for the detection of small amplitude and low frequency magnetic fields via the delta-E effect, mainly in fundamental bending or bulk resonance modes. Here, we present an experimental and theoretical investigation of magnetoelectric thin-film cantilevers that can be operated in bending modes (BMs) and torsion modes (TMs) as a magnetic field sensor. A magnetoelastic macrospin model is combined with an electromechanical finite element model and a general description of the delta-E effect of all stiffness tensor components Cij is derived. Simulations confirm quantitatively that the delta-E effect of the C66 component has the promising potential of significantly increasing the magnetic sensitivity and the maximum normalized frequency change ∆fr. However, the electrical excitation of TMs remains challenging and is found to significantly diminish the gain in sensitivity. Experiments reveal the dependency of the sensitivity and ∆fr of TMs on the mode number, which differs fundamentally from BMs and is well explained by our model. Because the contribution of C11 to the TMs increases with the mode number, the first-order TM yields the highest magnetic sensitivity. Overall, general insights are gained for the design of high-sensitivity delta-E effect sensors, as well as for frequency tunable devices based on the delta-E effect.

scholarly journals Analytical Validation and Clinical Application of Rapid Serological Tests for SARS-CoV-2 Suitable for Large-Scale Screening

Diagnostics ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 869
Author(s):  
Amedeo De Nicolò ◽  
Valeria Avataneo ◽  
Jessica Cusato ◽  
Alice Palermiti ◽  
Jacopo Mula ◽  
...  
Keyword(s):  
Early Diagnosis ◽  
Real Time Pcr ◽  
Large Scale ◽  
High Sensitivity ◽  
Analytical Validation ◽  
Pcr Assay ◽  
Serological Tests ◽  
Flow Test ◽  
Lateral Flow Test ◽  
Large Scale Screening

Recently, large-scale screening for COVID-19 has presented a major challenge, limiting timely countermeasures. Therefore, the application of suitable rapid serological tests could provide useful information, however, little evidence regarding their robustness is currently available. In this work, we evaluated and compared the analytical performance of a rapid lateral-flow test (LFA) and a fast semiquantitative fluorescent immunoassay (FIA) for anti-nucleocapsid (anti-NC) antibodies, with the reverse transcriptase real-time PCR assay as the reference. In 222 patients, LFA showed poor sensitivity (55.9%) within two weeks from PCR, while later testing was more reliable (sensitivity of 85.7% and specificity of 93.1%). Moreover, in a subset of 100 patients, FIA showed high sensitivity (89.1%) and specificity (94.1%) after two weeks from PCR. The coupled application for the screening of 183 patients showed satisfactory concordance (K = 0.858). In conclusion, rapid serological tests were largely not useful for early diagnosis, but they showed good performance in later stages of infection. These could be useful for back-tracing and/or to identify potentially immune subjects.

scholarly journals GASTON: Galactic Star Formation with NIKA2. Evidence for the mass growth of star-forming clumps

2021 ◽  
Author(s):  
A J Rigby ◽  
N Peretto ◽  
R Adam ◽  
P Ade ◽  
M Anderson ◽  
...  
Keyword(s):  
Star Formation ◽  
Large Scale ◽  
Galactic Plane ◽  
High Sensitivity ◽  
High Mass ◽  
Evolutionary Stage ◽  
Mass Star ◽  
Mass Growth ◽  
Star Forming ◽  
Compact Source

Abstract Determining the mechanism by which high-mass stars are formed is essential for our understanding of the energy budget and chemical evolution of galaxies. By using the New IRAM KIDs Array 2 (NIKA2) camera on the Institut de Radio Astronomie Millimétrique (IRAM) 30-m telescope, we have conducted high-sensitivity and large-scale mapping of a fraction of the Galactic plane in order to search for signatures of the transition between the high- and low-mass star-forming modes. Here, we present the first results from the Galactic Star Formation with NIKA2 (GASTON) project, a Large Programme at the IRAM 30-m telescope which is mapping ≈2 deg2 of the inner Galactic plane (GP), centred on ℓ = 23${_{.}^{\circ}}$9, b = 0${_{.}^{\circ}}$05, as well as targets in Taurus and Ophiuchus in 1.15 and 2.00 mm continuum wavebands. In this paper we present the first of the GASTON GP data taken, and present initial science results. We conduct an extraction of structures from the 1.15 mm maps using a dendrogram analysis and, by comparison to the compact source catalogues from Herschel survey data, we identify a population of 321 previously-undetected clumps. Approximately 80 per cent of these new clumps are 70 μm-quiet, and may be considered as starless candidates. We find that this new population of clumps are less massive and cooler, on average, than clumps that have already been identified. Further, by classifying the full sample of clumps based upon their infrared-bright fraction – an indicator of evolutionary stage – we find evidence for clump mass growth, supporting models of clump-fed high-mass star formation.

scholarly journals Experiment Investigation of Bistable Vibration Energy Harvesting with Random Wave Environment

2021 ◽  
Vol 11 (9) ◽  
pp. 3868
Author(s):  
Qiong Wu ◽  
Hairui Zhang ◽  
Jie Lian ◽  
Wei Zhao ◽  
Shijie Zhou ◽  
...  
Keyword(s):  
Renewable Energy ◽  
Energy Harvesting ◽  
Cantilever Beam ◽  
Large Scale ◽  
Low Frequency ◽  
Vibration Energy ◽  
Random Wave ◽  
Periodic Signal ◽  
Vibration Energy Harvesting ◽  
Motion Activity

The energy harvested from the renewable energy has been attracting a great potential as a source of electricity for many years; however, several challenges still exist limiting output performance, such as the package and low frequency of the wave. Here, this paper proposed a bistable vibration system for harvesting low-frequency renewable energy, the bistable vibration model consisting of an inverted cantilever beam with a mass block at the tip in a random wave environment and also develop a vibration energy harvesting system with a piezoelectric element attached to the surface of a cantilever beam. The experiment was carried out by simulating the random wave environment using the experimental equipment. The experiment result showed a mass block’s response vibration was indeed changed from a single stable vibration to a bistable oscillation when a random wave signal and a periodic signal were co-excited. It was shown that stochastic resonance phenomena can be activated reliably using the proposed bistable motion system, and, correspondingly, large-scale bistable responses can be generated to realize effective amplitude enlargement after input signals are received. Furthermore, as an important design factor, the influence of periodic excitation signals on the large-scale bistable motion activity was carefully discussed, and a solid foundation was laid for further practical energy harvesting applications.

scholarly journals Enhanced specificity of clinical high-sensitivity tumor mutation profiling in cell-free DNA via paired normal sequencing using MSK-ACCESS

2021 ◽  
Vol 12 (1) ◽  
Author(s):  
A. Rose Brannon ◽  
Gowtham Jayakumaran ◽  
Monica Diosdado ◽  
Juber Patel ◽  
Anna Razumova ◽  
...  
Keyword(s):  
Cancer Patients ◽  
De Novo ◽  
Low Frequency ◽  
High Sensitivity ◽  
Clinical Analysis ◽  
De Novo Mutation ◽  
Cell Free Dna ◽  
Free Dna ◽  
Somatic Alterations ◽  
Mutation Profiling

AbstractCirculating cell-free DNA from blood plasma of cancer patients can be used to non-invasively interrogate somatic tumor alterations. Here we develop MSK-ACCESS (Memorial Sloan Kettering - Analysis of Circulating cfDNA to Examine Somatic Status), an NGS assay for detection of very low frequency somatic alterations in 129 genes. Analytical validation demonstrated 92% sensitivity in de-novo mutation calling down to 0.5% allele frequency and 99% for a priori mutation profiling. To evaluate the performance of MSK-ACCESS, we report results from 681 prospective blood samples that underwent clinical analysis to guide patient management. Somatic alterations are detected in 73% of the samples, 56% of which have clinically actionable alterations. The utilization of matched normal sequencing allows retention of somatic alterations while removing over 10,000 germline and clonal hematopoiesis variants. Our experience illustrates the importance of analyzing matched normal samples when interpreting cfDNA results and highlights the importance of cfDNA as a genomic profiling source for cancer patients.

scholarly journals A New Hybrid Inversion Method for 2D Nuclear Magnetic Resonance Combining TSVD and Tikhonov Regularization

2021 ◽  
Vol 7 (2) ◽  
pp. 18
Author(s):  
Germana Landi ◽  
Fabiana Zama ◽  
Villiam Bortolotti
Keyword(s):  
Nuclear Magnetic Resonance ◽  
Magnetic Resonance ◽  
Tikhonov Regularization ◽  
Large Scale ◽  
Regularization Parameter ◽  
High Sensitivity ◽  
Inversion Method ◽  
Nmr Relaxometry ◽  
Value Decomposition ◽  
Nuclear Magnetic

This paper is concerned with the reconstruction of relaxation time distributions in Nuclear Magnetic Resonance (NMR) relaxometry. This is a large-scale and ill-posed inverse problem with many potential applications in biology, medicine, chemistry, and other disciplines. However, the large amount of data and the consequently long inversion times, together with the high sensitivity of the solution to the value of the regularization parameter, still represent a major issue in the applicability of the NMR relaxometry. We present a method for two-dimensional data inversion (2DNMR) which combines Truncated Singular Value Decomposition and Tikhonov regularization in order to accelerate the inversion time and to reduce the sensitivity to the value of the regularization parameter. The Discrete Picard condition is used to jointly select the SVD truncation and Tikhonov regularization parameters. We evaluate the performance of the proposed method on both simulated and real NMR measurements.

scholarly journals A Novel Methodology for Adaptive Coordination of Multiple Controllers in Electrical Grids

Mathematics ◽  
2021 ◽  
Vol 9 (13) ◽  
pp. 1474
Author(s):  
Ruben Tapia-Olvera ◽  
Francisco Beltran-Carbajal ◽  
Antonio Valderrabano-Gonzalez ◽  
Omar Aguilar-Mejia
Keyword(s):  
Power Systems ◽  
Power System ◽  
Electric Power ◽  
Large Scale ◽  
Short Circuit ◽  
Dynamic Performance ◽  
Low Frequency ◽  
Electric Power System ◽  
Design Stage ◽  
Positive Interaction

This proposal is aimed to overcome the problem that arises when diverse regulation devices and controlling strategies are involved in electric power systems regulation design. When new devices are included in electric power system after the topology and regulation goals were defined, a new design stage is generally needed to obtain the desired outputs. Moreover, if the initial design is based on a linearized model around an equilibrium point, the new conditions might degrade the whole performance of the system. Our proposal demonstrates that the power system performance can be guaranteed with one design stage when an adequate adaptive scheme is updating some critic controllers’ gains. For large-scale power systems, this feature is illustrated with the use of time domain simulations, showing the dynamic behavior of the significant variables. The transient response is enhanced in terms of maximum overshoot and settling time. This is demonstrated using the deviation between the behavior of some important variables with StatCom, but without or with PSS. A B-Spline neural networks algorithm is used to define the best controllers’ gains to efficiently attenuate low frequency oscillations when a short circuit event is presented. This strategy avoids the parameters and power system model dependency; only a dataset of typical variable measurements is required to achieve the expected behavior. The inclusion of PSS and StatCom with positive interaction, enhances the dynamic performance of the system while illustrating the ability of the strategy in adding different controllers in only one design stage.

scholarly journals Optimizing the Frequency Capping: A Robust and Reliable Methodology to Define the Number of Ads to Maximize ROAS

2021 ◽  
Vol 11 (15) ◽  
pp. 6688
Author(s):  
Jesús Romero Leguina ◽  
Ángel Cuevas Rumin ◽  
Rubén Cuevas Rumin
Keyword(s):  
High Frequency ◽  
Large Scale ◽  
Low Frequency ◽  
Digital Marketing ◽  
Optimal Frequency ◽  
Novel Technique ◽  
Maximum Threshold

The goal of digital marketing is to connect advertisers with users that are interested in their products. This means serving ads to users, and it could lead to a user receiving hundreds of impressions of the same ad. Consequently, advertisers can define a maximum threshold to the number of impressions a user can receive, referred to as Frequency Cap. However, low frequency caps mean many users are not engaging with the advertiser. By contrast, with high frequency caps, users may receive many ads leading to annoyance and wasting budget. We build a robust and reliable methodology to define the number of ads that should be delivered to different users to maximize the ROAS and reduce the possibility that users get annoyed with the ads’ brand. The methodology uses a novel technique to find the optimal frequency capping based on the number of non-clicked impressions rather than the traditional number of received impressions. This methodology is validated using simulations and large-scale datasets obtained from real ad campaigns data. To sum up, our work proves that it is feasible to address the frequency capping optimization as a business problem, and we provide a framework that can be used to configure efficient frequency capping values.

Sign in / Sign up

Export Citation Format

Share Document