An Examination of Compressive Strength Variation of Pozzolan-Lime Cement with Pozzolan Particle Size

2015 ◽  
Keyword(s):  
Particle Size ◽  
Compressive Strength ◽  
Strength Variation

scholarly journals Experimental Analysis of the Mechanical Properties and Resistivity of Tectonic Coal Samples with Different Particle Sizes

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2303
Author(s):  
Congyu Zhong ◽  
Liwen Cao ◽  
Jishi Geng ◽  
Zhihao Jiang ◽  
Shuai Zhang
Keyword(s):  
Mechanical Properties ◽  
Particle Size ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Uniaxial Compressive Strength ◽  
Coalbed Methane ◽  
Coal Sample ◽  
Fine Particles ◽  
Particle Sizes ◽  
Tectonic Coal

Because of its weak cementation and abundant pores and cracks, it is difficult to obtain suitable samples of tectonic coal to test its mechanical properties. Therefore, the research and development of coalbed methane drilling and mining technology are restricted. In this study, tectonic coal samples are remodeled with different particle sizes to test the mechanical parameters and loading resistivity. The research results show that the particle size and gradation of tectonic coal significantly impact its uniaxial compressive strength and elastic modulus and affect changes in resistivity. As the converted particle size increases, the uniaxial compressive strength and elastic modulus decrease first and then tend to remain unchanged. The strength of the single-particle gradation coal sample decreases from 0.867 to 0.433 MPa and the elastic modulus decreases from 59.28 to 41.63 MPa with increasing particle size. The change in resistivity of the coal sample increases with increasing particle size, and the degree of resistivity variation decreases during the coal sample failure stage. In composite-particle gradation, the proportion of fine particles in the tectonic coal sample increases from 33% to 80%. Its strength and elastic modulus increase from 0.996 to 1.31 MPa and 83.96 to 125.4 MPa, respectively, and the resistivity change degree decreases. The proportion of medium particles or coarse particles increases, and the sample strength, elastic modulus, and resistivity changes all decrease.

scholarly journals Grinding Kinetics of Slag and Effect of Final Particle Size on the Compressive Strength of Alkali Activated Materials

Minerals ◽  
2019 ◽  
Vol 9 (11) ◽  
pp. 714 ◽  
Author(s):  
Evangelos Petrakis ◽  
Vasiliki Karmali ◽  
Georgios Bartzas ◽  
Konstantinos Komnitsas
Keyword(s):  
Particle Size ◽  
Compressive Strength ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
Ageing Time ◽  
Reduction Rate ◽  
Curing Temperature ◽  
Alkali Activation ◽  
Final Particle ◽  
Alkali Activated

This study aims to model grinding of a Polish ferronickel slag and evaluate the particle size distributions (PSDs) of the products obtained after different grinding times. Then, selected products were alkali activated in order to investigate the effect of particle size on the compressive strength of the produced alkali activated materials (AAMs). Other parameters affecting alkali activation, i.e., temperature, curing, and ageing time were also examined. Among the different mathematical models used to simulate the particle size distribution, Rosin–Rammler (RR) was found to be the most suitable. When piecewise regression analysis was applied to experimental data it was found that the particle size distribution of the slag products exhibits multifractal character. In addition, grinding of slag exhibits non-first-order behavior and the reduction rate of each size is time dependent. The grinding rate and consequently the grinding efficiency increases when the particle size increases, but drops sharply near zero after prolonged grinding periods. Regarding alkali activation, it is deduced that among the parameters studied, particle size (and the respective specific surface area) of the raw slag product and curing temperature have the most noticeable impact on the compressive strength of the produced AAMs.

scholarly journals Phase evolution, characterisation, and performance of cement prepared in an oxy-fuel atmosphere

2016 ◽  
Vol 192 ◽  
pp. 113-124 ◽  
Author(s):  
Liya Zheng ◽  
Thomas P. Hills ◽  
Paul Fennell
Keyword(s):  
Particle Size ◽  
Compressive Strength ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
Carbon Capture ◽  
Raw Materials ◽  
Carbon Capture And Storage ◽  
Phase Evolution ◽  
Chemical Compositions ◽  
Phase And Elemental Compositions

Cement manufacture is one of the major contributors (7–10%) to global anthropogenic CO2 emissions. Carbon capture and storage (CCS) has been identified as a vital technology for decarbonising the sector. Oxy-fuel combustion, involving burning fuel in a mixture of recycled CO2 and pure O2 instead of air, makes CO2 capture much easier. Since it combines a theoretically lower energy penalty with an increase in production, it is attractive as a CCS technology in cement plants. However, it is necessary to demonstrate that changes in the clinkering atmosphere do not reduce the quality of the clinker produced. Clinkers were successfully produced in an oxy-fuel atmosphere using only pure oxides as raw materials as well as a mixture of oxides and clay. Then, CEM I cements were prepared by the addition of 5 wt% gypsum to the clinkers. Quantitative XRD and XRF were used to obtain the phase and elemental compositions of the clinkers. The particle size distribution and compressive strength of the cements at 3, 7, 14, and 28 days' ages were tested, and the effect of the particle size distribution on the compressive strength was investigated. Additionally, the compressive strength of the cements produced in oxy-fuel atmospheres was compared with those of the cement produced in air and commercially available CEMEX CEM I. The results show that good-quality cement can be successfully produced in an oxy-fuel atmosphere and it has similar phase and chemical compositions to CEM I. Additionally, it has a comparable compressive strength to the cement produced in air and to commercially available CEMEX CEM I.

Ultra-Durable Concretes: Structure at the Micro- and Nanoscale

MRS Bulletin ◽  
2004 ◽  
Vol 29 (5) ◽  
pp. 324-327 ◽  
Author(s):  
Christian P. Vernet
Keyword(s):  
Particle Size ◽  
Compressive Strength ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
Carrying Capacity ◽  
Load Carrying Capacity ◽  
Fiber Reinforced ◽  
Remarkable Improvement ◽  
Load Carrying ◽  
Wide Particle Size Distribution

AbstractUltrahigh-performance concretes (UHPCs) are obtained by optimizing several technologies: minimizing the amount of water added, using superplasticizers and a wide particle size distribution, and packing the particles to improve fluidity with minimized water additions and to optimize load-carrying capacity. Fibers can be incorporated to increase ductility, leading to ultrahigh-performance fiber-reinforced concretes (UHPFRCs). Such enhanced concretes can approach the compressive strength of steel, with a remarkable improvement in durability. UHPCs offer new solutions for innovative construction, especially in aggressive environments.

scholarly journals Influence of Particle Size Distribution of High Calcium Fly Ash on HVFA Mortar Properties

2018 ◽  
Vol 20 (2) ◽  
pp. 51
Author(s):  
Antoni . ◽  
Hendra Surya Wibawa ◽  
Djwantoro Hardjito
Keyword(s):  
Particle Size ◽  
Compressive Strength ◽  
Fly Ash ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
Setting Time ◽  
High Volume ◽  
High Volume Fly Ash ◽  
High Calcium ◽  
High Calcium Fly Ash

This study evaluates the effect of particle size distribution (PSD) of high calcium fly ash on high volume fly ash (HVFA) mortar characteristics. Four PSD variations of high calcium fly ash used were: unclassified fly ash and fly ash passing sieve No. 200, No. 325 and No. 400, respectively. The fly ash replacement ratio of the cementitious material ranged between 50-70%. The results show that with smaller fly ash particles size and higher levels of fly ash replacement, the workability of the mixture was increased with longer setting time. There was an increase in mortar compressive strength with finer fly ash particle size, compared to those with unclassified ones, with the highest strength was found at those with fly ash passing mesh No. 325. The increase was found due to better compactability of the mixture. Higher fly ash replacement reduced the mortar’s compressive strength, however, the rate was reduced when finer fly ash particles was used.

Characteristics of High Content Steel Briquettes Using Nanosized Solid Binders

2021 ◽  
Vol 21 (7) ◽  
pp. 3863-3867
Author(s):  
Seung-Ju Lim ◽  
Seong-Gyu Seo ◽  
Hyung-Sun Yoon
Keyword(s):  
Particle Size ◽  
Compressive Strength ◽  
Average Particle Size ◽  
Average Particle ◽  
Eds Analysis

In this study, we investigated the characteristics of high-content steel briquettes produced using various nanoscale solid binders and steel byproducts (SS, SCS, SLD, and BSD). The average particle size was 0.171 nm for S5, 0.065 nm for S1, 0.058 nm for S4, and 0.040 nm for S2 and S3. The SEM-EDS analysis of the solid power binder resulted in mostly rectangular images. The compressive strength of the high-content steel briquettes was 120 kgf/cm2, with the highest HSL1 using S4 binders. The compressive strength of the high-content steel briquettes was in the order of HSS4 > HSS1 > HSS3 > HSS5 > HSS2.

scholarly journals Effect of Slag Particle Size on Fracture Toughness of Concrete

2019 ◽  
Vol 9 (4) ◽  
pp. 805 ◽  
Author(s):  
Chung-Ho Huang ◽  
Chung-Hao Wu ◽  
Shu-Ken Lin ◽  
Tsong Yen
Keyword(s):  
Fracture Toughness ◽  
Particle Size ◽  
Compressive Strength ◽  
Stress Intensity ◽  
Fracture Energy ◽  
Critical Stress ◽  
Critical Stress Intensity Factor ◽  
Cementitious Material ◽  
Test Results ◽  
Unique Effect

The effects of particle size of ground granulated blast furnace slag (GGBS) on the fracture energy, critical stress intensity, and strength of concrete are experimentally studied. Three fineness levels of GGBS of 4000, 5000, 6000 cm2/g were used. In addition to the control mixture without slag, two slag replacement levels of 20% and 40% by weight of the cementitious material were selected for preparing the concrete mixtures. The control mixture was designed to have a target compressive strength at 28 days of 62 MPa, while the water to cementitious material ratio was selected as 0.35 for all mixtures. Test results indicate that using finer slag in concrete may improve the filling effect and the reactivity of slag, resulting in a larger strength enhancement. The compressive strength of slag concrete was found to increase in conjunction with the fineness level of the slag presented in the mixture. Use of finer slag presents a beneficial effect on the fracture energy (GF) of concrete, even at an early age, and attains a higher increment of GF at later age (56 days). This implicates that the finer slag can have a unique effect on the enhancement of the fracture resistance of concrete. The test results of the critical stress intensity factor (KSIC) of the slag concretes have a similar tendency as that of the fracture energy, indicating that the finer slag may present an increase in the fracture toughness of concrete.

Fine-Grained Concrete with Nanodispersed Silica Additive

2020 ◽  
Vol 992 ◽  
pp. 156-161
Author(s):  
N.P. Lukuttsova ◽  
E.G. Borovik ◽  
D.A. Pehenko
Keyword(s):  
Particle Size ◽  
Compressive Strength ◽  
Pore Diameter ◽  
Fine Grained ◽  
Silica Concentration ◽  
Calcium Hydrosilicates ◽  
Additive Particle ◽  
Nanodispersed Silica ◽  
Silica Additive ◽  
Number Of Particles

The effect of the modifying nanodispersed silica (NS) additive, obtained by the polycondensation method, on the properties of fine-grained concrete (FGC) is studied. It is revealed that the dependence of the NS-additive particle size on its age is extreme. The maximum number of particles of up to 100 nm in the additive is observed at the age of 10 days, and then their number decreases. However, it affects the FGC strength little even after 30 days of the additive storage. It is established that the NS-additive could be most effectively used with 0.23% of an active silica concentration and pH 4.1 in combination with S-3. At that, the porosity declines from 17.5 to 12.9% and the pore diameter diminishes from 3.171 to 0.689 μm. It leads to an increase in the compressive strength by 2 times and a decrease in water absorption by 1.6 times as compared to the control composition without additives. An increase in the frost resistance of the modified fine-grained concrete to F250 is recorded; it occurs due to a decrease in porosity at portlandite binding with amorphous silica additives into low-basic calcium hydrosilicates.

scholarly journals Evaluation of Strengths from Cement Hydration and Slag Reaction of Mortars Containing High Volume of Ground River Sand and GGBF Slag

2019 ◽  
Vol 2019 ◽  
pp. 1-12 ◽  
Author(s):  
Punnaman Norrarat ◽  
Weerachart Tangchirapat ◽  
Smith Songpiriyakij ◽  
Chai Jaturapitakkul
Keyword(s):  
Particle Size ◽  
Compressive Strength ◽  
Cement Hydration ◽  
High Volume ◽  
Inert Material ◽  
Early Age ◽  
Particle Sizes ◽  
River Sand ◽  
Reactive Material ◽  
Median Particle

This paper investigates the cement hydration, and the slag reaction contributes to the compressive strengths of mortars mixed with ground river sand (GRS) and ground-granulated blast furnace (GGBF) slag with different particle sizes. GRS (inert material) and GGBF slag (reactive material) were ground separately until the median particle sizes of 32 ± 1, 18 ± 1, and 5 ± 1 micron and used to replace Portland cement (PC) in large amount (40–60%) by weight of the binder. The results showed that, at the early age, the compressive strength obtained from the cement hydration was higher than that obtained from the slag reaction. The results of compressive strength also indicated that the GGBF slag content and particle size play important roles in the slag reaction at the later ages, whereas cement hydration is more prominent at the early ages. Although the results could be expected from the use of GGBF slag to replace PC in mortar or concrete, this study had presented the values of the compressive strength along with ages and the finenesses of GGBF slag that contributed from cement hydration and from GGBF slag reaction.

Sign in / Sign up

Export Citation Format

Share Document