scholarly journals Influence of SiO2/Al2O3 Molar Ratio on Phase Composition and Surfaces Quality of Aluminum Silicate Sanitary Glazes in the SiO2-Al2O3-CaO-Na2O System

2016 ◽  
Vol 61 (4) ◽  
pp. 1739-1746 ◽  
Author(s):  
M. Leśniak ◽  
J. Partyka ◽  
M. Sitarz
Keyword(s):  
Surface Roughness ◽  
Phase Composition ◽  
Surface Quality ◽  
Glass Ceramic ◽  
Glass Phase ◽  
Molar Ratio ◽  
Aluminum Silicate

Abstract This paper presents the results of research on aluminum silicate sanitary glazes in the SiO2-Al2O3-CaO-Na2O system with different SiO2/Al2O3 molar ratio. XRD, SEM-EDS and FITR measurement indicated that SiO2/Al2O3 molar ratio has a significant impact on the phase composition of the obtained glazes. Glass-ceramic glazes were obtained that consisted of both the glass phase and pseudowollastonite (Ca3[SiO3]3) or anorthite (Ca[Al2Si2O8]) crystals. Subsequently, the influence of phase composition on surface quality (roughness) was examined for the obtained samples. On the basis of the conducted examination of glaze surface roughness was observed that glazes of extreme SiO2/Al2O3 molar ratio are characterized with greatest surface roughness when compared to other glazes.

Observation in the Surface Roughness of Silicon Wafer during Semi-Fixed Abrasive Machining with Large Grains

2009 ◽  
Vol 69-70 ◽  
pp. 253-257
Author(s):  
Ping Zhao ◽  
Jia Jie Chen ◽  
Fan Yang ◽  
K.F. Tang ◽  
Ju Long Yuan ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Silicon Wafer ◽  
Processing Parameters ◽  
Wafer Surface ◽  
Abrasive Machining ◽  
Fixed Abrasive ◽  
Is Failure ◽  
Better Than

Semi-fixed abrasive is a novel abrasive. It has a ‘trap’ effect on the hard large grains that can prevent defect effectively on the surface of the workpiece which is caused by large grains. In this paper, some relevant experiments towards silicon wafers are carried out under the different processing parameters on the semi-fixed abrasive plates, and 180# SiC is used as large grains. The processed workpieces’ surface roughness Rv are measured. The experimental results show that the surface quality of wafer will be worse because of higher load and faster rotating velocity. And it can make a conclusion that the higher proportion of bond of the plate, the weaker of the ‘trap’ effect it has. Furthermore the wet environment is better than dry for the wafer surface in machining. The practice shows that the ‘trap’ effect is failure when the workpiece is machined by abrasive plate which is 4.5wt% proportion of bond in dry lapping.

The mechanism of process parameters influencing the AlSi10Mg side surface quality fabricated via laser powder bed fusion

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Shimin Dai ◽  
Hailong Liao ◽  
Haihong Zhu ◽  
Xiaoyan Zeng
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Process Parameters ◽  
Laser Power ◽  
Side Surface ◽  
Laser Powder Bed Fusion ◽  
Scanning Velocity ◽  
Content Type ◽  
Powder Bed

Purpose For the laser powder bed fusion (L-PBF) technology, the side surface quality is essentially important for industrial applicated parts, such as the inner flow parts. Contour is generally adopted at the parts’ outline to enhance the side surface quality. However, the side surface roughness (Ra) is still larger than 10 microns even with contour in previous studies. The purpose of this paper is to study the influence of contour process parameters, laser power and scanning velocity on the side surface quality of the AlSi10Mg sample. Design/methodology/approach Using L-PBF technology to manufacture AlSi10Mg samples under different contour process parameters, use a laser confocal microscope to capture the surface information of the samples, and obtain the surface roughness Ra and the maximum surface height Rz of each sample after analysis and processing. Findings The results show that the side surface roughness decreases with the increase of the laser power at the fixed scanning velocity of 1,000 mm/s, the side surface roughness Ra stays within the error range as the contour velocity increases. It is found that the Ra increases with the scanning velocity increasing and the greater the laser power with the greater Ra increases when the laser power of contour process parameters is 300 W, 350 W and 400 W. The Rz maintain growth with the contour scanning velocity increasing at constant laser power. The continuous uniform contour covers the pores in the molten pool of the sample edge and thus increase the density of the sample. Two mechanisms named “Active adhesion” and “Passive adhesion” cause sticky powder. Originality/value Formation of a uniform and even contour track is key to obtain the good side surface quality. The side surface quality is determined by the uniformity and stability of the contour track when the layer thickness is fixed. These research results can provide helpful guidance to improve the surface quality of L-PBF manufactured parts.

Investigation of the Effects of Technological Parameters on Surface Roughness in Extrusion Bars of Aluminum Alloy

2019 ◽  
Vol 889 ◽  
pp. 155-160
Author(s):  
Trong Mai Nguyen ◽  
Đuc Quy Tran ◽  
Van Nghe Pham ◽  
Van Canh Nguyen
Keyword(s):  
Surface Roughness ◽  
Aluminum Alloy ◽  
Surface Quality ◽  
Research Work ◽  
Extrusion Process ◽  
Optimal Parameters ◽  
Technological Parameters

In this research work, the result of the effects of technological parameters on surface roughness in extrusion bars of aluminum alloy were pesented. The results of this study may be used for choosing optimal parameters of extrusion process so that surface quality of extruded bar was improved.

scholarly journals Impact of Structural Defects on the Surface Quality of Hardwood Species Sliced Veneers

2020 ◽  
Vol 10 (18) ◽  
pp. 6265
Author(s):  
Vasiliki Kamperidou ◽  
Efstratios Aidinidis ◽  
Ioannis Barboutis
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Wood Species ◽  
Research Work ◽  
Structural Defects ◽  
Material Surface ◽  
Typical Structure ◽  
Hardwood Species ◽  
The Impact

The surface roughness constitutes one of the most critical properties of wood and wood veneers for their extended utilization, affecting the bonding ability of the veneers with one another in the manufacturing of wood composites, the finishing, coating and preservation processes, and the appearance and texture of the material surface. In this research work, logs of five significant European hardwood species (oak, chestnut, ash, poplar, cherry) of Balkan origin were sliced into decorative veneers. Their surface roughness was examined by applying a stylus tracing method, on typical wood structure areas of each wood species, as well as around the areas of wood defects (knots, decay, annual rings irregularities, etc.), to compare them and assess the impact of the defects on the surface quality of veneers. The chestnut veneers presented the smoothest surfaces, while ash veneers, despite the higher density, recorded the highest roughness. In most of the cases, the roughness was found to be significantly lower around the defects, compared to the typical structure surfaces, probably due to lower porosity, higher density and the presence of tensile wood. The results reveal that the presence of defects does not affect the roughness of the veneers and increases neither the processing requirements of the veneer sheets before finishing, nor the respective production cost of veneers and the veneer-based wood panels. The high utilization prospects of the examined wood species in veneer production, even those bearing various defects, is highlighted.

scholarly journals Surface Roughness Investigation of Poly-Jet 3D Printing

Mathematics ◽  
2020 ◽  
Vol 8 (10) ◽  
pp. 1758
Author(s):  
Nectarios Vidakis ◽  
Markos Petousis ◽  
Nikolaos Vaxevanidis ◽  
John Kechagias
Keyword(s):  
Surface Roughness ◽  
3D Printing ◽  
Surface Quality ◽  
Back Propagation ◽  
Physical Models ◽  
Layer By Layer ◽  
Linear Regression Models ◽  
Feed Forward Back Propagation ◽  
The Impact

An experimental investigation of the surface quality of the Poly-Jet 3D printing (PJ-3DP) process is presented. PJ-3DP is an additive manufacturing process, which uses jetted photopolymer droplets, which are immediately cured with ultraviolet lamps, to build physical models, layer-by-layer. This method is fast and accurate due to the mechanism it uses for the deposition of layers as well as the 16 microns of layer thickness used. Τo characterize the surface quality of PJ-3DP printed parts, an experiment was designed and the results were analyzed to identify the impact of the deposition angle and blade mechanism motion onto the surface roughness. First, linear regression models were extracted for the prediction of surface quality parameters, such as the average surface roughness (Ra) and the total height of the profile (Rt) in the X and Y directions. Then, a Feed Forward Back Propagation Neural Network (FFBP-NN) was proposed for increasing the prediction performance of the surface roughness parameters Ra and Rt. These two models were compared with the reported ones in the literature; it was revealed that both performed better, leading to more accurate surface roughness predictions, whilst the NN model resulted in the best predictions, in particular for the Ra parameter.

scholarly journals Rotary Ultrasonic Machining of Alumina Ceramic: An Experimental Investigation of Tool Path and Tool Overlapping

2020 ◽  
Vol 10 (5) ◽  
pp. 1667 ◽  
Author(s):  
Basem M. A. Abdo ◽  
Abdualziz El-Tamimi ◽  
Emad Abouel Nasr
Keyword(s):  
Surface Roughness ◽  
Surface Morphology ◽  
Surface Quality ◽  
Tool Path ◽  
Removal Rate ◽  
Ultrasonic Machining ◽  
Rotary Ultrasonic Machining ◽  
Roughness Surface ◽  
Tool Wear Mechanisms

Pocket milling has been regarded as one of the most widely used operations in machining. The surface quality of the machined pockets is an essential aspect of any engineering and medical applications. In the current study, rotary ultrasonic machining (RUM) was applied for milling micro-pockets on alumina (Al2O3) ceramic. The objective of this research was to analyze the effect of the tool overlapping parameters on the surface roughness, surface morphology and the profiles of the machined pockets. Subsequently, the effect of different tool path strategies was analyzed on the surface quality and the material removal rate (MRR) of the machined pockets. A scanning electron microscope is used for analyzing the tool wear mechanisms. The experimental results provide evidence that the surface roughness, surface morphology and the MRR have been significantly affected by the considered tool overlapping and the tool path strategies. Furthermore, among the selected tool overlapping parameters (5–25%) and the tool path strategies, the best surface roughness (Ra = 0.155 μm and Rt = 1.432 µm) of the machined pockets can be found at 20% of the tool overlapping with a mix of uni-directional and zigzag tool path strategy.

ANALYSIS OF THE CORRELATION BETWEEN FRACTAL STRUCTURE OF CUTTING FORCE SIGNAL AND SURFACE ROUGHNESS OF MACHINED WORKPIECE IN END MILLING OPERATION

Fractals ◽  
2019 ◽  
Vol 27 (02) ◽  
pp. 1950013 ◽  
Author(s):  
AHMAD THUFFAIL THASTHAKEER ◽  
ALI AKHAVAN FARID ◽  
CHANG TECK SENG ◽  
HAMIDREZA NAMAZI
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Surface Quality ◽  
Cutting Forces ◽  
End Milling ◽  
Complex Structure ◽  
Machined Surface ◽  
End Mills ◽  
Machining Operations

Analysis of the machined surface is one of the major issues in machining operations. On the other hand, investigating about the variations of cutting forces in machining operation has great importance. Since variations of cutting forces affect the surface quality of machined workpiece, therefore, analysis of the correlation between cutting forces and surface roughness of machined workpiece is very important. In this paper, we employ fractal analysis in order to investigate about the complex structure of cutting forces and relate them to the surface quality of machined workpiece. The experiments have been conducted in different conditions that were selected based on cutting depths, type of cutting tool (serrated versus. square end mills) and machining conditions (wet and dry machining). The result of analysis showed that among all comparisons, we could only see the correlation between complex structure of cutting force and the surface roughness of machined workpiece in case of using serrated end mill in wet machining condition. The employed methodology in this research can be widely applied to other types of machining operations to analyze the effect of variations of different parameters on variability of cutting forces and surface roughness of machined workpiece and then investigate about their correlation.

EVALUATION OF A REGRESSION PREDICTION MODEL FOR SURFACE ROUGHNESS OF WOOD–POLYETHYLENE COMPOSITE (WPC)

2017 ◽  
Vol 24 (Supp02) ◽  
pp. 1850033
Author(s):  
WENYONG SHI ◽  
YAN MA ◽  
CHUNMEI YANG ◽  
BIN JIANG ◽  
ZHE LI
Keyword(s):  
Surface Roughness ◽  
Surface Morphology ◽  
Prediction Model ◽  
Surface Quality ◽  
Cutting Parameters ◽  
Wood Powder ◽  
Polyethylene Composite ◽  
Milled Surface ◽  
Powder Content

Milling processing is an important way to obtain wood–polyethylene composite (WPC) end products. In order to improve the processing efficiency and surface quality of WPC and meet the practical application requirements, this paper focussed on morphology and roughness of the WPC-milled surface and studied surface quality changes under different cutting parameters and milling methods through multi-parameters milling experiments. The milling surface morphology and roughness of WPC were analyzed and measured during cut-in, cutting and cut-out sections. It also revealed the affect rule of different cutting parameters and milling methods on milled surface morphology and roughness. The results show that the milling surface roughness of WPC products with wood powder content of 70% is significantly larger than the one whose wood powder content is 60%, and defects such as holes are also relatively more. Finally, a surface roughness prediction model was established based on the mathematical regression method and its multi-factor simulation was carried out. A comparative analysis of predictive and experimental values was performed to verify the reliability of the model. It could also provide theoretical guidance and technical guarantee for high processing quality of WPC milling and cutting.

A Study on Surface Quality of GaN with CMP Polishing Process

2011 ◽  
Vol 291-294 ◽  
pp. 1764-1767
Author(s):  
Wei Li ◽  
Ming Ming Ma ◽  
Bin Hu
Keyword(s):  
Surface Roughness ◽  
Particle Size ◽  
Gallium Nitride ◽  
Surface Quality ◽  
Chemical Reaction ◽  
Experimental Result ◽  
Precision Machining ◽  
Polishing Process

This paper introduced a polishing process for planarization of gallium nitride (GaN) wafer by polishing slurry that is made up by the chemical reaction with H2O2 solution and iron. Some different polishing parameters in the polishing process has been analyzed, which affect the surface quality of wafers, such as slurry particle size, polishing times, polishing slurry etc., and trying to improve the polishing process by optimization of the polishing parameters. The experimental result showed that this polishing method has an effect on the surface quality of GaN wafers, finally, the efficient and precision machining with surface roughness of GaN wafers of Ra0.81 nm has been gained by the CMP polishing process.

scholarly journals Adhesion Strength of Cellulosic Varnish Coated Wood Species as Function of Their Surface Roughness

2015 ◽  
Vol 2015 ◽  
pp. 1-5 ◽  
Author(s):  
Turgay Ozdemir ◽  
Salim Hiziroglu ◽  
Mutlu Kocapınar
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Adhesion Strength ◽  
Wood Species ◽  
Alnus Glutinosa ◽  
Coating Process ◽  
Fagus Orientalis ◽  
Abies Nordmanniana ◽  
Grain Orientations

The objective of this study was to evaluate adhesion strength of four wood species, namely, beech (Fagus orientalisLipsky), alder (Alnus glutinosasubsp.barbataYalt.), spruce (Picea orientalisL. Link), and fir (Abies nordmannianasubsp.) coated with cellulosic varnish. Samples were prepared in tangential and radial grain orientations from the above species. Surface quality of the specimens was also measured employing stylus type equipment after samples of all four types of species were sanded with 80- and 180-grit sandpaper prior to coating process. Surface roughness of the specimens sanded with 80-grit sandpaper resulted in significantly higher mean peak-to-valley height (Rz) values based on the measurement employing stylus type profilometer. The highest adhesion strength values of 2.39 N/mm2and 2.03 N/mm2were found for beech and alder samples, respectively. It appears that overall higher roughness characteristics of the specimens exhibited enhanced adherence between substrate and varnish resulting in higher adhesion strength values.

Sign in / Sign up

Export Citation Format

Share Document