scholarly journals Potential of Wind Energy in Albania and Kosovo: Equity Payback and GHG Reduction of Wind Turbine Installation

2015 ◽  
Vol 4 (1) ◽  
pp. 11-19
Author(s):  
Mevlan Qafleshi ◽  
Driton R. Kryeziu ◽  
Lulezime Aliko
Keyword(s):  
Wind Energy ◽  
Wind Turbine ◽  
Power Plants ◽  
Combustion Process ◽  
Energy Generation ◽  
Base Case ◽  
Climate Data ◽  
Diesel Generator ◽  
Ghg Reduction ◽  
The Impact

The energy generation in Albania is completely from the hydropower plants. In terms of GHG emissions this is 100% green. In Kosovo 97% of energy is generated from lignite fired power plants. Apart the energy generation, the combustion process emits around 8000 ktCO2/yr and 1.5 Mt of ash in the form of fly and bottom ash. In both countries there is no MWh power generated from wind energy, i.e. this energy source is not utilized. Here, a proposed project for five locations in Albania and Kosovo has been analyzed in detail with the aim of installing a 1kW wind turbine off-grid. The method of study is based on the application of RETScreen International program software. This proposed model is intended to replace a base case- a diesel generator with installed capacity 7kW.  The locations are selected three in Albania: Vlora, Korça and Elbasan, and two in Kosovo: Prishtina and Prizren. All are in different altitudes. By the calculation of RETScreen program, it has been analyzed the feasibility of the proposed projects by installing a wind turbine at hub’s height 20m. The climate data for each location were retrieved by the RETScreen program from NASA. Generally, the calculation of financial parameters for the investments came out to be positive, the impact of GHG reduction very significant. A 5500 USD investment for the implementation of proposed case showed an equity payback time of 2-3 yrs and GHG reduction of 2.2 tCO2/yr. The electricity delivery to load only from this 1 KW wind turbine resulted to be between 1.6-17 MWh/yr.

scholarly journals Techno-economic analysis and modelling of the feasibility of wind energy in Kuwait

2022 ◽  
Vol 7 ◽  
pp. 9
Author(s):  
Seyed Amir Kaboli ◽  
Reyhaneh Nazmabadi
Keyword(s):  
Power Generation ◽  
Economic Analysis ◽  
Wind Energy ◽  
Wind Turbine ◽  
Wind Power ◽  
Power Plants ◽  
Clean Energy ◽  
Wind Power Generation ◽  
Generation Capacity ◽  
The Impact

There continues to be significant attention and investment in wind power generation, which can supply a high percentage of the global demand for renewable energy if harvested efficiently. The research study is based on techno-economic analysis of the feasibility of implementing wind power generation in Kuwait with a power generation capacity of 105 MW based on 50 wind turbines, which has a major requirement for clean energy. The study focused on three main areas of analysis and numerical modeling using the RETScreen software tool. The first area involved evaluating the performance and efficacy of generating wind power by collecting, analyzing, and modeling data on observed wind levels, wind turbine operation, and wind power generation. The second area comprised an environmental impact review to assess the environmental benefits of implementing wind power. The third area involved economic analysis of installing wind power in Kuwait. The analysis was undertaken to assess the energy recovery time for wind energy and determine the mitigation of global warming and pollution levels, the decrease of toxic emissions, and any cost savings from implementing clean energy systems in Kuwait. Additionally, sensitivity analysis was undertaken to determine the impact of certain variables in the modeling process. The results are used to estimate that the energy price would be $0.053 per kWh for a power generation capacity of 105 MWh based on an initial cost of $168 million and O&M of $5 million for 214,000 MWh of electricity exported to the grid. Moreover, the wind turbine farm will potentially avoid the emission of approximately 1.8 million tonnes of carbon dioxide per year, thereby saving approximately $9 million over 20 years spent installing carbon capture systems for conventional power plants. The wind farm containing a simple wind turbine is estimated to have a payback period of 9.1 years.

scholarly journals WIND POWER PLANT FOR THE NEEDS OF SMALL AGRICULTURAL FACILITIES

2020 ◽  
pp. 116-121
Author(s):  
Vаsіly Kоrdоnsky
Keyword(s):  
Wind Energy ◽  
Low Power ◽  
Wind Turbine ◽  
Wind Power ◽  
Power Plants ◽  
Wind Farm ◽  
Electrical Energy ◽  
Advantages And Disadvantages ◽  
Wind Power Plants ◽  
The Impact

There are many advantages of wind energy, including energy, environmental, economic. Relatively low investment in wind energy projects compared to traditional energy industries. The total kinetic energy of wind in the world can be estimated as 80 times higher than the total energy consumption by humans. And although only a certain fraction of this total can be used for energy needs, the future. The development of the technology itself has enormous potential. The article introduces and provides a brief analysis and historical background of existing designs of low-power wind power plants of the world's major manufacturers; the purpose of research on the proposed topic is indicated. Proposed and developed and described a promising scheme of a wind farm for the needs of small agricultural facilities, which makes it possible to receive electric current at low wind speeds in all natural and climatic zones of Ukraine. It has been established that low-power wind power plants are one of the promising areas for obtaining electrical energy and meeting the needs for small agricultural facilities. The proposed scheme for generating electrical energy. This design of a wind turbine can produce both DC and AC power for stand-alone or grid systems. The calculation of the wind turbine rotor diameter has been reduced. The advantages and disadvantages of wind energy in comparison with traditional energy industries are described. Brief conclusions are made on the proposed design of the wind farm, this will improve the environment, reducing the impact of anthropogenic factors on the environment and also, taking into account the constant increase in energy prices, save money, since such independent small wind farms allow small agricultural facilities to be provided with energy sources.

scholarly journals Techno-Economic Analysis and Modelling of the Feasibility of Wind Energy in Kuwait

2022 ◽  
Vol 4 (1) ◽  
pp. 14-34
Author(s):  
Ali M. H. A. Khajah ◽  
Simon P. Philbin
Keyword(s):  
Power Generation ◽  
Economic Analysis ◽  
Wind Energy ◽  
Wind Turbine ◽  
Wind Power ◽  
Power Plants ◽  
Clean Energy ◽  
Wind Power Generation ◽  
Environmental Benefits ◽  
The Impact

There continues to be significant attention and investment in wind power generation, which can supply a high percentage of the global demand for renewable energy if harvested efficiently. The research study is based on a techno-economic analysis of the feasibility of implementing wind power generation in Kuwait for 105 MW of electricity generation based on 50 wind turbines, which is a major requirement for clean energy. The study focused on three main areas of analysis and numerical modelling using the RETScreen software tool. The first area involved evaluating the performance and efficacy of generating wind power by collecting, analysing, and modelling data on observed wind levels, wind turbine operation, and wind power generation. The second area comprised an environmental impact report to assess the environmental benefits of implementing wind power. The third area involved economic analysis of installing wind power in Kuwait. The analysis was undertaken to determine the energy recovery time for wind energy and determine the mitigation of global warming and pollution levels, the decrease of toxic emissions, and any cost savings from implementing clean energy systems in Kuwait. Additionally, sensitivity analysis was undertaken to determine the impact of certain variables in the modelling process. The results were used to estimate that the energy price would be $0.053 per kWh for a power generation capacity of 105 MWh based on an initial cost of US $168 million and O&M of $5 million for 214,000 MWh of electricity exported to the grid. Moreover, the wind turbine farm will potentially avoid the emission of approximately 1.8 million t of carbon dioxide per year, thereby saving about $9 million over 20 years spent through installing carbon capture systems for conventional power plants. The wind farm is estimated to have a payback time of 9.1 years.

SHAPING OF AN AUTONOMOUS POWER SYSTEM FOR GUARANTEED POWER SUPPLY WITH THE PREDOMINANCE WIND ENERGY

2018 ◽  
pp. 28-50
Author(s):  
S. G. Ignatiev ◽  
S. V. Kiseleva
Keyword(s):  
Energy Storage ◽  
Wind Speed ◽  
Wind Energy ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Energy Demand ◽  
Diesel Generator ◽  
Average Wind Speed ◽  
Wind Speeds ◽  
Average Wind

Optimization of the autonomous wind-diesel plants composition and of their power for guaranteed energy supply, despite the long history of research, the diversity of approaches and methods, is an urgent problem. In this paper, a detailed analysis of the wind energy characteristics is proposed to shape an autonomous power system for a guaranteed power supply with predominance wind energy. The analysis was carried out on the basis of wind speed measurements in the south of the European part of Russia during 8 months at different heights with a discreteness of 10 minutes. As a result, we have obtained a sequence of average daily wind speeds and the sequences constructed by arbitrary variations in the distribution of average daily wind speeds in this interval. These sequences have been used to calculate energy balances in systems (wind turbines + diesel generator + consumer with constant and limited daily energy demand) and (wind turbines + diesel generator + consumer with constant and limited daily energy demand + energy storage). In order to maximize the use of wind energy, the wind turbine integrally for the period in question is assumed to produce the required amount of energy. For the generality of consideration, we have introduced the relative values of the required energy, relative energy produced by the wind turbine and the diesel generator and relative storage capacity by normalizing them to the swept area of the wind wheel. The paper shows the effect of the average wind speed over the period on the energy characteristics of the system (wind turbine + diesel generator + consumer). It was found that the wind turbine energy produced, wind turbine energy used by the consumer, fuel consumption, and fuel economy depend (close to cubic dependence) upon the specified average wind speed. It was found that, for the same system with a limited amount of required energy and high average wind speed over the period, the wind turbines with lower generator power and smaller wind wheel radius use wind energy more efficiently than the wind turbines with higher generator power and larger wind wheel radius at less average wind speed. For the system (wind turbine + diesel generator + energy storage + consumer) with increasing average speed for a given amount of energy required, which in general is covered by the energy production of wind turbines for the period, the maximum size capacity of the storage device decreases. With decreasing the energy storage capacity, the influence of the random nature of the change in wind speed decreases, and at some values of the relative capacity, it can be neglected.

scholarly journals Impact of the Wind Turbine on the Parameters of the Electricity Supply to an Agricultural Farm

2021 ◽  
Vol 13 (13) ◽  
pp. 7279
Author(s):  
Zbigniew Skibko ◽  
Magdalena Tymińska ◽  
Wacław Romaniuk ◽  
Andrzej Borusiewicz
Keyword(s):  
Power Plant ◽  
Wind Turbine ◽  
Wind Power ◽  
Rural Areas ◽  
Power Plants ◽  
Reactive Power ◽  
Supply Voltage ◽  
Common Source ◽  
Voltage Fluctuations ◽  
The Impact

Wind power plants are an increasingly common source of electricity located in rural areas. As a result of the high variability of wind power, and thus the generated power, these sources should be classified as unstable sources. In this paper, the authors attempted to determine the impact of wind turbine operation on the parameters of electricity supplied to farms located near the source. As a result of the conducted field tests, variability courses of the basic parameters describing the supply voltage were obtained. The influence of power plant variability on the values of voltage, frequency, and voltage distortion factor was determined. To estimate the capacity of the transmission lines, the reactive power produced in the power plant and its effect on the value of the power factor were determined. The conducted research and analysis showed that the wind power plant significantly influences voltage fluctuations in its immediate vicinity (the maximum value registered was close to 2%, while the value required by law was 2.5%). Although all the recorded values are within limits specified by the current regulations (e.g., the THD value is four times lower than the required value), wind turbines may cause incorrect operation of loads connected nearby. This applies mainly to cases where consumers sensitive to voltage fluctuations are installed in the direct vicinity of the power plant.

scholarly journals Tourist Viewshed Externalities and Wind Energy Production

2017 ◽  
Vol 46 (2) ◽  
pp. 224-241 ◽  
Author(s):  
Jacob R. Fooks ◽  
Kent D. Messer ◽  
Joshua M. Duke ◽  
Janet B. Johnson ◽  
Tongzhe Li ◽  
...  
Keyword(s):  
Wind Energy ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Energy Production ◽  
Hotel Room ◽  
Negative Effect ◽  
The Impact ◽  
Large Wind

This study uses an experiment where ferry passengers are sold hotel room “views” to evaluate the impact of wind turbines views on tourists’ vacation experience. Participants purchase a chance for a weekend hotel stay. Information about the hotel rooms was limited to the quality of the hotel and its distance from a large wind turbine, as well as whether or not a particular room would have a view of the turbine. While there was generally a negative effect of turbine views, this did not hold across all participants, and did not seem to be effected by distance or hotel quality.

scholarly journals Numerical and experimental investigations of the impacts of the integration of wind energy into distribution network

2021 ◽  
Author(s):  
◽  
Ramesh Kumar Behara
Keyword(s):  
Renewable Energy ◽  
Wind Energy ◽  
Wind Turbine ◽  
Wind Power ◽  
Distribution Systems ◽  
Electrical Power ◽  
Distribution Network ◽  
Experimental Investigations ◽  
Doubly Fed ◽  
The Impact

The growing needs for electric power around the world has resulted in fossil fuel reserves to be consumed at a much faster rate. The use of these fossil fuels such as coal, petroleum and natural gas have led to huge consequences on the environment, prompting the need for sustainable energy that meets the ever increasing demands for electrical power. To achieve this, there has been a huge attempt into the utilisation of renewable energy sources for power generation. In this context, wind energy has been identified as a promising, and environmentally friendly renewable energy option. Wind turbine technologies have undergone tremendous improvements in recent years for the generation of electrical power. Wind turbines based on doubly fed induction generators have attracted particular attention because of their advantages such as variable speed, constant frequency operation, reduced flicker, and independent control capabilities for maximum power point tracking, active and reactive powers. For modern power systems, wind farms are now preferably connected directly to the distribution systems because of cost benefits associated with installing wind power in the lower voltage networks. The integration of wind power into the distribution network creates potential technical challenges that need to be investigated and have mitigation measures outlined. Detailed in this study are both numerical and experimental models to investigate these potential challenges. The focus of this research is the analytical and experimental investigations in the integration of electrical power from wind energy into the distribution grid. Firstly, the study undertaken in this project was to carry out an analytical investigation into the integration of wind energy in the distribution network. Firstly, the numerical simulation was implemented in the MATLAB/Simulink software. Secondly, the experimental work, was conducted at the High Voltage Direct Centre at the University of KwaZulu-Natal. The goal of this project was to simulate and conduct experiments to evaluate the level of penetration of wind energy, predict the impact on the network, and propose how these impacts can be mitigated. From the models analysis, the effects of these challenges intensify with the increased integration of wind energy into the distribution network. The control strategies concept of the doubly fed induction generator connected wind turbine was addressed to ascertain the required control over the level of wind power penetration in the distribution network. Based on the investigation outcomes we establish that the impact on the voltage and power from the wind power integration in the power distribution system has a goal to maintain quality and balance between supply and demand.

The Suitability of Fly Ash for Use in Concrete According to EN 450 Based on their Particle Size

2018 ◽  
Vol 276 ◽  
pp. 110-115
Author(s):  
Martin Ťažký ◽  
Martin Labaj ◽  
Rudolf Hela
Keyword(s):  
Fly Ash ◽  
Power Plants ◽  
Catalytic Reduction ◽  
Raw Materials ◽  
Thermal Power ◽  
Combustion Process ◽  
Thermal Power Plants ◽  
Mechanical Parameters ◽  
Fly Ashes ◽  
The Impact

The by-products of energy industry are nowadays often affected by new limits governing the production of harmful gases discharged into the air. These stricter and stricter criteria are often met by electricity producers by changing the combustion process in thermal power plants itself. Nowadays, the SNCR (selective non-catalytic reduction) application is quite common in the combustion process in order to help reduce the nitrogen oxide emission. This article deals with the primary measures of thermal power plants, which in particular consist of a modified treatment of raw materials (coal) entering the combustion process. These primary measures then often cause the formation of fly ash with unsuitable fineness for the use in concrete according to EN 450. The paper presents the comparison of the physico-mechanical parameters of several fly ashes with a different fineness values. The primary task is to assess the impact of non-suitable granulometry in terms of EN 450 on the other physico-mechanical parameters of fly ashes sampled within the same thermal power plant. Several fly ashes produced in the Czech Republic and surrounding countries were evaluated in this way.

The Impact of Ice Formation on Wind Turbine Performance and Aerodynamics

2011 ◽  
Vol 133 (1) ◽  
Author(s):  
S. Barber ◽  
Y. Wang ◽  
S. Jafari ◽  
N. Chokani ◽  
R. S. Abhari
Keyword(s):  
Wind Energy ◽  
Wind Turbine ◽  
Swiss Alps ◽  
Test Facility ◽  
Ice Formation ◽  
Predictive Tool ◽  
Lower Altitude ◽  
Turbine Performance ◽  
The Impact ◽  
Power Curves

Wind energy is the world’s fastest growing source of electricity production; if this trend is to continue, sites that are plentiful in terms of wind velocity must be efficiently utilized. Many such sites are located in cold, wet regions such as the Swiss Alps, the Scandinavian coastline, and many areas of China and North America, where the predicted power curves can be of low accuracy, and the performance often deviates significantly from the expected performance. There are often prolonged shutdown and inefficient heating cycles, both of which may be unnecessary. Thus, further understanding of the effects of ice formation on wind turbine blades is required. Experimental and computational studies are undertaken to examine the effects of ice formation on wind turbine performance. The experiments are conducted on a dynamically scaled model in the wind turbine test facility at ETH Zurich. The central element of the facility is a water towing tank that enables full-scale nondimensional parameters to be more closely matched on a subscale model than in a wind tunnel. A novel technique is developed to yield accurate measurements of wind turbine performance, incorporating the use of a torquemeter with a series of systematic measurements. These measurements are complemented by predictions obtained using a commercial Reynolds-Averaged Navier–Stokes computational fluid dynamics code. The measured and predicted results show that icing typical of that found at the Guetsch Alpine Test Site (2330 m altitude) can reduce the power coefficient by up to 22% and the annual energy production (AEP) by up to 2%. Icing in the blade tip region, 95–100% blade span, has the most pronounced effect on the wind turbine’s performance. For wind turbines in more extreme icing conditions typical of those in Bern Jura, for example, icing can result in up to 17% losses in AEP. Icing at high altitude sites does not cause significant AEP losses, whereas icing at lower altitude sites can have a significant impact on AEP. Thus, the classification of icing is a key to the further development of prediction tools. It would be advantageous to tailor blade heating for prevention of ice buildup on the blade’s tip region. An “extreme” icing predictive tool for the project development of wind farms in regions that are highly susceptible to icing would be beneficial to wind energy developers.

scholarly journals Combining Wind and Pumped Hydro Energy Storage for Renewable Energy Generation in Ireland

2014 ◽  
Vol 2014 ◽  
pp. 1-6 ◽  
Author(s):  
Alice Coburn ◽  
Eilín Walsh ◽  
Patrick J. Solan ◽  
Kevin P. McDonnell
Keyword(s):  
Renewable Energy ◽  
Energy Storage ◽  
Wind Energy ◽  
Power Plants ◽  
Wind Farms ◽  
Energy Generation ◽  
Western Coast ◽  
Hydroelectric Power ◽  
Wind Potential ◽  
Renewable Energy Generation

Ireland has one of the highest wind energy potentials in Europe. The intermittent nature of wind makes this renewable resource impractical as a sole source of energy. Combining wind energy with pumped hydro energy storage (PHES) can overcome this intermittency, consuming energy during low-demand periods and supplying energy for periods of high demand. Currently Ireland has a number of hydroelectric power plants and wind farms of various scales in operation. A feasibility study was conducted to investigate the potential of securing a reliable source of renewable energy by increasing the penetration of hydroelectric power by means of combined wind-PHES developments. The greatest wind potential is experienced along the western coast of Ireland and a number of sites were identified here which satisfied a minimum mean wind speed criterion of 10.5 ms−1. Each site was then further evaluated according to topographical requirements for PHES. All but two of the identified sites are immediately unsuitable due to the presence of areas protected under European legislation; this highlights the nonenergy related obstacles in the path of renewable energy generation in Ireland and suggests that a compromise should be researched which could facilitate both renewable energy generation and species and habitat protection in Europe.

Sign in / Sign up

Export Citation Format

Share Document