scholarly journals Biochars derived from bamboo and rice straw for sorption of basic red dyes

PLoS ONE ◽  
2021 ◽  
Vol 16 (7) ◽  
pp. e0254637
Author(s):  
Ebenezer Ampofo Sackey ◽  
Yali Song ◽  
Ya Yu ◽  
Haifeng Zhuang
Keyword(s):  
Adsorption Capacity ◽  
Rice Straw ◽  
Low Cost ◽  
Dye Adsorption ◽  
Freundlich Isotherm ◽  
Second Order ◽  
Isotherm Models ◽  
Acceptor Interaction ◽  
Equilibrium Data ◽  
Pseudo Second Order

The primary purpose of this study is to eliminate Basic Red 46 dye from aqueous solutions utilizing batch experiments by adsorption on biochars prepared from bamboo and rice straw biomass. Biochars prepared from bamboo (B), and rice straw (R) was pyrolyzed at 500°C (B500 and R500). Scanning Electron Microscopy (SEM), Fourier Transform Infrared (FTIR) Spectroscopy, X-ray Diffraction (XRD), and surface area and porosity analyzers were used to characterize the B500 and R500 samples. The characterization results indicated that the biochars possessed an amorphous porous structure with many functional groups consisting primarily of silicates. The adsorption rate of BR46 was evaluated using two kinetic models (pseudo-first-order and pseudo-second-order), and the results indicated that the pseudo-second-order model fitted to the experimental data well (R2>0.99). Nearly 24 h was sufficient to achieve equilibrium with the dye adsorption for the two biochars. R500 had a greater adsorption efficiency than B500. As pH levels increased, the dye’s adsorption capability increased as well. The Langmuir and Freundlich isotherm models were used to investigate the equilibrium behavior of BR46 adsorption, and the equilibrium data fitted well with the Langmuir model (R2>0.99) compared to the Freundlich model (R2>0.89). The maximum adsorption capacities of BR46 are 9.06 mg/g for B500 and 22.12 mg/g for R500, respectively. Additionally, adsorption capacity increased as temperature increased, indicating that adsorption is favored at higher temperatures. The electrostatic interaction is shown to be the dominant mechanism of BR46 adsorption, and BR46 acts as an electron-acceptor, contributing to n-π EDA (Electron Donor-Acceptor) interaction. Thermodynamic parameters for the dye-adsorbent system revealed that the adsorption process is spontaneous and feasible. The values of the adsorption coefficient (Kd) were on the order of 102−103. Kd of R500 was greater than that of B500, indicating that R500 had a greater adsorption capacity. The results showed that R500 could be used as a low-cost alternative adsorbent for removing BR46 from effluents.

scholarly journals Effectiveness of Alkali-Acid Treatment in Enhancement the Adsorption Capacity for Rice Straw: The Removal of Methylene Blue Dye

2013 ◽  
Vol 2013 ◽  
pp. 1-15 ◽  
Author(s):  
Nady A. Fathy ◽  
Ola I. El-Shafey ◽  
Laila B. Khalil
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Rice Straw ◽  
Acid Treatment ◽  
Low Cost ◽  
Second Order ◽  
Isotherm Models ◽  
Blue Dye ◽  
Acid Modification ◽  
Pseudo Second Order

The effectiveness of alkali-acid modification in enhancement the adsorption capacity of rice straw (RS) for removing a basic dye was studied. The obtained adsorbents were characterized by slurry pH, pHPZC, iodine number, methylene blue number, FTIR, and SEM analyses. Adsorption of methylene blue (MB) was described by the Langmuir, Freundlich, Tempkin, and Redlich-Peterson isotherm models. Effects of contact time, initial concentration of MB dye, pH of solution, adsorbent dose, salt concentration of NaCl, and desorbing agents on the removal of MB were reported. Kinetic studies were analyzed using the pseudo-first-order, pseudo-second-order, and the intraparticle diffusion models and were found to follow closely the pseudo-second-order model. Equilibrium data were best represented by the Langmuir and Redlich-Peterson isotherms. The adsorption capacities were varied between 32.6 and 131.5 mg/g for untreated and treated RS samples with NaOH-1M citric acid (ARS-1C), respectively. Adsorption behavior of the ARS-1C sample was experimented in a binary mixture containing methylene blue (basic) and reactive blue 19 (acidic) dyes which showed its ability to remove MB higher than RB19. Overall, the results indicate that the alkali-acid treatment proved to be potential modification for producing effective low-cost adsorbents for the removal of the basic dyes from wastewater.

Removal of Reactive Black 5 from wastewater using natural clinoptilolite modified with apolaccase

Clay Minerals ◽  
2015 ◽  
Vol 50 (1) ◽  
pp. 65-76 ◽  
Author(s):  
Hayrunnisa Nadaroglu ◽  
Ekrem Kalkan ◽  
Neslihan Celebi ◽  
Esen Tasgin
Keyword(s):  
Thermodynamic Parameters ◽  
Contact Time ◽  
Low Cost ◽  
Dye Adsorption ◽  
Freundlich Isotherm ◽  
Second Order ◽  
Isotherm Models ◽  
Reactive Black 5 ◽  
Pseudo Second Order ◽  
Natural Clinoptilolite

AbstractIn this study, a clinoptilolite modified with apolaccase was used to adsorb Reactive Black 5 (RB5) dye from aqueous solution using the batch procedure. The influences of pH, contact time, temperature and absorbent dosage on the adsorption were investigated. The optimum adsorption was obtained at pH = 6, contact time = 60 min, temperature = 25ºC and adsorbent dosages of 1.62 and 1.59 mg/50 mL per gram of clinoptilolite and of apolaccase-modified clinoptilolite (LMC), respectively). The adsorption experimental data fitted both the Langmuir and Freundlich isotherm models well. In addition, pseudo-first-order and pseudo-second-order kinetics were used to study the kinetics of RB5 dye adsorption onto natural clinoptilolite and LMC. Adsorption appears to follow pseudo-second-order kinetics with a high correlation coefficient. Thermodynamic parameters such as changes in the free energy (ΔG°), enthalpy (ΔH°) and entropy (ΔS°) of adsorption were calculated. The thermodynamic parameters indicate that the adsorption of RB5 dye onto LMC was less spontaneous, feasible and endothermic. The LMC can be used as an alternative low-cost adsorbent for the dye removal from aqueous solutions.

Removal of Rhodamine B from Wastewater by Rectorite and Sepiolite-Kinetic Study and Equilibrium Isotherm Analyses

2011 ◽  
Vol 183-185 ◽  
pp. 362-366 ◽  
Author(s):  
Jun Li ◽  
Ming Zhen Hu
Keyword(s):  
Rhodamine B ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Second Order ◽  
Order Kinetic ◽  
Isotherm Equation ◽  
Adsorption Removal ◽  
Equilibrium Data ◽  
Order Kinetic Model ◽  
Pseudo Second Order

Adsorption removal of a cationic dye, rhodamine B (RhB) from water onto rectorite and sepiolite was investigated. The rectorite and sepiolite were characterized by Fourier transform infrared (FT-IR) spectroscopy and scanning electron microscopy (SEM). Attempts were made to fit the isothermal data using Langmuir and Freundlich equations. The experimental results have demonstrated that the equilibrium data are fitted well by a Freundlich isotherm equation. Pseudo-first-order and pseudo-second-order models were considered to evaluate the rate parameters. The experimental data were well described by the pseudo-second-order kinetic model. The results indicate that the rectorite exhibited higher adsorption capacity for the removal of RhB than sepiolite and could be employed as a low-cost alternative in wastewater treatment for the removal of cationic dyes.

scholarly journals Kush - A Potential Biosorbent in the removal of Cd (II) and Zn (II) from aqueous solution

2012 ◽  
Vol 27 ◽  
pp. 107-114
Author(s):  
Jagjit Kour ◽  
P. L. Homagai ◽  
M. R. Pokherel ◽  
K. N. Ghimire
Keyword(s):  
Low Cost ◽  
Freundlich Isotherm ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Waste Streams ◽  
Adsorption Capacities ◽  
Optimum Ph ◽  
Equilibrium Data ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order

The industrial discharge of heavy metals into waters' course is one of the major pollution problems affecting water quality. Therefore, they must be removed prior to their discharge into waste streams. An efficient and low-cost bioadsorbent has been investigated from Desmostachya bipinnata (Kush) by charring with concentrated sulphuric acid and functionalized with dimethylamine.It was characterised by SEM, FTIR and elemental analysis. The effect of pH, initial concentration and contact time of the metal solution was monitered by batch method. The maximum adsorption capacities were determined for Cd and Zn at their optimum pH 6. The equilibrium data were analysed using Langmuir and Freundlich isotherm models. Langmuir isotherm model fitted well and the rate of adsorption followed the pseudo second order kinetic equation.DOI: http://dx.doi.org/10.3126/jncs.v27i1.6669 J. Nepal Chem. Soc., Vol. 27, 2011 107-114  

Kinetic Study and Equilibrium Isotherm Analysis of Cationic Dye Adsorption onto Attapulgite and Rectorite

2012 ◽  
Vol 446-449 ◽  
pp. 2960-2963
Author(s):  
Jing Yan Song ◽  
Jing Yang
Keyword(s):  
Low Cost ◽  
Dye Adsorption ◽  
Second Order ◽  
Order Kinetic ◽  
Cationic Dye ◽  
Equilibrium Data ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Ft Ir ◽  
Langmuir And Freundlich Equations

The adsorption properties of the attapulgite and the rectorite were investigated by removal of a cationic dye, methylene blue (MB) from aqueous solution. The attapulgite and the rectorite were characterized by Fourier transform infrared (FT-IR) spectroscopy, Brunauer-Emmett-Teller (BET) and scanning electron microscopy (SEM). The analysis of the isotherm equilibrium data using the Langmuir and Freundlich equations showed that the data fitted better with Langmuir model. Pseudo-first-order and pseudo-second-order models were considered to evaluate the rate parameters. The experimental data were well described by the pseudo-second-order kinetic model. The results indicate that the attapulgite exhibited higher adsorption capacity for MB than rectorite and could be employed as a low-cost alternative in wastewater treatment for the removal of cationic dyes.

scholarly journals Comparative Study of Ni-Zn LHS and Mg-Al LDH Adsorbents of Navy Blue and Yellow F3G Dye

2018 ◽  
Vol 16 (1) ◽  
pp. 36 ◽  
Author(s):  
Idha Yulia Ikhsani ◽  
Sri Juari Santosa ◽  
Bambang Rusdiarso
Keyword(s):  
Adsorption Capacity ◽  
Freundlich Isotherm ◽  
Second Order ◽  
Isotherm Models ◽  
Disperse Dyes ◽  
Order Kinetic ◽  
Initial Ph ◽  
Isotherm Adsorption ◽  
Order Kinetic Model ◽  
Pseudo Second Order

Adsorption of disperse dyes from wastewater onto Ni-Zn LHS (layered hydroxide salts) and Mg-Al LDH (layered double hydroxides) has been compared in this study. Effects of initial pH solution, contact time and initial dye concentration were investigated. The ability of the adsorbent to be reused was also studied. The results showed that acidic condition was favorable for the adsorption of each dyes onto both adsorbent. The adsorption kinetics was studied using pseudo-first-order, pseudo-second-order and Santosa’s kinetics models. The experimental data fits well with the pseudo-second order kinetic model. The equilibrium adsorption data were analyzed using Langmuir and Freundlich isotherm models. The results showed that adsorption of navy blue onto both adsorbent followed Freundlich isotherm adsorption, while yellow F3G followed Langmuir isotherm adsorption. In the application for the adsorption the wastewater containing dyes, Ni-Zn LHS has a better adsorption capacity of 52.33 mg/g than that of Mg-Al LDH that 30.54 mg/g. Calcination of the adsorbent which has already been used increased the adsorption capacity of Mg-Al LDH to 84.75 mg/g, but decreased the adsorption capacity of the Ni-Zn LHS to 42.65 mg/g.

scholarly journals Adsorptive removal of pentachlorophenol from aqueous solutions using powdered eggshell

2017 ◽  
Vol 43 (3) ◽  
pp. 10-16 ◽  
Author(s):  
Krzysztof Kuśmierek ◽  
Paulina Idźkiewicz ◽  
Andrzej Świątkowski ◽  
Lidia Dąbek
Keyword(s):  
Aqueous Solutions ◽  
Low Cost ◽  
Second Order ◽  
Isotherm Models ◽  
Order Model ◽  
Diffusion Kinetic ◽  
Monolayer Adsorption ◽  
Equilibrium Data ◽  
Intra Particle Diffusion ◽  
Pseudo Second Order

AbstractThe usefulness of untreated powdered eggshell as low-cost adsorbent for the removal of pentachlorophenol (PCP) from aqueous solutions was investigated. The most important parameters affecting the adsorption process, including the pH and ionic strength, were examined. The adsorption characteristics of PCP onto eggshell were evaluated in terms of kinetic and equilibrium parameters. The kinetic data were studied in terms of the pseudo-first order, pseudo-second order and intra-particle diffusion kinetic models. The equilibrium data were analyzed using the Langmuir, Freundlich, Sips and Redlich-Peterson isotherm models. The pseudo-second order model best described the adsorption kinetics. Using the Langmuir equation, the monolayer adsorption capacity of eggshell for PCP was found to be 0.127 mg/g. The results showed that PCP can be effectively removed from aqueous solution employing eggshell as a cheap adsorbent.

scholarly journals Equilibrium and kinetic studies of acid dye adsorption on palm oil empty fruit bunch

2014 ◽  
Vol 9 (3) ◽  
Author(s):  
Norini Tahir ◽  
Zaiton Abdul Majid
Keyword(s):  
Palm Oil ◽  
Low Cost ◽  
Agricultural Waste ◽  
Dye Adsorption ◽  
Freundlich Isotherm ◽  
Second Order ◽  
Order Kinetic ◽  
Empty Fruit Bunch ◽  
Batch Mode ◽  
Pseudo Second Order

Palm oil empty fruit bunch (POEFB), an agricultural waste, used as low-cost adsorbent for removal Acid Orange 51 (AO51) dye from aqueous solutions was studied. Batch mode experiments were carried out at room temperature (28 ± 2) °C to study the effects of contact time and initial dye concentrations (10-200 mg/L). The equilibrium adsorption data of AO51 dye on empty fruit bunch were analyzed by three isotherms, namely the Langmuir isotherm, Freundlich isotherm and Temkin isotherm model. The result indicated that the equilibrium sorption fitted well with the Freundlich isotherm, displaying higher regression coefficient, R2value. The monolayer adsorption capacity of POEFB was found to be 166.67 mg/g. The kinetic data obtained at different concentrations have been analyzed using the pseudo-first-order, pseudo-second-order and intraparticle diffusion models. It was shown that pseudo-second-order kinetic model could best describe the adsorption kinetics.

Adsorption of geosmin and 2-methylisoborneol onto granular activated carbon in water: isotherms, thermodynamics, kinetics, and influencing factors

2019 ◽  
Vol 80 (4) ◽  
pp. 644-653
Author(s):  
Lingfei Ma ◽  
Fangyuan Peng ◽  
Haipu Li ◽  
Chaoyi Wang ◽  
Zhaoguang Yang
Keyword(s):  
Particle Size ◽  
Activated Carbon ◽  
Adsorption Capacity ◽  
Granular Activated Carbon ◽  
Freundlich Isotherm ◽  
Second Order ◽  
Isotherm Models ◽  
Pseudo Second Order ◽  
Adsorption Entropy ◽  
Natural Organic Material

Abstract Adsorption was found to be an acceptable treatment option to remove geosmin (GSM) and 2-methylisoborneol (2-MIB). It is meaningful to investigate the adsorption capacity of granular activated carbon (GAC) for the two algal odorants in water, and the influences of natural organic material (NOM) and particle size. The adsorption process was studied with the four isotherm models (Langmuir, Freundlich, Temkin, and modified Freundlich), four kinetic models (pseudo first-order, pseudo second-order, Elovich, and intra-particle), and thermodynamics. The results showed that the adsorption of both compounds could be best described by the modified Freundlich isotherm and pseudo second-order model, and the obtained thermodynamic parameters (changes in heat of adsorption, entropy, and Gibbs free energy) revealed that the adsorption was endothermic and spontaneous. Downsizing the particle size of GAC was effective for improving the adsorption capacity and rate. The concentrations of the two odorants could be reduced from 500 ng L−1 to less than 10 ng L−1 with the presence of NOM (<20 mg L−1 total organic carbon, TOC).

scholarly journals Batch Adsorption of Maxilon Red GRL from Aqueous Solution by Natural Sugarcane Stalks Powder

2013 ◽  
Vol 2013 ◽  
pp. 1-8 ◽  
Author(s):  
Gamal Owes El-Sayed ◽  
Talaat Younis Mohammed ◽  
Ashraf Abd-Allah Salama
Keyword(s):  
Aqueous Solution ◽  
Dye Removal ◽  
Dye Adsorption ◽  
Freundlich Isotherm ◽  
Isotherm Models ◽  
Batch Adsorption ◽  
Textile Dye ◽  
Initial Ph ◽  
Equilibrium Data ◽  
Pseudo Second Order

Sugarcane stalks powder was tested for its efficiency of removing a textile dye Maxilon Red GRL from aqueous solution. Different parameters affecting dye removal efficiency were studied. These parameters include contact time, initial dye concentration, adsorbent dose, ionic strength, pH, and temperature. Langmuir and Freundlich isotherm models were applied to the equilibrium data. The data fitted well with the Langmuir isotherm (). The maximum monolayer adsorption capacity () was found to be 20.96 mg/g at an initial pH of 7.2. The temperature variation study showed that dye adsorption is exothermic and spontaneous with increased randomness at the solid solution interface. The results indicated that sugarcane stalks could be an alternative for more costly adsorbents used for dye removal. The kinetic of the adsorption process followed the pseudo second-order kinetics model.

Sign in / Sign up

Export Citation Format

Share Document