scholarly journals Protecting Mixed-Signal Technologies against Electrostatic Discharges: Challenges and Protection Strategies from Component to System

2018 ◽  
pp. 76-109
Author(s):  
Patrice Besse
2013 ◽  
Vol 61 (3) ◽  
pp. 691-696 ◽  
Author(s):  
R. Suszynski ◽  
K. Wawryn

Abstract A rapid prototyping method for designing mixed signal systems has been presented in the paper. The method is based on implementation of the field programmable analog array (FPAA) to configure and reconfigure mixed signal systems. A serial algorithmic analog digital converter has been used as an example. Three converter architectures have been selected and implemented FPAA device. To verify and illustrate converters operation and prototyping capabilities, implemented converters have been excited by a sinusoidal signal. Analog sinusoidal excitations, digital responses and sinusoidal waveforms after reconstruction are presented.


2012 ◽  
Vol 1 (1) ◽  
pp. 1-7
Author(s):  
Vadim Geurkov ◽  
◽  
Lev Kirischian ◽  
Keyword(s):  

Author(s):  
Chunyu Zhang ◽  
Lakshmi Vedula ◽  
Shekhar Khandekar

Abstract Latch-up induced during High Temperature Operating Life (HTOL) test of a mixed signal device fabricated with 1.0 μm CMOS, double poly, double metal process caused failures due to an open in aluminum metal line. Metal lines revealed wedge voids of about 50% of the line width. Triggering of latch up mechanism during the HTOL test resulted in a several fold increase of current flowing through the ground metal line. This increase in current resulted in the growth of the wedge voids leading to failures due to open metal lines.


Author(s):  
Julien Goxe ◽  
Béatrice Vanhuffel ◽  
Marie Castignolles ◽  
Thomas Zirilli

Abstract Passive Voltage Contrast (PVC) in a Scanning Electron Microscope (SEM) or a Focused Ion Beam (FIB) is a key Failure Analysis (FA) technique to highlight a leaky gate. The introduction of Silicon On Insulator (SOI) substrate in our recent automotive analog mixed-signal technology highlighted a new challenge: the Bottom Oxide (BOX) layer, by isolating the Silicon Active Area from the bulk made PVC technique less effective in finding leaky MOSFET gates. A solution involving sample preparation performed with standard FA toolset is proposed to enhance PVC on SOI substrate.


Author(s):  
A. M. Shamayev ◽  
M. D. Ozersky

The results of experimental studies of the effect of electron irradiation on K-208 and CMG glasses used for manufacturing protective coatings of solar batteries and thermal control coatings of space vehicles are analyzed. It is shown that the caused electrostatic discharges lead to structural changes in the surfaces of the glasses studied. The goals of further studies of the influence of proton and electronproton effects on the properties of such coatings are outlined. 


Author(s):  
Dori B. Reissman ◽  
Maryann M. D’Alessandro ◽  
Lisa Delaney ◽  
John Piacentino

This chapter describes disaster worker protection strategies and health surveillance activities in terms of temporal phases to address disaster safety management before, during, and after a disaster event. The protective strategies discussed in the chapter integrate assessments of on-scene hazards and health or safety impacts and require pre-event planning and coordination across multiple entities. The chapter also addresses the integration of physical, psychological and behavioral health approaches. The chapter addresses the complexities of hazard assessment and control, worker education and training, worker illness and injury surveillance, and access to healthcare services, along with a box on community preparedness. These activities are performed by diverse groups of occupational and environmental health professionals. Various illustrative examples are presented to describe how basic concepts of protection and medical evaluation are applied in specific situations. The U.S. federal system for protecting disaster rescue and recovery workers is described in detail.


Sign in / Sign up

Export Citation Format

Share Document