scholarly journals A Feature Extraction Method for Vibration Signal of Bearing Incipient Degradation

2016 ◽  
Vol 16 (3) ◽  
pp. 149-159 ◽  
Author(s):  
Haifeng Huang ◽  
Huajiang Ouyang ◽  
Hongli Gao ◽  
Liang Guo ◽  
Dan Li ◽  
...  
Keyword(s):  
Feature Extraction ◽  
Extraction Method ◽  
Signal To Noise Ratio ◽  
Experimental Studies ◽  
Vibration Signal ◽  
Noise Sources ◽  
Rolling Bearings ◽  
Vibration Signals ◽  
Feature Extraction Method ◽  
Spectral Kurtosis

Abstract Detection of incipient degradation demands extracting sensitive features accurately when signal-to-noise ratio (SNR) is very poor, which appears in most industrial environments. Vibration signals of rolling bearings are widely used for bearing fault diagnosis. In this paper, we propose a feature extraction method that combines Blind Source Separation (BSS) and Spectral Kurtosis (SK) to separate independent noise sources. Normal, and incipient fault signals from vibration tests of rolling bearings are processed. We studied 16 groups of vibration signals (which all display an increase in kurtosis) of incipient degradation after they are processed by a BSS filter. Compared with conventional kurtosis, theoretical studies of SK trends show that the SK levels vary with frequencies and some experimental studies show that SK trends of measured vibration signals of bearings vary with the amount and level of impulses in both vibration and noise signals due to bearing faults. It is found that the peak values of SK increase when vibration signals of incipient faults are processed by a BSS filter. This pre-processing by a BSS filter makes SK more sensitive to impulses caused by performance degradation of bearings.

Feature Extraction of Rolling Bearing Based on LMD Energy Feature

2017 ◽  
Vol 868 ◽  
pp. 363-368
Author(s):  
Bang Sheng Xing ◽  
Le Xu
Keyword(s):  
Feature Extraction ◽  
Vibration Signal ◽  
Rolling Bearing ◽  
Small Samples ◽  
Rolling Bearings ◽  
Vibration Signals ◽  
Feature Extraction Method ◽  
Fault Features ◽  
Local Mean ◽  
Energy Feature

For the situation that it is difficult to diagnose rolling bearings fault effectively for small samples, so it proposes a feature extraction method of rolling bearing based on local mean decomposition (LMD) energy feature. Due to the frequency domain distribution of vibration signals will change when different faults occur in rolling bearings, so it can use LMD energy feature method to extract the fault features of rolling bearings. The instances analysis and extracted results show that the LMD energy feature can extract the vibration signal fault feature of rolling bearings effectively.

scholarly journals A Novel Feature Extraction Method for Power Transformer Vibration Signal Based on CEEMDAN and Multi-Scale Dispersion Entropy

Entropy ◽  
2021 ◽  
Vol 23 (10) ◽  
pp. 1319
Author(s):  
Haikun Shang ◽  
Junyan Xu ◽  
Yucai Li ◽  
Wei Lin ◽  
Jinjuan Wang
Keyword(s):  
Feature Extraction ◽  
Fault Diagnosis ◽  
Extraction Method ◽  
Vibration Signal ◽  
Practical Significance ◽  
Stable Operation ◽  
Intrinsic Mode Functions ◽  
Vibration Signals ◽  
Feature Extraction Method ◽  
Multi Scale

Effective diagnosis of vibration fault is of practical significance to ensure the safe and stable operation of power transformers. Aiming at the traditional problems of transformer vibration fault diagnosis, a novel feature extraction method based on complete ensemble empirical mode decomposition with adaptive noise (CEEMDAN) and multi-scale dispersion entropy (MDE) was proposed. In this paper, CEEMDAN method is used to decompose the original transformer vibration signal. Additionally, then MDE is used to capture multi-scale fault features in the decomposed intrinsic mode functions (IMFs). Next, the principal component analysis (PCA) method is employed to reduce the feature dimension and extract the effective information in vibration signals. Finally, the simplified features are sent into density peak clustering (DPC) to get the fault diagnosis results. The experimental data analysis shows that CEEMDAN-MDE can effectively extract the information of the original vibration signals and DPC can accurately diagnose the types of transformer faults. By comparing different algorithms, the practicability and superiority of this proposed method are verified.

scholarly journals Multistage Fault Feature Extraction of Consistent Optimization for Rolling Bearings Based on Correlated Kurtosis

2020 ◽  
Vol 2020 ◽  
pp. 1-16
Author(s):  
Long Zhang ◽  
Binghuan Cai ◽  
Guoliang Xiong ◽  
Jianmin Zhou ◽  
Wenbin Tu ◽  
...  
Keyword(s):  
Feature Extraction ◽  
Fault Diagnosis ◽  
Vibration Signal ◽  
Diagnostic Methods ◽  
Rolling Bearings ◽  
Feature Extraction Method ◽  
Transmission Path ◽  
The Individual ◽  
Envelope Spectrum ◽  
Fault Feature Extraction

Fault diagnosis of rolling bearings is not a trivial task because fault-induced periodic transient impulses are always submerged in environmental noise as well as large accidental impulses and attenuated by transmission path. In most hybrid diagnostic methods available for rolling bearings, the problems lie in twofolds. First, most optimization indices used in the individual signal processing stage do not take the periodical characteristic of fault transient impulses into consideration. Second, the individual stages make use of different optimization indices resulting in inconsistent optimization directions and possibly an unsatisfied diagnosis. To solve these problems, a multistage fault feature extraction method of consistent optimization for rolling bearings based on correlated kurtosis (CK) is proposed where maximum correlated kurtosis deconvolution (MCKD) is employed to attenuate the influence of transmission path followed by tunable Q factor wavelet transform (TQWT) to further enhance fault features by decomposing the preprocessed signals into multiple subbands under different Q values. The major contribution of the proposed approach is to consistently use CK as an optimization index of both MCKD and TQWT. The subband signal with the maximum CK which is an index being able to measure the periodical transient impulses in vibration signal yields an envelope spectrum, from which fault diagnosis is implemented. Simulated and experimental signals verified the effectiveness and advantages of the proposed method.

Feature Extraction Method for Rolling Bearing’s Week Fault Based on Kalman Filter and FSK

2014 ◽  
Vol 574 ◽  
pp. 684-689
Author(s):  
Zhi Chuan Liu ◽  
Li Wei Tang ◽  
Li Jun Cao
Keyword(s):  
Feature Extraction ◽  
Kalman Filter ◽  
Extraction Method ◽  
Model Parameters ◽  
Band Pass Filter ◽  
Pass Filter ◽  
Feature Extraction Method ◽  
Spectral Kurtosis ◽  
Band Pass ◽  
Fault Feature Extraction

Aiming at the problem that traditional demodulated resonance technology has the deficiency of difficulty to choose the parameters of band-pass filter, Kalman filter technology and fast spectral kurtosis were combined for fault feature extraction of rolling bearing. AR model was firstly built with gearbox original vibration signals, and then model order was ascertained with AIC formula, and finally model parameters were calculated with least-squares method. The original signals were pretreated by Kalman filter. Fast spectral kurtosis (FSK) was used to choose parameters of the best band-pass filter, and finally fault diagnosis was achieved by the energy operator demodulation spectrum analysis of band-pass filtered signal. The analysis result of engineering signals indicated that fault feature extraction method based on Kalman filter and fast spectral kurtosis can primely provide a new feature extraction method for rolling bearing’s week fault.

Tool Breakage Feature Extraction in PCB Micro-Hole Drilling Using Vibration Signals

2012 ◽  
Vol 497 ◽  
pp. 126-131 ◽  
Author(s):  
Zhen Hua Ren ◽  
Xiao Hu Zheng ◽  
Qing Long An ◽  
Cheng Yong Wang ◽  
Ming Chen
Keyword(s):  
Feature Extraction ◽  
Printed Circuit Board ◽  
Vibration Signal ◽  
Circuit Board ◽  
Hole Drilling ◽  
Features Selection ◽  
Tool Breakage ◽  
Vibration Signals ◽  
Feature Extraction Method ◽  
Micro Hole

Tool breakage monitoring is crucial to automation fabrication, especially for high-density hole machining, such as PCB (Printed Circuit Board). A tool breakage feature extraction method in PCB micro-hole drilling is presented in this paper. The vibration signal is analyzed by wavelet transform. The decomposed signals energy ratio at each frequency band is computed as monitoring features. The monitoring performance of different features selection is given. The vibration signals are observed to provide the capability in distinguishing micro drill breakage with proper features extraction and classifier design.

A Fault Feature Extraction Method Based on LMD and MSE for Reciprocating Compressor

2014 ◽  
Vol 530-531 ◽  
pp. 345-348
Author(s):  
Min Qiang Xu ◽  
Hai Yang Zhao ◽  
Jin Dong Wang
Keyword(s):  
Feature Extraction ◽  
Extraction Method ◽  
Vibration Signal ◽  
Multiscale Entropy ◽  
Reciprocating Compressor ◽  
Feature Extraction Method ◽  
Feature Vectors ◽  
Euclidean Distances ◽  
Coupling Characteristics ◽  
Fault Feature Extraction

This paper presents a feature extraction method based on LMD and MSE for reciprocating compressor according to the strong nonstationarity, nonlinearity and features coupling characteristics of vibration signal. The vibration signal was decomposed into a set of PFs, and then multiscale entropy of the first several PFs were calculated as feature vectors with different scale factors. Based on the maximum of average Euclidean distances, the feature vectors which have the best divisibility were selected. The feature vectors of reciprocating compressor at different bearing clearance states were extracted using this method, and superiority of this method is verified by comparing with the results of sample entropy.

scholarly journals A Vibration Feature Extraction Method Based on Time-Domain Dimensional Parameters and Mahalanobis Distance

2021 ◽  
Vol 2021 ◽  
pp. 1-12
Author(s):  
Junjun Chen ◽  
Bing Xu ◽  
Xin Zhang
Keyword(s):  
Feature Extraction ◽  
Frequency Domain ◽  
Time Domain ◽  
Mahalanobis Distance ◽  
Extraction Method ◽  
Vibration Signal ◽  
Feature Extraction Method ◽  
Feature Parameters ◽  
Dimensional Parameters ◽  
Failure Types

To accurately describe the characteristics of a signal, the feature parameters in time domain and frequency domain are usually extracted for characterization. However, the total number of feature parameters in time domain and frequency domain exceeds twenty, and all of the feature parameters are used for feature extraction, which will result in a large amount of data processing. For the purpose of using fewer feature parameters to accurately reflect the characteristics of the vibration signal, a simple but effective vibration feature extraction method combining time-domain dimensional parameters (TDDP) and Mahalanobis distance (MD) is proposed, i.e., TDDP-MD. In this method, ten time-domain dimensional parameters are selected to extract fault features, and the distance evaluation technique based on Mahalanobis distance criterion function is also introduced to calculate the feature vector, which can be used to classify different failure types. Finally, the proposed method is applied to fault diagnosis of rolling element bearings, and experimental analysis results show that the proposed method can recognize different failure types accurately and effectively with only ten time-domain dimensional parameters and a small quantity of training samples.

Sign in / Sign up

Export Citation Format

Share Document