PROCESSES AND DEVICES FOR PRESSING OF GRAPHITOPLAST BLANKS FOR ELECTRIC BRUSHES REINFORCED AND NOT REINFORCED WITH CURRENT-CONDUCTING WIRES

2020 ◽  
pp. 21-26
Author(s):  
M. N. Samodurova ◽  
L. A. Barkov ◽  
Yu. S. Latfulina
Keyword(s):  
Mechanical Properties ◽  
Physical And Mechanical Properties ◽  
Electric Machines ◽  
Labor Intensity ◽  
High Demand ◽  
Contact Wire ◽  
High Labor ◽  
Long Duration ◽  
Current Leads ◽  
Inefficient Operation

The article is devoted to processes and equipment for the production of non-reinforced brushes and reinforced with a contact wire. The shortcomings of the block molding technology of brushes are shown: high labor intensity of the process, low productivity, long duration of operations in the manufacture of brushes, high demand for various devices and equipment for machining, including diamond equipment, and a laborious and inefficient operation for providing brushes with current leads. Finished products receive insufficient density and reduced physical and mechanical properties. As a solution to these problems, the improved patented methods for the manufacture of brushes for electric machines, the device for their pressing, developed by the scientists of SUSU are given, and the phenomena that occur in the implementation of these methods are described.

MECHANICAL AND THERMAL PROPERTIES OF SAWDUST CONCRETE

2017 ◽  
Vol 79 (6) ◽  
Author(s):  
Ruhal Pervez Memon ◽  
Abdul Rahman Mohd. Sam ◽  
A. S. M. Abdul Awal ◽  
Lemar Achekzai
Keyword(s):  
Heat Transfer ◽  
Mechanical Properties ◽  
Tensile Strength ◽  
Thermal Properties ◽  
Lightweight Concrete ◽  
Physical And Mechanical Properties ◽  
Developing Nations ◽  
Mechanical And Thermal Properties ◽  
Construction Technology ◽  
Long Duration

 Industrialization in developing countries has resulted in an increase in agricultural output and consequent accumulation of unmanageable agro wastes. Pollution arising from such wastes is a matter of concern for many developing nations. The aim of this study is to investigate the behavior of lightweight concrete and the utilization of sawdust as waste material in concrete. This paper focuses on the manufacturing of concrete which possess long duration heat transfer by using sawdust waste. In this research, cement to sawdust ratio of 1:1, 1:2 and 1:3 by volume was prepared for sawdust concrete, and the ratio of sand was kept constant that is 1. At these ratios, the mechanical and thermal properties like density, workability, strength and heat transfer were measured after, 7, 28 and 56 days of air curing. The tests results show that with the increase in the amount of sawdust, the workability, compressive strength, tensile strength and flexural strength decreased. It also resulted in reduction of heat transfer of sawdust concrete. Taking into account the overall physical and mechanical properties, sawdust concrete can be used in construction technology. 

PEMANFAATAN KAYU AKASIA MANGIUM (Acacia mangium Willd) UNTUK MEBEL

2012 ◽  
Vol 4 (1) ◽  
pp. 1
Author(s):  
Djoko Purwanto
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Physical Properties ◽  
Treatment Process ◽  
Acacia Mangium ◽  
Physical And Mechanical Properties ◽  
Wood Fibers ◽  
Test Parameters ◽  
Mechanical And Physical Properties ◽  
Scale Scores

Timber Acacia mangium (Acacia mangium, Willd) for Furniture. The study aims to determine the mechanical and physical properties and the decorative value (color and fiber) wood of acacia mangium with using finishing materials. This type of finishing material used is ultran lasur natural dof ,ultran lasur classic teak, aqua politur clear dof, aqua politur akasia dan aqua politur cherry. After finishing the wood is stored for 3 months. Test parameters were observed, namely, physical and mechanical properties of wood, adhesion of finishing materials, color and appearance of the fiber, and timber dimensions expansion. The results showed that the mechanical physical properties of acacia wood qualified SNI. 01-0608-89 about the physical and mechanical properties of wood for furniture, air dry the moisture content from 13.78 to 14.89%, flexural strength from 509.25 to 680.50 kg/cm2, and compressive strength parallel to fiber 342.1 - 412.9 kg/cm2. Finishing the treatment process using five types of finishing materials can increase the decorative value (color and fiber) wood. Before finishing the process of acacia mangium wood has the appearance of colors and fibers and less attractive (scale scores 2-3), after finishing acacia wood fibers have the appearance of colors and interesting and very interesting (scale 4-5).Keywords: mangium wood, mechanical properties, decorative value, finishing, furniture.

Physical and Mechanical Properties of Tenun Pahang Fabrics using Alternative Yarns

2016 ◽  
Vol 13 (2) ◽  
pp. 67
Author(s):  
Engku Liyana Zafirah Engku Mohd Suhaimi ◽  
Jamil Salleh ◽  
Suzaini Abd Ghani ◽  
Mohamad Faizul Yahya ◽  
Mohd Rozi Ahmad
Keyword(s):  
Mechanical Properties ◽  
Physical And Mechanical Properties ◽  
The Other ◽  
Silk Fabrics ◽  
Recovery Angle ◽  
Made In

An investigation on the properties of Tenun Pahang fabric performances using alternative yarns was conducted. The studies were made in order to evaluate whether the Tenun Pahang fabric could be produced economically and at the same time maintain the fabric quality. Traditional Tenun Pahang fabric uses silk for both warp and weft. For this project, two alternative yarns were used which were bamboo and modal, which were a little lower in cost compared to silk. These yarns were woven with two variations, one with the yarns as weft only while maintaining the silk warp and the other with both warp and weft using the alternative yarns. Four (4) physical testings and three (3) mechanical testings conducted on the fabric samples. The fabric samples were evaluated including weight, thickness, thread density, crease recovery angle, stiffness and drapability. The results show that modal/silk and bamboo silk fabrics are comparable in terms of stiffness and drapability, hence they have the potential to replace 100% silk Tenun Pahang.

Basic set of experiments for determination of mechanical properties of sand

2014 ◽  
Vol 62 (1) ◽  
pp. 129-137
Author(s):  
A. Sawicki ◽  
J. Mierczyński
Keyword(s):  
Mechanical Properties ◽  
Soil Mechanics ◽  
Physical And Mechanical Properties ◽  
Local Strain ◽  
Initial State ◽  
Laboratory Equipment ◽  
Additional Information ◽  
Basic Set ◽  
Initial Anisotropy

Abstract A basic set of experiments for the determination of mechanical properties of sands is described. This includes the determination of basic physical and mechanical properties, as conventionally applied in soil mechanics, as well as some additional experiments, which provide further information on mechanical properties of granular soils. These additional experiments allow for determination of steady state and instability lines, stress-strain relations for isotropic loading and pure shearing, and simple cyclic shearing tests. Unconventional oedometric experiments are also presented. Necessary laboratory equipment is described, which includes a triaxial apparatus equipped with local strain gauges, an oedometer capable of measuring lateral stresses and a simple cyclic shearing apparatus. The above experiments provide additional information on soil’s properties, which is useful in studying the following phenomena: pre-failure deformations of sand including cyclic loading compaction, pore-pressure generation and liquefaction, both static and caused by cyclic loadings, the effect of sand initial anisotropy and various instabilities. An important feature of the experiments described is that they make it possible to determine the initial state of sand, defined as either contractive or dilative. Experimental results for the “Gdynia” model sand are shown.

PREPARATION AND CHARACTERIZATION OF REPROCESSED COMPOSITES OF POLYPROPYLENE REINFORCED BY WOOD FIBERS: PHYSICAL AND MECHANICAL PROPERTIES

2017 ◽  
Author(s):  
Thais Helena Sydenstricker Flores-Sahagun ◽  
Kelly Priscila Agapito ◽  
ROSA MARIA JIMENEZ AMEZCUA ◽  
Felipe Jedyn
Keyword(s):  
Mechanical Properties ◽  
Physical And Mechanical Properties ◽  
Wood Fibers

Structure and properties of compact articles from high-alloyed iron powder with adding of boron nitride

2020 ◽  
pp. 39-48
Author(s):  
B. O. Bolshakov ◽  
◽  
R. F. Galiakbarov ◽  
A. M. Smyslov ◽  
◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Boron Nitride ◽  
Grain Boundary ◽  
Bending Strength ◽  
Physical And Mechanical Properties ◽  
Operating Conditions ◽  
Structure And Properties ◽  
Steam Turbines ◽  
Friction Forces ◽  
Wide Range

The results of the research of structure and properties of a composite compact from 13 Cr – 2 Мо and BN powders depending on the concentration of boron nitride are provided. It is shown that adding boron nitride in an amount of more than 2% by weight of the charge mixture leads to the formation of extended grain boundary porosity and finely dispersed BN layers in the structure, which provides a high level of wearing properties of the material. The effect of boron nitride concentration on physical and mechanical properties is determined. It was found that the introduction of a small amount of BN (up to 2 % by weight) into the compacts leads to an increase in plasticity, bending strength, and toughness by reducing the friction forces between the metal powder particles during pressing and a more complete grain boundary diffusion process during sintering. The formation of a regulated structure-phase composition of powder compacts of 13 Cr – 2 Mо – BN when the content of boron nitride changes in them allows us to provide the specified physical and mechanical properties in a wide range. The obtained results of studies of the physical and mechanical characteristics of the developed material allow us to reasonably choose the necessary composition of the powder compact for sealing structures of the flow part of steam turbines, depending on their operating conditions.

Sign in / Sign up

Export Citation Format

Share Document