scholarly journals Preparation and Characterization of Silk Fibroin Nanoparticles as a Potential Drug Delivery System for 5-Fluorouracil

2019 ◽  
Vol 9 (4) ◽  
pp. 601-608 ◽  
Author(s):  
Hamid Rahmani ◽  
Ali Fattahi ◽  
Komail Sadrjavadi ◽  
Salar Khaledian ◽  
Yalda Shokoohinia
Keyword(s):  
Electron Microscope ◽  
Controlled Release ◽  
Silk Fibroin ◽  
Delivery System ◽  
In Vitro Release ◽  
Xrd Analysis ◽  
Loading Efficiency ◽  
Silk Fibroin Nanoparticles ◽  
Ft Ir

Purpose: The aim of this study is to prepare 5-fluorouracil (5-FU) loaded silk fibroin nanoparticles(SFNPs) and to achieve a controlled release delivery system with the high loading capacity. Methods: SFNPs with 1:1, 1:3, and 1:10 ratios of 5-FU to silk fibroin were prepared. SFNPswere characterized by Fourier-transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD)analysis, Scanning electron microscope (SEM), and Transmission electron microscope (TEM).Loading efficiency, in vitro release, and cell viability were studied for optimal SFNPs. Results: The ratio of 1:1 was optimal formulation with the size and polydispersity index (PDI)of 221.03 nm and 0.093 before freeze drying, and 286.7 nm and 0.154 after freeze dryingby lactose, respectively. The loading efficiency and loading content of this ratio were 52.32%and 34.35%, respectively. FT-IR and XRD analysis indicated the conformational change (fromrandom coil to β-sheet) in the structure of nanoparticles by increasing amount of the drug, whichcaused the smaller size, the higher loading efficiency, and the slower release pattern. The drugloadednanoparticles reached to the half maximal inhibitory concentration (IC50) that werecomparable with free drug on MCF7 (human breast cancer) cell line. Conclusion: This study was planned to achieve a promising controlled release drug deliverysystem for carrying 5-FU, as a potent anticancer drug. SFNPs were found proper candidates fordelivery of a hydrophilic drug such as 5-FU.

scholarly journals Topical Chitosan-Based Thermo-Responsive Scaffold Provides Dexketoprofen Trometamol Controlled Release for 24 h Use

Pharmaceutics ◽  
2021 ◽  
Vol 13 (12) ◽  
pp. 2100
Author(s):  
Luis Castillo-Henríquez ◽  
Pablo Sanabria-Espinoza ◽  
Brayan Murillo-Castillo ◽  
Gabriela Montes de Oca-Vásquez ◽  
Diego Batista-Menezes ◽  
...  
Keyword(s):  
Controlled Release ◽  
Kinetic Models ◽  
In Vitro Release ◽  
Solution Temperature ◽  
Burst Release ◽  
Release Studies ◽  
Dexketoprofen Trometamol ◽  
Ft Ir ◽  
Healing Wounds

Chronic and non-healing wounds demand personalized and more effective therapies for treating complications and improving patient compliance. Concerning that, this work aims to develop a suitable chitosan-based thermo-responsive scaffold to provide 24 h controlled release of Dexketoprofen trometamol (DKT). Three formulation prototypes were developed using chitosan (F1), 2:1 chitosan: PVA (F2), and 1:1 chitosan:gelatin (F3). Compatibility tests were done by DSC, TG, and FT-IR. SEM was employed to examine the morphology of the surface and inner layers from the scaffolds. In vitro release studies were performed at 32 °C and 38 °C, and the profiles were later adjusted to different kinetic models for the best formulation. F3 showed the most controlled release of DKT at 32 °C for 24 h (77.75 ± 2.72%) and reduced the burst release in the initial 6 h (40.18 ± 1.00%). The formulation exhibited a lower critical solution temperature (LCST) at 34.96 °C, and due to this phase transition, an increased release was observed at 38 °C (88.52 ± 2.07% at 12 h). The release profile for this formulation fits with Hixson–Crowell and Korsmeyer–Peppas kinetic models at both temperatures. Therefore, the developed scaffold for DKT delivery performs adequate controlled release, thereby; it can potentially overcome adherence issues and complications in wound healing applications.

scholarly journals Fabrication of Bio-Nanocomposite Based on HNT-Methionine for Controlled Release of Phenytoin

Polymers ◽  
2021 ◽  
Vol 13 (15) ◽  
pp. 2576
Author(s):  
Majid Abdouss ◽  
Nastaran Radgoudarzi ◽  
Alireza Mohebali ◽  
Elaheh Kowsari ◽  
Mojtaba Koosha ◽  
...  
Keyword(s):  
Controlled Release ◽  
Zeta Potential ◽  
Encapsulation Efficiency ◽  
Release Profile ◽  
Burst Release ◽  
Loading Efficiency ◽  
Phenytoin Sodium ◽  
Good Potential ◽  
Ft Ir

In this study, a novel promising approach for the fabrication of Halloysite nanotube (HNT) nanocomposites, based on the amino acid named Methionine (Met), was investigated. For this purpose, Met layered on the outer silane functionalized surface of HNT for controlled release of Phenytoin sodium (PHT). The resulting nanocomposite (MNT-g-Met) was characterized by FTIR, XRD, Zeta potential, TGA, TEM and FE-SEM. The FT-IR results showed APTES and Met peaks, which proved the modification of the HNTs. The zeta-potential results showed the interaction between APTES (+53.30) and Met (+38.80) on the HNTs (−30.92). The FE-SEM micrographs have displayed the grafting of Met on the modified HNTs due to the nanotube conversion to a rough and indistinguishable form. The amount of encapsulation efficiency (EE) and loading efficiency (LE) of MNT-g-Met was 74.48% and 37.24%, while pure HNT was 57.5%, and 28.75%, respectively. In-vitro studies showed that HNT had a burst release (70% in 6 h) in phosphate buffer while MNT-g-Met has more controlled release profile (30.05 in 6 h) and it was found to be fitted with the Korsmeyer-Peppas model. Due to the loading efficiency and controlled release profile, the nanocomposite promote a good potential for drug delivery of PHT.

Bosentan Monohydrate Vesicles Loaded Transdermal Drug Delivery System: In Vitro In Vivo Evaluation

2017 ◽  
Vol 7 (1) ◽  
Author(s):  
Revathi M. ◽  
Indira Y.
Keyword(s):  
Controlled Release ◽  
Delivery System ◽  
Ex Vivo ◽  
In Vitro Release ◽  
In Vivo Studies ◽  
In Vivo Evaluation ◽  
Vitro Release ◽  
Transdermal Route

This study elucidates the enhancement of the permeation of bosentan monohydrate through skin by encapsulating it in vesicles loaded transdermal delivery system. Niosomal vesicles were formulated by ether injection method. Formulation FN7 (span 60: cholesterol: poloxamer 401, 1.25:1:0.25) showed maximum entrapment efficiency of 96.7±0.037% and was optimized for loading in to transdermal system. Transdermal systems were formulated using both hydrophilic and hydrophobic polymers like HPMC, HEC and EC. Formulation F1 with HPMC was optimized based on in vitro release (99.21±1.45 %) and was further evaluated for ex-vivo permeation. The results indicate that the ex vivo release (98.13±1.65%) was as par with in vitro release and followed zero order super case- II transport mechanism. The in vivo studies were done on New Zealand male rabbits for oral and transdermal route. The results inferred no significant change in half-life of drug but a substantial difference in Tmax, AUC and MRT was observed in transdermal systems. A two fold increase in AUC was observed in transdermal route (18.609±7.251µg/ml/h) when compared to oral route (9.644±5.621µg/ml/h). A controlled release was attained up to 35h and reservoir effect was observed and this may be due to the barrier properties of skin. Drug encapsulated niosomes were released in to the skin by loosening the lipid layers and the surfactant acted as penetration enhancer. The study infers that niosomes loaded transdermal patches of bosentan monohydrate can enhance the bioavailability and provided controlled release for better therapeutic efficacy and safety of drug.

Controlled Release of Metformin Hydrochloride I. In vitro Release from Physical Mixture Containing Xanthan Gum as Hydrophilic Rate Retarding Polymer

1970 ◽  
Vol 4 (1) ◽  
Author(s):  
Mashkura Ashrafi ◽  
Jakir Ahmed Chowdhury ◽  
Md Selim Reza
Keyword(s):  
Controlled Release ◽  
Xanthan Gum ◽  
In Vitro Release ◽  
Correlation Coefficients ◽  
High Ratio ◽  
Water Soluble ◽  
Metformin Hydrochloride ◽  
Model Drug ◽  
Very High

Capsules of different formulations were prepared by using a hydrophilic polymer, xanthan gum and a filler Ludipress. Metformin hydrochloride, which is an anti-diabetic agent, was used as a model drug here with the aim to formulate sustained release capsules. In the first 6 formulations, metformin hydrochloride and xanthan gum were used in different ratio. Later, Ludipress was added to the formulations in a percentage of 8% to 41%. The total procedure was carried out by physical mixing of the ingredients and filling in capsule shells of size ‘1’. As metformin hydrochloride is a highly water soluble drug, the dissolution test was done in 250 ml distilled water in a thermal shaker (Memmert) with a shaking speed of 50 rpm at 370C &plusmn 0.50C for 6 hours. After the dissolution, the data were treated with different kinetic models. The results found from the graphs and data show that the formulations follow the Higuchian release pattern as they showed correlation coefficients greater than 0.99 and the sustaining effect of the formulations was very high when the xanthan gum was used in a very high ratio with the drug. It was also investigated that the Ludipress extended the sustaining effect of the formulation to some extent. But after a certain period, Ludipress did not show any significant effect as the pores made by the xanthan gum network were already blocked. It is found here that when the metformin hydrochloride and the xanthan gum ratio was 1:1, showed a high percentage of drug release, i.e. 91.80% of drug was released after 6 hours. But With a xanthan gum and metformin hydrochloride ratio of 6:1, a very slow release of the drug was obtained. Only 66.68% of the drug was released after 6 hours. The percent loading in this case was 14%. Again, when Ludipress was used in high ratio, it was found to retard the release rate more prominently. Key words: Metformin Hydrochloride, Xanthan Gum, Controlled release capsule Dhaka Univ. J. Pharm. Sci. Vol.4(1) 2005 The full text is of this article is available at the Dhaka Univ. J. Pharm. Sci. website

Solubility Enhancement of Poorly Water-Soluble Antifungal Drug Acyclovir by Nanocrystal Formulation Approach

2018 ◽  
Vol 11 (2) ◽  
pp. 4036-4042
Author(s):  
Prakash Goudanavar ◽  
Ankit Acharya ◽  
Vinay C.H
Keyword(s):  
Chemical Interaction ◽  
Research Work ◽  
Antiviral Drug ◽  
In Vitro Release ◽  
Oral Route ◽  
Water Soluble ◽  
Precipitation Method ◽  
Dsc Studies ◽  
Ft Ir

Administration of an antiviral drug, acyclovir via the oral route leads to low and variable bioavailability (15-30%). Therefore, this research work was aimed to enhance bioavailability of acyclovir by nanocrystallization technique. The drug nanocrystals were prepared by anti-solvent precipitation method in which different stabilizers were used. The formed nanocrystals are subjected to biopharmaceutical characterization including solubility, particle size and in-vitro release. SEM studies showed nano-crystals were crystalline nature with sharp peaks. The formulated drug nanocrystals were found to be in the range of 600-900nm and formulations NC7 and NC8 showed marked improvement in dissolution velocity when compared to pure drug, thus providing greater bioavailability. FT-IR and DSC studies revealed the absence of any chemical interaction between drug and polymers used. 

A study on using expanded perlite with hydroxyapatite: Reinforced bio-composites

2021 ◽  
pp. 095441192199656
Author(s):  
Erdoğan Karip ◽  
Mehtap Muratoğlu
Keyword(s):  
Body Fluid ◽  
Xrd Analysis ◽  
Cold Isostatic Pressing ◽  
Expanded Perlite ◽  
X Ray Diffraction ◽  
Pressing Method ◽  
X Ray ◽  
Infra Red ◽  
Ft Ir

People are exposed to different kinds of diseases or various accidents in life. Hydroxyapatite (HA) has been widely employed for bone treatment applications. In this study, HA was extracted from sheep bones. Bio-composites were doped with 1, 5, and 10 wt.% of expanded perlite and 5 wt.% of ZrO2–MgO-P2O5. The bio-composites were prepared by the cold isostatic pressing method (250 MPa) and sintered at 900°C for 1 h. In order to evaluate the characteristics of the bio-composites, microhardness, density, X-ray diffraction (XRD), Fourier transform infra-red spectroscopy (FT-IR), scanning electron microscopy (SEM), and energy dispersive spectroscopy (EDS) analyses were carried out on them. Additionally, the specimens whose characteristics were determined were kept in synthetic body fluid (SBF), and their in vitro behavior was examined. As a result, it was observed that microhardness increased as both the weight and the grain size of the expanded perlite were increased. Calcium silicate, tri-calcium phosphate, and hydroxyapatite were observed in the XRD analysis of all samples, and the formation of apatite structures was increased by addition of ZrO2–MgO–P2O5.

scholarly journals Design and In Vitro Study of a Dual Drug-Loaded Delivery System Produced by Electrospinning for the Treatment of Acute Injuries of the Central Nervous System

Pharmaceutics ◽  
2021 ◽  
Vol 13 (6) ◽  
pp. 848
Author(s):  
Luisa Stella Dolci ◽  
Rosaria Carmela Perone ◽  
Roberto Di Gesù ◽  
Mallesh Kurakula ◽  
Chiara Gualandi ◽  
...  
Keyword(s):  
Central Nervous System ◽  
Nervous System ◽  
Delivery System ◽  
Synergistic Effects ◽  
In Vitro Release ◽  
Health Priorities ◽  
The Central Nervous System ◽  
Vitro Release ◽  
Dual Drug

Vascular and traumatic injuries of the central nervous system are recognized as global health priorities. A polypharmacology approach that is able to simultaneously target several injury factors by the combination of agents having synergistic effects appears to be promising. Herein, we designed a polymeric delivery system loaded with two drugs, ibuprofen (Ibu) and thyroid hormone triiodothyronine (T3) to in vitro release the suitable amount of the anti-inflammation and the remyelination drug. As a production method, electrospinning technology was used. First, Ibu-loaded micro (diameter circa 0.95–1.20 µm) and nano (diameter circa 0.70 µm) fibers were produced using poly(l-lactide) PLLA and PLGA with different lactide/glycolide ratios (50:50, 75:25, and 85:15) to select the most suitable polymer and fiber diameter. Based on the in vitro release results and in-house knowledge, PLLA nanofibers (mean diameter = 580 ± 120 nm) loaded with both Ibu and T3 were then successfully produced by a co-axial electrospinning technique. The in vitro release studies demonstrated that the final Ibu/T3 PLLA system extended the release of both drugs for 14 days, providing the target sustained release. Finally, studies in cell cultures (RAW macrophages and neural stem cell-derived oligodendrocyte precursor cells—OPCs) demonstrated the anti-inflammatory and promyelinating efficacy of the dual drug-loaded delivery platform.

scholarly journals Formulation and development of metformin-loaded microspheres using Khaya senegalensis (Meliaceae) gum as co-polymer

2020 ◽  
Vol 6 (1) ◽  
Author(s):  
Chukwuebuka H. Ozoude ◽  
Chukwuemeka P. Azubuike ◽  
Modupe O. Ologunagba ◽  
Sejoro S. Tonuewa ◽  
Cecilia I. Igwilo
Keyword(s):  
Controlled Release ◽  
Sodium Alginate ◽  
Release Kinetics ◽  
Drug Carrier ◽  
In Vitro Release ◽  
Entrapment Efficiency ◽  
Metformin Hydrochloride ◽  
Scanning Calorimetry ◽  
Khaya Senegalensis

Abstract Background Khaya gum is a bark exudate from Khaya senegalensis (Maliaecae) that has drug carrier potential. This study aimed to formulate and comparatively evaluate metformin-loaded microspheres using blends of khaya gum and sodium alginate. Khaya gum was extracted and subjected to preformulation studies using established protocols while three formulations (FA; FB and FC) of metformin (1% w/v)-loaded microspheres were prepared by the ionic gelation method using 5% zinc chloride solution as the cross-linker. The formulations contained 2% w/v blends of khaya gum and sodium alginate in the ratios of 2:3, 9:11, and 1:1, respectively. The microspheres were evaluated by scanning electron microscopy, Fourier transform-infrared spectroscopy, differential scanning calorimetry, entrapment efficiency, swelling index, and in vitro release studies. Results Yield of 28.48%, pH of 4.00 ± 0.05, moisture content (14.59% ± 0.50), and fair flow properties (Carr’s index 23.68 ± 1.91 and Hausner’s ratio 1.31 ± 0.03) of the khaya gum were obtained. FTIR analyses showed no significant interaction between pure metformin hydrochloride with excipients. Discrete spherical microspheres with sizes ranging from 1200 to 1420 μm were obtained. Drug entrapment efficiency of the microspheres ranged from 65.6 to 81.5%. The release of the drug from microspheres was sustained for the 9 h of the study as the cumulative release was 62% (FA), 73% (FB), and 80% (FC). The release kinetics followed Korsmeyer-Peppas model with super case-II transport mechanism. Conclusion Blends of Khaya senegalensis gum and sodium alginate are promising polymer combination for the preparation of controlled-release formulations. The blend of the khaya gum and sodium alginate produced microspheres with controlled release properties. However, the formulation containing 2:3 ratio of khaya gum and sodium alginate respectively produced microspheres with comparable controlled release profiles to the commercial brand metformin tablet.

Montmorillonite-Alginate Nanocomposites as a Drug Delivery System: Intercalation and In Vitro Release of Vitamin B1 and Vitamin B6

2009 ◽  
Vol 25 (2) ◽  
pp. 161-177 ◽  
Author(s):  
Bhavesh D. Kevadiya ◽  
Ghanshyam V. Joshi ◽  
Hasmukh A. Patel ◽  
Pravin G. Ingole ◽  
Haresh M. Mody ◽  
...  
Keyword(s):  
Drug Delivery ◽  
Drug Delivery System ◽  
Delivery System ◽  
Vitamin B6 ◽  
In Vitro Release ◽  
Vitamin B1 ◽  
Vitro Release
Sign in / Sign up

Export Citation Format

Share Document