scholarly journals Experimental determination and modeling of flow curves of xanthan gum solutions over a large range of shear rates

2021 ◽  
Vol 31 (1) ◽  
pp. 24-38
Author(s):  
Julian Sepulveda ◽  
Agnes Montillet ◽  
Dominique Della Valle ◽  
Thanina Amiar ◽  
Hubert Ranchon ◽  
...  

Abstract The viscosities of solutions formulated with xanthan gum and xanthan gum with whey protein isolates are experimentally characterized and modeled over a wide range of shear rates [10−3 to 105 s−1]. As shown by numerous studies [1, 2], the generation of vortices in the cone-plate geometry is making viscosity measurements beyond a certain shear rate unreliable. In the present work, an innovative technique, based on microfluidics and developed by the company Formulaction, has been employed to extend to high shear rates, the viscosity flow curve obtained with a rotational rheometer. The main highlights of this study are firstly, to propose a scaling law for the inertial transition in the cone-plate geometry for different diameters and angles through the determination of the maximum shear rate at which one can expect a true viscosity value. Secondly, the high shear rate measurements allow the determination of the second Newtonian plateau for these solutions thanks to the Williams-Carreau model. An attempt for the second plateau modeling is proposed following the concept of an intrinsic viscosity in the high shear equilibrium. In the same way, other fitted parameters from the Williams-Carreau law are modeled as a function of the polymer concentration. This procedure allows to provide a predictive model for the rheological behavior of xanthan gum-based solutions used in high shear processes like high pressure homogenization, emulsification, foaming, microfluidics, etc in food, pharmaceutical or cosmetics applications.

1967 ◽  
Vol 40 (5) ◽  
pp. 1483-1491
Author(s):  
Yoshio Ito

Abstract Nonnewtonian flow of poly(dimethyl siloxanes) of various molecular weights has been studied with a short capillary viscosimeter. The experiment covered a wide range of shear rate, from 10−1 to 3×106sec−1. Results were as follows: (1) Flow behavior of the sample changes with the degree of polymerization. For siloxanes with degrees of polymerization less than 1.55×102, flow of the fluid is newtonian throughout the whole range of shear rates; for siloxanes with degrees of polymerization from 3.22×102 to 2.63×103, flow is nonnewtonian at moderate shear rates; it again becomes newtonian at high shear rates. With degrees of polymerization more than 3.31×103, the spiral flow rises to a high shear rate. (2) Plow behavior of the samples is expressed by modifying Shishido's equation proposed for nonnewtonian polymer solutions. (3) When the observed flow curve contains its inflection point, the upper newtonian viscosity can be estimated by a new method proposed here. (4) The relations among the end correction of capillary, the pressure loss, and the shear stress proposed by Shishido for polymer solutions are applicable to poly(dimethy! siloxane) also.


1990 ◽  
Vol 112 (3) ◽  
pp. 417-425 ◽  
Author(s):  
C. S. Peter Wu ◽  
T. Melodick ◽  
S. C. Lin ◽  
J. L. Duda ◽  
E. E. Klaus

A high-shear capillary viscometer was used to determine the viscosity of mineral oil lubricants containing an olefin copolymer up to shear rates of a million reciprocal seconds. Comprehensive measurements were conducted for a range of polymer concentrations from 1–3 wt percent polymer and a temperature range of 38–120° C. The experimental technique utilizes a theoretical analysis procedure to handle the complications associated with viscous heating, the influence of pressure on the viscosity, and the excess pressure drop which occur at the entrance and exit of the capillary. The viscosity of the polymer solutions is determined over the complete range of shear rate starting from the lower Newtonian limit, through the shear-thinning region, and finally, the Newtonian behavior at high shear rates. It is shown that the standard ASTM plot for viscosity-temperature behavior can be used to correlate the viscous behavior for a given polymer concentration over this broad range of shear rates and shear stresses.


2021 ◽  
Vol 249 ◽  
pp. 03012
Author(s):  
Lu Jing ◽  
Julio M. Ottino ◽  
Richard M. Lueptow ◽  
Paul B. Umbanhowar

Particle segregation in geophysical and industrial granular flows is typically driven by gravity and shear. While gravity-induced segregation is relatively well understood, shear-induced segregation is not. In particular, what controls segregation in the absence of gravity and the interplay between shearand gravity-driven segregation remain unclear. Here, we explore the shear-induced segregation force on an intruder particle in controlled-velocity granular flows where the shear profile is systematically varied. The shear-induced segregation force is found to be proportional to the shear rate gradient, which effectively pushes the large intruder from lower to higher shear rate regions. A scaling law is developed for the segregation force that is accurate over a wide range of overburden pressures and shear rates, and hence inertial numbers.


2011 ◽  
Vol 106 (12) ◽  
pp. 1062-1068 ◽  
Author(s):  
Naoki Tsuji ◽  
Yuko Honda ◽  
Chikako Kamisato ◽  
Yoshiyuki Morishima ◽  
Toshiro Shibano ◽  
...  

SummaryEdoxaban is an oral, direct factor Xa (FXa) inhibitor under late-phase clinical development. This study compared the antithrombotic efficacy of edoxaban with that of an indirect FXa inhibitor, fondaparinux, in in vivo venous and arterial thrombosis models and in ex vivo perfusion chamber thrombosis model under low and high shear rates in rats. Venous and arterial thrombi were induced by platinum wire insertion into the inferior vena cava and by application of FeCl3 to the carotid artery, respectively. The perfusion chamber thrombus was formed by blood perfusion into a collagen-coated capillary at 150 s-1 (low shear rate) and 1,600 s-1 (high shear rate). Effective doses of edoxaban that reduced thrombus formation by 50% (ED50) in venous and arterial thrombosis models were 0.076 and 0.093 mg/kg/h, respectively. In contrast, ED50 of fondaparinux in the arterial thrombosis model (>10 mg/kg/h) was markedly higher compared to ED50 in the venous thrombosis model (0.021 mg/kg/h). In the perfusion chamber thrombosis model, the ratio of ED50 under high shear rate (1.13 mg/kg/h) to that under low shear rate (0.63 mg/kg/h) for edoxaban was 1.9, whereas that for fondaparinux was more than 66. While the efficacy of fondaparinux markedly decreased in arterial thrombosis and in a high-shear state, edoxaban exerted consistent antithrombotic effects regardless of flow conditions. These results suggest that shear rate is a key factor in different antithrombotic effects between edoxaban and fondaparinux.


Blood ◽  
1987 ◽  
Vol 70 (4) ◽  
pp. 1214-1217
Author(s):  
E Fressinaud ◽  
D Baruch ◽  
C Rothschild ◽  
HR Baumgartner ◽  
D Meyer

Although it is well established that plasma von Willebrand Factor (vWF) is essential to platelet adhesion to subendothelium at high shear rates, the role of platelet vWF is less clear. We studied the respective role of both plasma and platelet vWF in mediating platelet adhesion to fibrillar collagen in a parallel-plate perfusion chamber. Reconstituted blood containing RBCs, various mixtures of labeled washed platelets and plasma from controls or five patients with severe von Willebrand disease (vWD), was perfused through the chamber for five minutes at a shear rate of 1,600 s-1. Platelet-collagen interactions were estimated by counting the radioactivity in deposited platelets and by quantitative morphometry. When the perfusate consisted of normal platelets suspended in normal plasma, platelet deposition on the collagen was 24.7 +/- 3.6 X 10(6)/cm2 (mean +/- SEM, n = 6). Significantly less deposition (16 +/- 2.3) was observed when vWD platelets were substituted for normal platelets. In mixtures containing vWD plasma, significantly greater deposition (9 +/- 2.2) was obtained with normal than with vWD platelets (1 +/- 0.4) demonstrating a role for platelet vWF in mediating the deposition of platelets on collagen. Morphometric analysis confirmed these data. Our findings indicate that platelet, as well as plasma, vWF mediates platelet-collagen interactions at a high shear rate.


2021 ◽  
Vol 15 (3) ◽  
pp. 181-190
Author(s):  
Elif H Ozcan Cetin ◽  
Mehmet S Cetin ◽  
Mustafa B Ozbay ◽  
Hasan C Könte ◽  
Nezaket M Yaman ◽  
...  

Aim: We aimed to assess the association of whole blood with thromboembolic milieu in significant mitral stenosis patients. Methodology & results: We included 122 patients and classified patients into two groups as having thrombogenic milieu, thrombogenic milieu (+), otherwise patients without thrombogenic milieu, thrombogenic milieu (-). Whole blood viscosity (WBV) in both shear rates were higher in thrombogenic milieu (+) group comparing with thrombogenic milieu (-). WBV at high shear rate and WBV at low shear rate parameters were moderately correlated with grade of spontaneous echo contrast. Adjusted with other parameters, WBV parameters at both shear rates were associated with presence of thrombogenic milieu. Discussion & conclusion: We found that extrapolated WBV at both shear rates was significantly associated with the thrombogenic milieu in mitral stenosis. This easily available parameter may provide additional perspective about thrombogenic diathesis.


1976 ◽  
Vol 55 (3) ◽  
pp. 353-356 ◽  
Author(s):  
M. Braden ◽  
Ratna Perera

Six commercial fluoride gels have been studied, using a cone and plate viscometer. Also, the thickening agents have been analyzed using infrared spectroscopy. All gels showed stress thinning, which is the decrease of viscosity with shear rate. Such shear rate dependence is clinically convenient in that the gel will flow readily at the high shear stresses present when the gel is applied but will not flow readily under its own weight when on the tooth. Five materials containing hydroxyalkyl celluloses showed similar degrees of shear thinning. One material with a non-cellulosic thickener showed much more extreme stress thinning together with elastic behavior at low shear rates; such behavior may be clinically advantageous. All of the gels showed only slight temperature dependence of rheological properties.


1992 ◽  
Vol 289 ◽  
Author(s):  
John R. Melrose

AbstractAn overview is given of theories of aggregates under flow. These generally assume some sort of structural breakdown as the shear rate is increased. Models vary with both the rigidity of the bonding and the level of treatment of hydrodynamics. Results are presented for simulations of a Rouse model of non-rigid, (i.e. central force) weakly bonded aggregates. In large scale simulations different structures are observed at low and high shear rates. The change from one structure to another is associated with a change in the rate of shear thinning. The model captures low shear rate features of real systems absent in previous models: this feature is ascribed to agglomerate deformations. Quantitatively, the model is two orders of magnitude out from experiment but some scaling is possible.


Processes ◽  
2020 ◽  
Vol 8 (12) ◽  
pp. 1622
Author(s):  
Sahr Sana ◽  
Vladimir Zivkovic ◽  
Kamelia Boodhoo

Spinning disc technology is capable of achieving intensified micromixing within thin liquid films created through large shear rates, typically of the order of 103 s−1, generated by means of fast disc surface rotation. In this study the effect of the high shear on solvent–antisolvent mixing and starch nanoparticle precipitation is reported. Rheological studies of starch solutions at 2% w/v and 4% w/v have demonstrated their shear-thinning behaviour at the large shear rates experienced on the spinning disc surface. The effect of such high shear rate on starch nanoparticle precipitation is investigated alongside solute concentration and several other operating parameters such as flow rate, disc rotational speed, and solvent/antisolvent ratio. A reduction in nanoparticle size has been observed with an increase in starch concentration, although agglomeration was found to be more prevalent amongst these smaller particles particularly at larger flow rates and disc rotational speeds. Micromixing time, estimated on the basis of an engulfment mechanism, has been correlated against shear rate. With fast micromixing of the order of 1 ms observed at higher shear rates, and which are practically unaffected by the starch concentrations used, micromixing is not thought to be influential in determining the particle characteristics highlighted in this work.


Blood ◽  
2012 ◽  
Vol 120 (21) ◽  
pp. 3300-3300
Author(s):  
Reginald Tran ◽  
Byungwook AHN ◽  
David R Myers ◽  
Yongzhi Qiu ◽  
Yumiko Sakurai

Abstract Abstract 3300 Background: Hemostasis is an important physiologic process that requires the aggregation of platelets at distinct sites of vascular injury to promote clot formation and prevent blood loss. Platelet response to soluble agonists and shear stress has been studied extensively, but little is known of how microenvironmental geometry affects platelet function. As platelets must quickly adhere to, aggregate, and initiate coagulation only at the affected areas, spatial cues must at some level regulate this process. This aspect of spatial regulation has been investigated under static conditions by our group and others (Kita et al., 2011; Van de Walle et al., 2012). Understanding this aspect of platelet function is vital for better understanding the process of hemostasis and pathophysiological conditions such as thrombosis. Here, we directly examine how spatial cues affect platelet aggregation and physiology under variable shear conditions by flowing heparinized whole blood over micropatterned collagen in a microfluidic channel. This system allows us to assess platelet aggregate morphology under different geometric constraints and shear rates, as well as evaluate platelet physiology at the single cell level by measuring calcium signaling using fluorogenic dyes. Results: A microfluidic channel was bonded to a glass coverslip stamped with FITC-conjugated Type I collagen using a novel technique combining microcontact printing and the stamp-stick bonding technique (Satyanarayana et al., 2005). Before flowing, each chamber was incubated with 1% bovine serum albumin (BSA) blocking solution for 1.5 hours. Whole heparinized blood was then flowed through the chamber at shear rates of 100, 1000, and 10000 s−1. Platelets were labeled with Fura Red, and time lapse confocal imaging was performed for 10 minutes to monitor the aggregation of platelets at the start of flow. The flow chambers were then flushed with Tyrode's buffer with 0.1% BSA using the same experimental shear rates until the chamber was cleared of red blood cells. Image analysis was conducted using ImageJ (to calculate the percentage of platelet coverage on the collagen stamps at different shear rates. Platelets initially adhere to the distal edge of the collagen micropatterns for all shear rates (Fig. 1), indicating that platelets may require a priming region before forming a stable adhesion. As shear rate increased, platelet coverage of the collagen stamps decreased. However, aggregates also grew without conforming to the geometric constraints imposed by the collagen micropatterns more frequently at those higher shear rates (Fig. 1). Though platelet tethers generally aligned in the direction of the flow, increased tether lengths could be seen when platelets were exposed to higher shear, which may explain why platelets were able to span larger gaps and aggregate in a less spatially constrained manner at high shear rates. Image analysis shows that 51.5% of the collagen was covered by platelet aggregates for a shear rate of 100 s−1 with some platelets forming tethers to span gaps (Fig. 2). When the shear rate was increased to 1000 s−1, platelet coverage of the collagen microstamp drastically dropped to 18.5% (Fig. 2). At a pathophysiological shear rate of 10000 s−1, the percentage of collagen covered by platelets dropped further to 12.8% and adopted a linear shape, although a large portion of the aggregate can be seen spanning gaps between the collagen microstamp (Fig. 1 and 2). Conclusions and Ongoing Efforts: Ours is the first reported study of the spatial regulation of platelet aggregation under variable shear in a microfluidic channel. We have found that platelets are more spatially regulated under low shear conditions compared to high shear, which has implications for thrombosis and other clotting disorders. Future studies will incorporate the simultaneous use of ratiometric fluorgenic calcium signaling dyes to investigate the role of spatial regulation in Ca2+ signaling. Finally, we have developed a method to culture endothelial cells around a collagen micropattern to study this spatial regulation of platelet function under more physiological conditions (Fig. 3). Disclosures: No relevant conflicts of interest to declare.


Sign in / Sign up

Export Citation Format

Share Document