scholarly journals Features of Machining Rotor Shafts of Diesel Engine Turbochargers with a Multilayer-Coated Tool

2021 ◽  
Vol 31 (4) ◽  
pp. 518-529
Author(s):  
Vladimir A. Skryabin
Keyword(s):  
Cutting Force ◽  
Experimental Studies ◽  
Titanium Carbonitride ◽  
Wear Resistant ◽  
Wear Resistant Coatings ◽  
Heat Resistant ◽  
Cutting Force Components ◽  
Alloy Steels ◽  
Force Components ◽  
Cutting Unit

Introduction. The paper presents the results of experimental studies of power parameters when hard alloy steels are machined with tools, the cutting units of which have multilayer hard, heat-resistant and wear-resistant coatings. The obtained data will make it possible to optimize machining hard-to-machine materials. Materials and Methods. The aim of the study is to measure the power parameters of turning products and to create experimental formulas of power parameters for different technological modes. For this purpose, a special measuring multicomponent complex was used to estimate the influence of the mode parameters on the change in the cutting force components. Results. The numerically controlled machine tool was retooled by combining it with a three-component dynamometer and tooling. The cutting unit of the tool was coated with a multi-layer hard, heat-resistant and wear-resistant coating. The tool was equipped with instruments connected to a personal computer for measuring and processing experimental data. According to the results of the study, there have been obtained graphical dependences and empirical formulas, which take into account the influence of the mode parameters on the cutting force components when machining the units of alloy steels of high hardness, heat resistance and wear resistance. Discussion and Conclusion.The study allowed us to obtain experimental formulas of cutting force components for different mode parameters when machining parts by the tool equipped with cutting plates. The plates are coated with multilayer hard and wear-resistant coatings of titanium carbonitride, aluminum oxide and nickel nitride. The coating increases significantly the hardness, heat and wears resistance of the tool cutting unit and provides quality machining.

scholarly journals The mathematical models for cutting force calculation during structural and corrosion-resistant steels` parts processing

2019 ◽  
Vol 298 ◽  
pp. 00099
Author(s):  
Alexey A. Zhdanov ◽  
Oleg A. Kursin ◽  
Pham Xuan Bach
Keyword(s):  
Mathematical Models ◽  
Cutting Force ◽  
Experimental Studies ◽  
Additional Parameter ◽  
Corrosion Resistant ◽  
Cutting Force Components ◽  
Force Components ◽  
Quantitative Indicators ◽  
Force Calculation ◽  
Thermo Physical Properties

The paper shows that conventional mathematical models for calculating the cutting force components during the turning process, represented in reference guides on engineering, give drastic errors reaching 100 percent or more for various tool-workpiece couples. These errors interfere with applying reference values of the cutting force for any further calculations, equipment selection, workpiece positioning scheme, workpiece deformation value due to the elastic of the technological system elements during processing and etc., because of the insufficient reliability of the results of such calculations. The paper proposes mathematical models obtained as a result of experimental studies, which allow for increasing the accuracy of the calculation of the components of the cutting force by introducing an additional parameter – i.e., the value of thermo EMF of the test running into the calculation formulas. This approach enables to reduce the error in the calculation of the components of the cutting force up to ± 15%. In addition, the need for the development of specific mathematical models for various groups of materials machined is shown, which is due to the peculiarities of contact processes in the machining of various groups of steels, as well as to qualitative and quantitative indicators of the thermo-physical properties of the materials of tool-workpiece contact couples.

Surface Roughness and Cutting Force Components Evaluation in Hard Turning by Differently Shaped Cutting Tools

2016 ◽  
Vol 862 ◽  
pp. 26-32 ◽  
Author(s):  
Michaela Samardžiová
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Hard Turning ◽  
Cutting Tool ◽  
Single Point ◽  
Machining Process ◽  
Tool Geometry ◽  
Machined Surface ◽  
Cutting Force Components ◽  
Force Components

There is a difference in machining by the cutting tool with defined geometry and undefined geometry. That is one of the reasons of implementation of hard turning into the machining process. In current manufacturing processes is hard turning many times used as a fine finish operation. It has many advantages – machining by single point cutting tool, high productivity, flexibility, ability to produce parts with complex shapes at one clamping. Very important is to solve machined surface quality. There is a possibility to use wiper geometry in hard turning process to achieve 3 – 4 times lower surface roughness values. Cutting parameters influence cutting process as well as cutting tool geometry. It is necessary to take into consideration cutting force components as well. Issue of the use of wiper geometry has been still insufficiently researched.

Artificial neural networks back propagation algorithm for cutting force components predictions

2013 ◽  
Vol 14 (6) ◽  
pp. 431-439 ◽  
Author(s):  
Issam Hanafi ◽  
Francisco Mata Cabrera ◽  
Abdellatif Khamlichi ◽  
Ignacio Garrido ◽  
José Tejero Manzanares
Keyword(s):  
Neural Networks ◽  
Artificial Neural Networks ◽  
Cutting Force ◽  
Back Propagation ◽  
Back Propagation Algorithm ◽  
Propagation Algorithm ◽  
Cutting Force Components ◽  
Artificial Neural ◽  
Force Components

scholarly journals Experiments in the Machining of Ice at Negative Rake Angles

1984 ◽  
Vol 30 (104) ◽  
pp. 77-81 ◽  
Author(s):  
D.K. Lieu ◽  
C.D. Mote
Keyword(s):  
Cutting Force ◽  
Chip Formation ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Rake Angle ◽  
Cutting Depth ◽  
Orthogonal Machining ◽  
Cutting Force Components ◽  
Force Components

AbstractThe cutting force components and the cutting moment on the cutting tool were measured during the orthogonal machining of ice with cutting tools inclined at negative rake angles. The variables included the cutting depth (< 1 mm), the cutting speed (0.01 ms−1to 1 ms−1), and the rake angles (–15° to –60°). Results of the experiments showed that the cutting force components were approximately independent of cutting speed. The resultant cutting force on the tool was in a direction approximately normal to the cutting face of the tool. The magnitude of the resultant force increased with the negative rake angle. Photographs of ice-chip formation revealed continuous and segmented chips at different cutting depths.

scholarly journals Modeling and Distribution Laws of Drilling Force for Staggered Teeth BTA Deep Hole Drill

2018 ◽  
Vol 2018 ◽  
pp. 1-13 ◽  
Author(s):  
Xubo Li ◽  
Jianming Zheng ◽  
Yan Li ◽  
Lingfei Kong ◽  
Weichao Shi ◽  
...  
Keyword(s):  
Cutting Force ◽  
Friction Angle ◽  
Hole Drilling ◽  
Force Model ◽  
Deep Hole ◽  
Drilling Force ◽  
Cutting Force Components ◽  
Distribution Laws ◽  
Force Components ◽  
Thrust And Torque

The boring and trepanning association (BTA) deep hole drilling is a typical self-guiding machining method. The drilling force and its distribution laws along the cutting radius directly affect the stability of drilling and the quality of machined hole. Based on the oblique cutting theory, a novel drilling force model is developed to predict the thrust and torque for staggered teeth BTA deep hole drill with variable geometries. Using the constraint relationships between the cutting force components and cutting angles, combined with the measured drilling force during the drill entrance, the parameters of the model including normal shear angle, normal friction angle and shear stress involved in the cutting force coefficients along the cutting radius, and the axial and circumferential friction coefficients between the guide pads and the hole wall are obtained. The model-predicted drilling force is validated by experimental results.

scholarly journals Trochoidal Milling and Neural Networks Simulation of Magnesium Alloys

Materials ◽  
2019 ◽  
Vol 12 (13) ◽  
pp. 2070 ◽  
Author(s):  
Ireneusz Zagórski ◽  
Monika Kulisz ◽  
Mariusz Kłonica ◽  
Jakub Matuszak
Keyword(s):  
Neural Networks ◽  
Cutting Force ◽  
Magnesium Alloys ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Milling Process ◽  
Machining Parameters ◽  
Cutting Force Components ◽  
Multilayered Perceptron ◽  
Force Components

This paper set out to investigate the effect of cutting speed vc and trochoidal step str modification on selected machinability parameters (the cutting force components and vibration). In addition, for a more detailed analysis, selected surface roughness parameters were investigated. The research was carried out for two grades of magnesium alloys—AZ91D and AZ31—and aimed to determine stable machining parameters and to investigate the dynamics of the milling process, i.e., the resulting change in the cutting force components and in vibration. The tests were performed for the specified range of cutting parameters: vc = 400–1200 m/min and str = 5–30%. The results demonstrate a significant effect of cutting data modification on the parameter under scrutiny—the increase in vc resulted in the reduction of the cutting force components and the displacement and level of vibration recorded in tests. Selected cutting parameters were modelled by means of Statistica Artificial Neural Networks (Radial Basis Function and Multilayered Perceptron), which, furthermore, confirmed the suitability of neural networks as a tool for prediction of the cutting force and vibration in milling of magnesium alloys.

INFLUENCE ON THE FEED-RATE AND MQF IN THE SURFACE ROUGHNESS AND CUTTING FORCE COMPONENTS DURING THE AISI 420C TURNING WITH STANDARD AND WIPER TOOLS.

2015 ◽  
Author(s):  
André Faraon Rodrigues ◽  
Cássio Magalhães dos Reis ◽  
Matheus Nunes Duran ◽  
Guilherme Cortelini da Rosa ◽  
André João de Souza
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Feed Rate ◽  
Cutting Force Components ◽  
Force Components
Sign in / Sign up

Export Citation Format

Share Document