scholarly journals INFLUENCE OF CHEMICAL POLYMER ADDITIVE ON THE PHYSICAL AND MECHANICAL PROPERTIES OF EXPANDED POLYSTYRENE CONCRETE

2020 ◽  
Vol 60 (2) ◽  
pp. 158-168
Author(s):  
John Wasiu ◽  
Daoud Mohammad Baba
Keyword(s):  
Flexural Strength ◽  
Water Absorption ◽  
Expanded Polystyrene ◽  
Engineering Properties ◽  
Partial Replacement ◽  
Light Weight ◽  
Polymer Additive ◽  
Liquid Form ◽  
Split Tensile Strength ◽  
Conventional Concrete

This research investigated the effect of Renolith chemical polymer additive (RCPA) on the properties of expanded polystyrene (ESP) concrete. Renolith chemical additive is a polymer-based product in a liquid form made up of latex and cellulose. Polystyrene panels were collected as a waste materials and grinded into smaller beads. An experimental investigation was carried out on the EPS replacement ranging from 0% to 100% on the M30 (C25/C30) mix design. Engineering properties, such as workability, density, water absorption, compressive strength, split tensile strength, and flexural strength tests, were studied for both the conventional and EPS concrete. The results indicate that workability increases with increasing amount of EPS contents. Water absorption, compressive, tensile, and flexural strength yielded a satisfactory result at 0-50% replacement. The density of the EPS concrete at 0-37.5% replacement revealed similar values to a conventional concrete; and light-weight concrete (1817.5 - 1030 kg⁄m3) was achieved at a 50-100% replacement. Generally, the addition of the RCPA to the concrete mix has caused an improvement in the properties of the EPS concrete. It was concluded that EPS beads can be used as a partial replacement for coarse aggregates in the production of both structural light-weight and dense concrete. The replacement of coarse aggregate with EPS beads showed a positive application as an alternative material for the construction industry.

scholarly journals Combined Effects of Bottom Ash and Expanded Polystyrene on Light-weight Concrete Properties

2018 ◽  
Vol 251 ◽  
pp. 01007 ◽  
Author(s):  
Lam Tang Van ◽  
Tho Vu Dinh ◽  
Dien Vu Kim ◽  
Boris Bulgakov ◽  
Olga Aleksandrova ◽  
...  
Keyword(s):  
High Performance Concrete ◽  
Bottom Ash ◽  
Expanded Polystyrene ◽  
Engineering Properties ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Light Weight ◽  
Combined Effects ◽  
Cement Ratio ◽  
Light Weight Concrete

The benefits of using waste materials as a partial replacement for cement in high performance concrete are also discussed. This paper presents the combined effects of bottom ash TPP “Vung Ang” and expanded polystyrene aggregate on different the properties of light-weight concrete. Twenty different concrete mixtures with a water to cement ratio of 0.4 and superplasticizer to cement ratio of 0.015 were used. On the one hand, the EPS was partially replaced with (0 ÷ 40)% by volume of concrete mixture. On the other hand, the fine aggregate was replaced with (0 ÷ 30)% by mass of BA TPP “Vung Ang”. The engineering properties, including workability, density and compressive strength of light-weight concrete were investigated at different curing times. The level of decrease in the strength depends upon the replacement level of EPS and BA. Specifically, the concrete containing 40% EPS and 30% BA at 28 days of age decrease in average density and strength were 43.2% and 26.4%, respectively, in comparison with the control concrete.

scholarly journals Structural Use of Expanded Polystyrene Concrete

2020 ◽  
Vol 5 (6) ◽  
pp. 1131-1138
Author(s):  
Adeniran Jolaade ADEALA ◽  
Olugbenga Babajide SOYEM
Keyword(s):  
Environmental Pollution ◽  
Lightweight Concrete ◽  
Physical And Mechanical Properties ◽  
Consumer Products ◽  
Expanded Polystyrene ◽  
Engineering Properties ◽  
Partial Replacement ◽  
Construction Companies ◽  
Fine Aggregates ◽  
Concrete Matrix

Expanded polystyrene (EPS) wastes are generated from industries and post-consumer products. They are non-biodegradable but are usually disposed by burning or landfilling leading to environmental pollution. The possibility of using EPS as partial replacement for fine aggregates in concrete has generated research interests in recent times. However, since the physical and mechanical properties of EPS are not like those of conventional fine aggregates, this study is focussed on the use of EPS as an additive in concrete while keeping other composition (sand and granite) constant. Expanded polystyrene was milled, the bulk density of EPS was 10.57kg/m3 and particle size distributions were determined. Engineering properties of expanded polystyrene concrete were determined in accordance with BS 8110-2:1985. The result showed that the amount of expanded polystyrene incorporated in concrete influence the properties of hardened and fresh concrete. The compressive strengths of 17.07MPa with 5 % expanded polystyrene concrete at 28 days for example can be used as a lightweight concrete for partitioning in offices. Incorporating expanded polystyrene granules in a concrete matrix can produce lightweight polystyrene aggregate concrete of various densities, compressive strengths, flexural strengths and tensile strengths. In conclusion, this reduces environmental pollution, reduction in valuable landfill space and also for sustainability in construction companies

scholarly journals Optimizing the Tensile Strength of Polystyrene Lightweight Concrete: A Panacea for Sustainable Housing Development in Developing Countries

2021 ◽  
pp. 107-125
Author(s):  
S. E. Ubi
Keyword(s):  
Tensile Strength ◽  
Large Scale ◽  
Building Blocks ◽  
Expanded Polystyrene ◽  
Partial Replacement ◽  
Split Tensile Strength ◽  
Polystyrene Beads ◽  
Coarse Aggregates ◽  
Lattice Design ◽  
Strength Result

The use of polystyrene beads in concrete applications has been limited due to its perceived low strength properties. Tensile strength test is an important test that determines the vulnerability of concrete to tensile cracking due to the weight of the structural load. Water, sand, coarse aggregates, expanded polystyrene beads, and ordinary Portland cement are the materials used for this study. All the materials were batched according to their weight, except for polystyrene and coarse aggregates which were batched in volume after mixing them together. The polystyrene partial replacement level was considered at 12% of the coarse aggregate volume. The model equation adopted for this study was based on Scheffe’s {4, 2} simplex lattice design for both Pseudo component and component proportional models. The actual model was developed from the 28th day test result. The Mathlab and Minitab 16 software were used in this study to generate the actual mix ratios. The results obtained showed that both Pseudo component and component proportional models both produced an average split tensile strength of about 5.10N/mm2. This implied that the results of this study produced a split tensile strength result that varied between 18% - 19% of its compressive strength result. This showed that the materials and the mix ratios optimized in this study are suitable as building blocks for residential low rising buildings and as partition slaps for high rising buildings. The lightweight property makes it highly suitable for large scale application in high rising structures as internal partition slaps only.

scholarly journals Suitability of Scoria as Fine Aggregate and Its Effect on the Properties of Concrete

2019 ◽  
Vol 11 (17) ◽  
pp. 4647 ◽  
Author(s):  
Warati ◽  
Darwish ◽  
Feyessa ◽  
Ghebrab
Keyword(s):  
Construction Materials ◽  
Energy Utilization ◽  
Engineering Properties ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Test Results ◽  
River Sand ◽  
Conventional Concrete ◽  
Efficient Energy ◽  
Concrete Production

The increase in the demand for concrete production for the development of infrastructures in developing countries like Ethiopia leads to the depletion of virgin aggregates and high cement demand, which imposes negative environmental impacts. In sustainable development, there is a need for construction materials to focus on the economy, efficient energy utilization, and environmental protections. One of the strategies in green concrete production is the use of locally available construction materials. Scoria is widely available around the central towns of Ethiopia, especially around the rift valley regions where huge construction activities are taking place. The aim of this paper is therefore to analyze the suitability of scoria as a fine aggregate for concrete production and its effect on the properties of concrete. A differing ratio of scoria was considered as a partial replacement of fine aggregate with river sand after analyzing its engineering properties, and its effect on the mechanical properties of concrete were examined. The test results on the engineering properties of scoria revealed that the material is suitable to be used as a fine aggregate in concrete production. The replacement of scoria with river sand also enhanced the mechanical strength of the concrete. Generally, the findings of the experimental study showed that scoria could replace river sand by up to 50% for conventional concrete production.

scholarly journals Performance of Concrete with Waste Plastics and M-Sand as Replacement for Fine Aggregate

2020 ◽  
Vol 9 (2) ◽  
pp. 1667-1669
Keyword(s):  
Cost Effective ◽  
Raw Material ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
River Sand ◽  
Split Tensile Strength ◽  
Conventional Concrete ◽  
Waste Plastic ◽  
Fine Aggregates ◽  
Territorial Government

In recent days, there is an intense need for an alternate cost effective and sustainable raw material for concrete which does not make the structure inferior in strength. An experimental study on the utilization of the waste plastic and M-sand in the place of river sand and aggregate partially was performed in paper. In the scenario of scarcity of river sand due to the territorial government action and restriction of usage because of the eco and environmental consideration, M-Sand is found to be an effective replacement and cost effective material. Concrete specimens were casted with combination of M-sand and plastic waste with 5%, 10%, 15%, 20% and 25% and compared against control mix. Cube test for compressive strength study, cylinder test for split tensile strength study and prism test for flexural strength study were done with the proposed concert mixture. All the specimens and tests were done for different curing period of 7, 14 and 28 days. The results obtained from the proposed mix of concrete are compared with the conventional concrete mix specimen respectively. The replacement of fine aggregates reduces the quantity of river sand to be used in concrete and also plastic fibres are proved to be more economical. Positive performance of the concrete with waste plastic and M-Sand as partial replacement of river sand was observed on all the experiments and found optimal in sustainable and economical performance.

scholarly journals Study of Light Weight Fibre Reinforced Concrete by Partial Replacement of Coarse Aggregate with Pumice Stone

2021 ◽  
Vol 9 (9) ◽  
pp. 933-940
Author(s):  
Mohammed Sohel Ahmed
Keyword(s):  
Compressive Strength ◽  
Coarse Aggregate ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Light Weight ◽  
Structural Members ◽  
Conventional Concrete ◽  
Shrinkage Cracking ◽  
Pumice Stone ◽  
Average Compressive Strength

Abstract: As the demand for the structural members application in the concrete industry is continuously increasing simultaneously many a times it is required to lower the density of concrete enabling light weight which helps in easy handling of the concrete and its members. In this research an experimental endeavour has been made to equate conventional concrete with light weight by partially substituting the coarse aggregate with the pumice stone aggregate in M30 grade mix design. Simultaneously small fibres of Recron3's Polypropylene have been applied to the concrete as a reinforcing medium to minimize shrinkage cracking and improve tensile properties. The coarse aggregate was substituted by the pumice aggregate in 10, 20, 30, 40, and 50 percent and fibres respectively in 0.5, 1, 1.5, 2 and 2.5 percent. The experiment is focused on strength parameters to determine the most favourable optimum percent with respect to conventional concrete. Keywords: OPC (Ordinary Portland Cement)1, FA (Fine Aggregate)2, CA (Coarse Aggregate) 3, fck (Characteristic Compressive Strength at 28days)4, Sp. Gr (Specific Gravity)5, WC (Water Content)6, W/C (Water Cement Ratio)7, S (Standard Deviation)8, Fck (Target Average Compressive Strength at 28days)9.

scholarly journals Investigative Study of Partial Replacement of Cement with Bio-Cement, Fly Ash and Natural Pozzolans

2021 ◽  
Vol 12 (1S) ◽  
pp. 432-436
Author(s):  
Dr.Sarvesh, Et. al.
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Main Property ◽  
Partial Replacement ◽  
Self Healing ◽  
Split Tensile Strength ◽  
Conventional Concrete ◽  
Quality Properties ◽  
Natural Pozzolans ◽  
The Impact

Concrete is usually a combination of cement, coarse particles (aggregates and Sand) and water. It is used to design and improve the infrastructures.It is used to design and improve the infrastructures. Concrete has many advantages and disadvantage. The main property that is characteristic to a concrete’s workability is its compressive strength. Only through this single test, one can judge if cementing has been done appropriately. Possible advancements for development include the use of non-traditional and creative materials, and the reuse of waste materials with a specific end goal to replenish the absence of specific assets and to discover alternative ways to monitor the Earth..This investigation concentrate on Compressive strength, flexural and split tensile strength of Conventional Concrete (CC) and Class C fly ash remains with bio-cement and natural pozzolans to consider the impact of bio-concrete with blend extents of 0%,0.25%,0.5%,1% and 1.5% on quality properties. Moreover, effective self-healing usually occurred due to the use of polymers, microorganism and additional cementing material. It is the key issue to find out the self-healing efficiency’s effect to sealing the crack width successfully. And good resistance was observed during the bacterial chemical process against the freeze and thaw attacks.

scholarly journals Engineering Properties of Concrete by Partial Replacement of Cement with Aluminium Slag and Fine Aggregate with Foundary Sand

2019 ◽  
Vol 8 (6) ◽  
pp. 3870-3874
Keyword(s):  
Waste Product ◽  
Engineering Properties ◽  
Partial Replacement ◽  
Plastic State ◽  
Fine Aggregate ◽  
Structural Elements ◽  
Construction Time ◽  
Conventional Concrete ◽  
Waste Products ◽  
The Matrix

A self-compacting concrete (s.c.c) is a special concrete which settles itself without any vibration due to its own mass and self-weight. This will happen due to use of special admixtures which have tendency to increase the flow of concrete by reducing the viscosity nature. This particular type of concrete was developed by the japan researchers in 1988. Later it was modifies and developed in many parameter’s by UK and U.S.A researchers. This particular thesis is about the improvement of performance of the S.C.C by replacing the fines and cement of the aggregates by the waste products that obtained from the different industries. The fines are replaced partially by crushed sand obtained as quarry waste and the aluminium slag that obtained from many industries as a waste product is partially introduced as binding material By using this S.C.C the problems that are facing by the construction industries during the placement of the concrete will solve. Now days the structures are designed and made as heavy reinforced structures where the sizes of structural elements are restricted due to architectural and some structural considerations. So the concrete that poured in those elements shows the voids and honey combing it can be prevented by using this S.C.C. not only the improvement of the strength but also the construction time and cost also gets reduced by using this product, because with this material no need of vibration. It reduces the time of construction and cost regarding vibration equipment and labor. But the main problem while preparing s.c.c is to select the proper admixture to prevent the cracking and shrinkage issues. This type of concrete requires 20-25 percent higher matric paste when compared to conventional concrete. This thesis works on mainly preparing the most feasible mix for s.c.c with the partial replacement of fines and cement by above mentioned materials which makes the matrix still in plastic state without altering the original properties of the concrete. The second task is to prepare the specimens for different strength tests and like compression and tensile and bending parameters check along with the considering the shrinkage issues.

scholarly journals Experimental Study on Engineering Properties of Cement Concrete Reinforced with Nylon and Jute Fibers

Buildings ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 454
Author(s):  
Naraindas Bheel ◽  
T. Tafsirojjaman ◽  
Yue Liu ◽  
Paul Awoyera ◽  
Aneel Kumar ◽  
...  
Keyword(s):  
Flexural Strength ◽  
Water Absorption ◽  
Natural Fiber ◽  
Drying Shrinkage ◽  
Engineering Properties ◽  
Synthetic Fiber ◽  
Jute Fiber ◽  
Cement Concrete ◽  
Jute Fibers ◽  
Concrete Production

The use of synthetic fiber and natural fiber for concrete production has been continuously investigated. Most of the materials have become popular for their higher flexibility, durability, and strength. However, the current study explores the engineering properties of cement concrete reinforced with nylon and jute fibers together. Varying proportions and lengths of nylon and jute fibers were utilized in the concrete mixture. Hence, the combined effects of nylon and jute fibers on workability, density, water absorption, compressive, tensile, flexural strength, and drying shrinkage of concrete were investigated. Results showed that concrete with 1% of nylon and jute fibers together by the volume fraction showed a maximum enhancement of the compressive strength, split tensile strength, and flexural strength by 11.71%, 14.10%, and 11.04%, respectively, compared to the control mix of concrete at 90 days. However, the water absorption of concrete increased with increasing nylon and jute fiber contents. The drying shrinkage of concrete decreased with the addition of nylon and jute fibers together after 90 days. Thus, the sparing application of both nylon and jute fiber as discussed in this study can be adopted for concrete production.

scholarly journals A Study on Mechanical Properties of Conventional Concrete and Coconut Shell Concrete by Replacing Cement with Silica Fume

2018 ◽  
Vol 7 (2.12) ◽  
pp. 437
Author(s):  
V R.Prasath Kumar ◽  
K Gunasekaran ◽  
Sreerag K P
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Silica Fume ◽  
Building Materials ◽  
Coarse Aggregate ◽  
Coconut Shell ◽  
Split Tensile Strength ◽  
Conventional Concrete ◽  
Coconut Shells

High standing estimation of building materials utilized for development is a component of incredible concern. Coconut shell as a completely substitution in the place of coarse aggregate may totally effective for designers in construction industry. The coconut shell concrete is a light weight solid which may decrease the self-heap of a structure. The under taken project depends on inspecting attributes of coconut shell concrete when contrasted with conventional concrete. Coconut shells going from 10mm strainer and held on 6.3mm were considered to utilize for this study. For the current study M100 grade concrete is used to cast the specimens. The principle properties considered testing on coconut shell concrete and conventional concrete is compressive strength, split tensile strength and flexural strength. Examples were taken by supplanting coarse aggregate with coconut shells completely and cement is supplanted by silica fume with various extents of 5%, 10%, 15%, 20%, 25% for compressive strength test and tests were done at 3, 7, 28, 56 and 90 days of curing, it is observed that the ideal compressive strength outcomes were obtained at 10% of silica fume. The flexural strength and  split tensile strength of the specimens are calculated with replacement of cement by silica fume with  different extents of 0%, 5%, 10% and 15%, tests were done at 3, 7 and 28 days of curing. The optimum replacement percentage of cement by silica fume is 10% for compressive strength, split tensile and flexural strength. The primary principle is to lessen the utilization of natural aggregate by supplanting them with coconut shells and to decrease the density of concrete which makes concrete for simple dealing.  

Sign in / Sign up

Export Citation Format

Share Document