Waviness and Roughness in Hydrodynamic Lubrication

1972 ◽  
Vol 186 (1) ◽  
pp. 807-812 ◽  
Author(s):  
K. Tønder ◽  
H. Christensen
Keyword(s):  
Carrying Capacity ◽  
Reynolds Equation ◽  
Hydrodynamic Lubrication ◽  
Load Carrying Capacity ◽  
Slider Bearings ◽  
Load Carrying ◽  
Pressure Ripples

An analysis of the effect of waviness on lubrication is presented. This analysis consists of direct solutions of the Reynolds equation for corrugated slider bearings under various conditions. It is shown how the corrugation wavelength is a major factor, pressure ripples vanishing with increasing corrugation density. It is further shown that at the same time, the load-carrying capacity tends towards that predicted by the authors' statistical roughness theory, the analysis thus constituting a numerical proof of the mathematical soundness of that theory.

Hydrodynamic Lubrication of Finite Slider Bearings: Effect of One Dimensional Film Shape, and Their Computer Aided Optimum Designs

1983 ◽  
Vol 105 (1) ◽  
pp. 48-63 ◽  
Author(s):  
C. Bagci ◽  
A. P. Singh
Keyword(s):  
Numerical Solution ◽  
Carrying Capacity ◽  
Reynolds Equation ◽  
Hydrodynamic Lubrication ◽  
Load Carrying Capacity ◽  
Slider Bearing ◽  
Design Data ◽  
Slider Bearings ◽  
Load Carrying ◽  
Computer Aided

The effect of the film shape on the load carrying capacity of a hydrodynamically lubricated bearing has not been considered an important factor in the past. Flat-faced tapered bearing and the Raileigh’s step bearing of constant film thickness have been the primary forms of film shapes for slider bearing studies and design data developments. This article, by the computer aided numerical solution of the Reynolds equation for two dimensional incompressible lubricant flow, investigates hydrodynamically lubricated slider bearings having different film shapes and studies the effect of the film shape on the performance characteristics of finite bearings; and it shows that optimized bearing with film shapes having descending slope toward the trailing edge of the bearing has considerably higher load carrying capacity than the optimized flat-faced tapered bearing of the same properties. For example the truncated cycloidal film shape yields 26.3 percent higher load carrying capacity for Lz/Lx = 1 size ratio, and 44 percent higher for Lz/Lx = 1/2. The article then presents charts for the optimum designs of finite slider bearings having tapered, exponential, catenoidal, polynomial, and truncated-cycloidal film shapes, and illustrates their use in numerical bearing design examples. These charts also furnish information on flow rate, side leakage, temperature rise, coefficient of friction, and friction power loss in optimum bearings. Appended to the article are analytical solutions for infinitely wide bearings with optimum bearing characteristics. The computer aided numerical solution of the Reynolds equation in most general form is presented by which finite or infinitely wide hydrodynamically or hydrostatically lubricated bearings, externally pressurized or not, can be studied. A digital computer program is made available.

On the study of Rayleigh step slider bearings lubricated with non-Newtonian Rabinowitsch fluid

2017 ◽  
Vol 69 (5) ◽  
pp. 666-672
Author(s):  
N.B. Naduvinamani ◽  
Siddharam Patil ◽  
S.S. Siddapur
Keyword(s):  
Carrying Capacity ◽  
Reynolds Equation ◽  
Maximum Load ◽  
Load Carrying Capacity ◽  
Slider Bearing ◽  
Content Type ◽  
Slider Bearings ◽  
Load Carrying ◽  
Modified Reynolds Equation ◽  
Frictional Coefficients

Purpose Nowadays, the use of Newtonian fluid as a lubricant is diminishing day by day, and the use of non-Newtonian fluids has gained importance. This paper presents an analysis of the static characteristics of Rayleigh step slider bearing lubricated with non-Newtonian Rabinowitsch fluid, which has not been studied so far. The purpose of this paper is to derive the modified Reynolds equation for Rabinowitsch fluids for two regions and to obtain the optimum bearing parameters for the Rayleigh step slider bearings. Design/methodology/approach The governing equations relevant to the problem under consideration are derived. The modified Reynolds equation is derived, and it is found to be highly non-linear and hence small perturbation method is adopted to find solution. Findings From this study it is found that there is an increase in the load-carrying capacity, pressure and frictional coefficients for dilatant fluids as compared to the corresponding Newtonian case. Further, for dilatant lubricants the maximum load-carrying capacity is attained for the slightly larger values of entry region length of Rayleigh step bearing as compared to Newtonian and pseudoplastic lubricants. Originality/value Rabinowitsch fluid is used for the study of lubrication characteristics of Rayleigh step bearings. The author believes that the paper presents these results for the first time.

scholarly journals Thrust Porous Bearing with Rough Surfaces Lubricated by a Rotem-Shinnar Fluid

2016 ◽  
Vol 10 (1) ◽  
pp. 50-55 ◽  
Author(s):  
Anna Walicka ◽  
Edward Walicki
Keyword(s):  
Pressure Distribution ◽  
Carrying Capacity ◽  
Reynolds Equation ◽  
Hydrodynamic Lubrication ◽  
Equations Of Motion ◽  
Squeeze Film ◽  
Load Carrying Capacity ◽  
Porous Bearing ◽  
Load Carrying ◽  
Plastic Fluid

Abstract In the paper the influence of both bearing surfaces roughness and porosity of one bearing surface on the pressure distribution and load-carrying capacity of a thrust bearing surfaces is discussed. The equations of motion of a pseudo-plastic fluid of Rotem-Shinnar, are used to derive the Reynolds equation. After general considerations on the flow in a bearing clearance and in a porous layer using the Morgan-Cameron approximation and Christensen theory of hydrodynamic lubrication the modified Reynolds equation is obtained. The analytical solutions of this equation for the cases of squeeze film bearing and externally pressurized bearing are presented. As a result one obtains the formulae expressing pressure distribution and load-carrying capacity. Thrust radial bearing with squeezed film is considered as a numerical example.

scholarly journals Influence of Wall Porosity and Surfaces Roughness on the Steady Performance of an Externally Pressurized Hydrostatic Conical Bearing Lubricated by a Rabinowitsch Fluid

2017 ◽  
Vol 22 (3) ◽  
pp. 717-737 ◽  
Author(s):  
A. Walicka ◽  
E. Walicki ◽  
P. Jurczak ◽  
J. Falicki
Keyword(s):  
Pressure Distribution ◽  
Carrying Capacity ◽  
Reynolds Equation ◽  
Thrust Bearing ◽  
Hydrodynamic Lubrication ◽  
Equations Of Motion ◽  
Load Carrying Capacity ◽  
Bearing Surface ◽  
Load Carrying ◽  
Conical Bearing

AbstractIn the paper, the influence of both the bearing surfaces roughness as well as porosity of one bearing surface on the pressure distribution and load-carrying capacity of a curvilinear, externally pressurized, thrust bearing is discussed. The equations of motion of a pseudo-plastic Rabinowitsch fluid are used to derive the Reynolds equation. After general considerations on the flow in a bearing clearance and in a porous layer using the Morgan-Cameron approximation and Christensen theory of hydrodynamic lubrication with rough bearing surfaces the modified Reynolds equation is obtained. The analytical solution is presented; as a result one obtains the formulae expressing the pressure distribution and load-carrying capacity. Thrust radial and conical bearings, externally pressurized, are considered as numerical examples.

scholarly journals Two-scale homogenization of hydrodynamic lubrication in a mechanical seal with isotropic roughness based on the Elrod cavitation algorithm

2021 ◽  
pp. 135065012110176
Author(s):  
Yanxiang Han ◽  
Qingen Meng ◽  
Gregory de Boer
Keyword(s):  
Surface Topography ◽  
Carrying Capacity ◽  
Hydrodynamic Lubrication ◽  
Tribological Performance ◽  
Stribeck Curve ◽  
Polar Coordinate System ◽  
Load Carrying Capacity ◽  
Mechanical Seal ◽  
Macro Scale ◽  
Load Carrying

A two-scale homogenization method for modelling the hydrodynamic lubrication of mechanical seals with isotropic roughness was developed and presented the influence of surface topography coupled into the lubricating domain. A linearization approach was derived to link the effects of surface topography across disparate scales. Solutions were calculated in a polar coordinate system derived based on the Elrod cavitation algorithm and were determined using homogenization of periodic simulations describing the lubrication of a series of surface topographical features. Solutions obtained for the hydrodynamic lubrication regime showed that the two-scale homogenization approach agreed well with lubrication theory in the case without topography. Varying topography amplitude demonstrated that the presence of surface topography improved tribological performance for a mechanical seal in terms of increasing load-carrying capacity and reducing friction coefficient in the radial direction. A Stribeck curve analysis was conducted, which indicated that including surface topography led to an increase in load-carrying capacity and a reduction in friction. A study of macro-scale surface waviness showed that the micro-scale variations observed were smaller in magnitude but cannot be obtained without the two-scale method and cause significant changes in the tribological performance.

The Validity of the Reynolds Equation in Modeling Hydrostatic Effects in Gas Lubricated Textured Parallel Surfaces

2005 ◽  
Vol 128 (2) ◽  
pp. 345-350 ◽  
Author(s):  
Y. Feldman ◽  
Y. Kligerman ◽  
I. Etsion ◽  
S. Haber
Keyword(s):  
Carrying Capacity ◽  
Reynolds Equation ◽  
Stokes Equations ◽  
Surface Texturing ◽  
Laser Surface Texturing ◽  
Physical Parameters ◽  
Load Carrying Capacity ◽  
Wide Range ◽  
Load Carrying ◽  
Parallel Surfaces

Microdimples generated by laser surface texturing (LST) can be used to enhance performance in hydrostatic gas-lubricated tribological components with parallel surfaces. The pressure distribution and load carrying capacity for a single three-dimensional dimple, representing the LST, were obtained via two different methods of analysis: a numerical solution of the exact full Navier-Stokes equations, and an approximate solution of the much simpler Reynolds equation. Comparison between the two solution methods illustrates that, despite potential large differences in local pressures, the differences in load carrying capacity, for realistic geometrical and physical parameters, are small. Even at large clearances of 5% of the dimple diameter and pressure ratios of 2.5 the error in the load carrying capacity is only about 15%. Thus, for a wide range of practical clearances and pressures, the simpler, approximate Reynolds equation can safely be applied to yield reasonable predictions for the load carrying capacity of dimpled surfaces.

The Granular Lubricated Journal Bearing: Evidence of Lift Formation

2019 ◽  
Vol 141 (4) ◽  
Author(s):  
Venkata K. Jasti ◽  
Martin C. Marinack ◽  
Deepak Patil ◽  
C. Fred Higgs
Keyword(s):  
Carrying Capacity ◽  
Granular Flow ◽  
High Speed ◽  
Journal Bearing ◽  
Hydrodynamic Lubrication ◽  
Flow Behavior ◽  
Extreme Environments ◽  
Granular Flows ◽  
Load Carrying Capacity ◽  
Load Carrying

This work demonstrates that granular flows (i.e., macroscale, noncohesive spheres) entrained into an eccentrically converging gap can indeed actually exhibit lubrication behavior as prior models postulated. The physics of hydrodynamic lubrication is quite well understood and liquid lubricants perform well for conventional applications. Unfortunately, in certain cases such as high-speed and high-temperature environments, liquid lubricants break down making it impossible to establish a stable liquid film. Therefore, it has been previously proposed that granular media in sliding convergent interfaces can generate load carrying capacity, and thus, granular flow lubrication. It is a possible alternative lubrication mechanism that researchers have been exploring for extreme environments, or wheel-regolith traction, or for elucidating the spreadability of additive manufacturing materials. While the load carrying capacity of granular flows has been previously demonstrated, this work attempts to more directly uncover the hydrodynamic-like granular flow behavior in an experimental journal bearing configuration. An enlarged granular lubricated journal bearing (GLJB) setup has been developed and demonstrated. The setup was made transparent in order to visualize and video capture the granular collision activity at high resolution. In addition, a computational image processing program has been developed to process the resulting images and to noninvasively track the “lift” generated by granular flow during the journal bearing operation. The results of the lift caused by granular flow as a function of journal rotation rate are presented as well.

Stokes Roughness Effects on Hydrodynamic Lubrication. Part II—Effects Under Slip Flow Boundary Conditions

1986 ◽  
Vol 108 (2) ◽  
pp. 159-166 ◽  
Author(s):  
Y. Mitsuya
Keyword(s):  
Flow Regime ◽  
Carrying Capacity ◽  
Stokes Equations ◽  
Hydrodynamic Lubrication ◽  
Slip Flow ◽  
Load Carrying Capacity ◽  
Roughness Effects ◽  
Random Roughness ◽  
Load Carrying ◽  
Flow Effects

Stokes roughness effects on hydrodynamic lubrication are studied in the slip flow regime. Slip flow boundary conditions for Navier-Stokes equations are derived, assuming that the fluid on a surface slips due to the molecular mean free path along the surface, even if the surface is rough. The perturbation method for Navier-Stokes equations, which was derived in Part I of this report, is then applied. Slip flow effects on load carrying capacity and frictional force are numerically clarified for both Stokes and Reynolds roughnesses. In the slip flow regime, second-order quantities induced by Stokes effects, such as flow rate, load carrying capacity, and frictional force are in proportion to the wavenumber squared. This phenomenon relative to the quantities being proportional is also the same as that in the continuum flow regime. As a result of velocity slippage, the load carrying capacity in Stokes roughness is found to decrease more than in Reynolds roughness for incompressible films, while the relationship is reversed for compressible films having a high compressibility number. The simulation of random roughness, which is generated by numerical means, clarifies one important result: the average slip flow effects associated with random Stokes roughness become similar to the slip flow effects in deterministic sinusoidal Stokes roughness, whose wavelength and height are statistically equivalent to those of random roughness. Although attention should be given to the fact that Stokes effects on random roughness demonstrate considerable scattering with the continuum flow, such scattering diminishes with the slip flow.

The Axial Load-Carrying Capacity of Radial Cylindrical Roller Bearings

1970 ◽  
Vol 92 (1) ◽  
pp. 129-134 ◽  
Author(s):  
H. Korrenn
Keyword(s):  
Carrying Capacity ◽  
Hydrodynamic Lubrication ◽  
Experimental Investigations ◽  
Load Carrying Capacity ◽  
Oil Viscosity ◽  
Application Range ◽  
Roller Bearings ◽  
Load Carrying ◽  
Thrust Load ◽  
Cylindrical Roller

Thrust load transmission at the contact areas of roller ends and flanges occurs under conditions of pure sliding. Recent theoretical and experimental investigations showed that with adequately designed roller ends and flanges and with a satisfactory lubricant high thrust loads can be accommodated over a wide speed range with fully hydrodynamic lubrication. The conventional methods used for the determination of the safe thrust load should be revised and supplemented. Oil viscosity should be introduced as an important parameter. Contrary to present opinion the hydrodynamic load-carrying capacity at the flange increases with increasing speed. This new knowledge broadens the application range of radial cylindrical roller bearings.

Sign in / Sign up

Export Citation Format

Share Document