225 A New Method of2 Damage Evaluation with Generation Laser Scanning Method

2013 ◽  
Vol 2013.21 (0) ◽  
pp. _225-1_-_225-3_
Author(s):  
Riu GODA ◽  
Tomonori WATANABE ◽  
Syohei YOSHIYAMA ◽  
Ning HU
Keyword(s):  
Laser Scanning ◽  
New Method ◽  
Damage Evaluation ◽  
Scanning Method

A New Method of Parallel Projective Galvanometer Scanning for Laser Material Processing on Freeform Surfaces

2013 ◽  
Vol 483 ◽  
pp. 9-13 ◽  
Author(s):  
Yu Cao ◽  
Ting Ting Yu ◽  
Xue Lin Hu ◽  
Feng Pin Li
Keyword(s):  
Material Processing ◽  
Laser Scanning ◽  
Dimensional Space ◽  
New Method ◽  
Parallel Projection ◽  
Scanning System ◽  
Laser Material Processing ◽  
Freeform Surfaces ◽  
Scanning Method ◽  
Laser Material

A new method of parallel projection galvanometer scanning (PPGS) is presented, as a low-cost, flexible, trans-scale solution for laser material processing on freeform surfaces. The parallel projection transformation is used for mapping three-dimensional space curves to terraced two-dimensional plane graphics that each one is suitable for traditional galvanometer scanning method. For implementation of the PPGS method, a parallel projective laser scanning system with the combination of galvanometer and telecentric lens is needed, that the laser is directed along the space curve path on freeform surface part without deviation when the x-y axis galvanometer is scanning the mapping graphic path of the parallel projection plane. In practice, the existing 3D galvanometer scan system, "3+2" and rob-scan system are alternative choices in different application situations.

Measurement of erosion state and refractory lining thickness of blast furnace hearth by using three-dimensional laser scanning method

2020 ◽  
Vol 118 (1) ◽  
pp. 106
Author(s):  
Lei Zhang ◽  
Jianliang Zhang ◽  
Kexin Jiao ◽  
Guoli Jia ◽  
Jian Gong ◽  
...  
Keyword(s):  
Blast Furnace ◽  
Laser Scanning ◽  
Refractory Lining ◽  
Three Dimensional ◽  
3D Laser Scanning ◽  
Scanning Method ◽  
Blast Furnace Production ◽  
Severe Erosion ◽  
Residual Thickness ◽  
Minimum Depth

The three-dimensional (3D) model of erosion state of blast furnace (BF) hearth was obtained by using 3D laser scanning method. The thickness of refractory lining can be measured anywhere and the erosion curves were extracted both in the circumferential and height directions to analyze the erosion characteristics. The results show that the most eroded positions located below 20# tuyere with an elevation of 7700 mm and below 24#–25# tuyere with an elevation of 8100 mm, the residual thickness here is only 295 mm. In the circumferential directions, the serious eroded areas located between every two tapholes while the taphole areas were protected well by the bonding material. In the height directions, the severe erosion areas located between the elevation of 7600 mm to 8200 mm. According to the calculation, the minimum depth to ensure the deadman floats in the hearth is 2581 mm, corresponding to the elevation of 7619 mm. It can be considered that during the blast furnace production process, the deadman has been sinking to the bottom of BF hearth and the erosion areas gradually formed at the root of deadman.

scholarly journals DTM-based analysis of the spatial distribution of topolineaments

2020 ◽  
Vol 12 (1) ◽  
pp. 1185-1199
Author(s):  
Mirosław Kamiński
Keyword(s):  
Laser Scanning ◽  
Digital Terrain Model ◽  
Research Area ◽  
Tectonic Structures ◽  
Empirical Bayesian ◽  
Scanning Method ◽  
Empirical Bayesian Kriging ◽  
Terrain Model ◽  
Digital Terrain ◽  
Airborne Laser

AbstractThe research area is located on the boundary between two Paleozoic structural units: the Radom–Kraśnik Block and the Mazovian–Lublin Basin in the southeastern Poland. The tectonic structures are separated by the Ursynów–Kazimierz Dolny fault zone. The digital terrain model obtained by the ALS (Airborne Laser Scanning) method was used. Classification and filtration of an elevation point cloud were performed. Then, from the elevation points representing only surfaces, a digital terrain model was generated. The model was used to visually interpret the course of topolineaments and their automatic extraction from DTM. Two topolineament systems, trending NE–SW and NW–SE, were interpreted. Using the kernel density algorithm, topolineament density models were generated. Using the Empirical Bayesian Kriging, a thickness model of quaternary deposits was generated. A relationship was observed between the course of topolineaments and the distribution and thickness of Quaternary formations. The topolineaments were compared with fault directions marked on tectonic maps of the Paleozoic and Mesozoic. Data validation showed consistency between topolineaments and tectonic faults. The obtained results are encouraging for further research.

INVESTIGATION OF BIAXIAL ELASTIC MODULUS AND CTE OF BaTiO3 FILMS

2009 ◽  
Vol 23 (24) ◽  
pp. 4933-4941
Author(s):  
GUI-FANG HUANG ◽  
WEI-QING HUANG ◽  
LING-LING WANG ◽  
ZHONG XIE ◽  
BING-SUO ZOU ◽  
...  
Keyword(s):  
Elastic Modulus ◽  
Thermal Cycle ◽  
Laser Scanning ◽  
Stress Measurement ◽  
Coefficient Of Thermal Expansion ◽  
Bulk Material ◽  
Good Reliability ◽  
Scanning Method ◽  
As Stress

To develop high-quality film device with good reliability, it is often essential to be able to evaluate the parameters such as stress, the biaxial elastic modulus, and coefficient of thermal expansion (CTE) of film. Based on the stress measurement in situ during the thermal cycle by laser scanning method, two techniques were used to measure the biaxial elastic modulus and CTE of BaTiO 3 films deposited on substrate. The value of the biaxial elastic modulus and CTE for BaTiO 3 films determined from two methods is close, in which the biaxial elastic modulus of BaTiO 3 films is higher than that of corresponding bulk while the CTE of BaTiO 3 films is a little smaller than that of bulk material.

scholarly journals Geodetic and Architectural Inventory of the Historic Wooden Church of St. Szczepan in Mnichów (Poland) in Terms of Safety Assessment of the Geometric Condition of the Structure.

2020 ◽  
Author(s):  
Tomasz Lipecki
Keyword(s):  
Laser Scanning ◽  
Structural Changes ◽  
18Th Century ◽  
Good Condition ◽  
Geometric Condition ◽  
Mining Operations ◽  
Destructive Effect ◽  
Scanning Method ◽  
3D Solid ◽  
The Church

Abstract The article concerns the method of architectural inventory of the historic, wooden church in Mnichów (southern Poland), built in the 18th century. During hundreds of years of operation, structural changes can be seen in it, as well as in objects located above mining operations. The article explains the principles of inventory and describes the applied method of laser scanning, starting from the design to the creation of a 3D solid model of the object, paying particular attention to the analysis based on the created point cloud. Thanks to them, the area and volumes of all rooms were determined, the verticality of columns supporting the church levels was assessed, the floor level and verticality of walls were determined, as well as the shape and level of the roof edges. Based on the research, it can be concluded that the church, as an example of a wooden religious monument, is in good condition. The detected deformations in this range do not have a destructive effect on the current state of the object, but it should be subjected to control measurements in a cyclical manner. The laser scanning method used allowed for a wide and accurate scope of the study of the geometry of the church structure, without the need to disorganize its equipment.

scholarly journals DEFORMATION MONITORING OF RETROFITTED SHORT CONCRETE COLUMNS WITH LASER SENSOR

2016 ◽  
Vol XLI-B5 ◽  
pp. 765-769
Author(s):  
E. Ö. Avsar ◽  
M. F. Celik ◽  
E. Binbir ◽  
A. E. Arslan ◽  
D. Çokkeçeci ◽  
...  
Keyword(s):  
Laser Scanning ◽  
Reference Sample ◽  
Experimental Studies ◽  
Construction Materials ◽  
Mechanical Tests ◽  
Deformation Monitoring ◽  
Laser Sensor ◽  
Scanning Method ◽  
Compression Load ◽  
Short Columns

This paper presents one of the applications of monitoring mechanical tests carried out in Construction Materials Laboratory of Istanbul Technical University. In Turkey, as in many countries, large amount of existing buildings exposed to seismic hazard, therefore various analytical and experimental studies are being conducted to contribute to the solution of the problem. One of the new generation retrofitting techniques is to strength the structural members by using Fiber Reinforcing Polymer (FRP). This study summarize the results of monitoring of deformations short concrete column samples under the incremental compression load. In this study, result of two rectangular short columns are given. One of them was tested as a reference sample, the other sample were tested after strengthening by PET reinforced polymer composite materials. Besides conventional displacement and strain measurement systems, laser scanning method was used to get three dimensional deformed shape of sample at each selected steps.

A Direct Filling Algorithm of Isogram in Complex Boundary

2013 ◽  
Vol 756-759 ◽  
pp. 3362-3365
Author(s):  
Lin Na Huang ◽  
Guang Zhong Liu
Keyword(s):  
New Method ◽  
Inclusion Relation ◽  
Scanning Method ◽  
Point Calculation ◽  
Complex Boundary ◽  
Area Filling

On basis of summarizing the existing isogram filling algorithm, this paper puts forwards a direct filling algorithm of isogram in complex boundary. Compared with the point-by-point scanning method and algorithm of area filling, this new algorithm has no necessity not only in point-by-point calculation of interpolation, but also in tracing inclusion relation between equivalent areas and determination areas, which makes filling speed faster. It is proved with practice that the new method can fill isopleth map in milliseconds.

Sign in / Sign up

Export Citation Format

Share Document