Analysis of shear behavior between old concrete and fiber concrete

2021 ◽  
Author(s):  
Martin Vavruš ◽  
Peter Koteš ◽  
František Bahleda ◽  
Jozef Jošt
Keyword(s):  
Carrying Capacity ◽  
Research Work ◽  
Concrete Structures ◽  
Mechanical Damage ◽  
Load Carrying Capacity ◽  
Load Carrying ◽  
Fiber Concrete ◽  
Different Types ◽  
Thawing And Freezing Cycles

AbstractConcrete structures that are influenced by degradation, overloading, the thawing, and freezing cycles, corrosion of reinforced bars, should be repaired or strengthened. Each of the mentioned influences lead to decreased load-carrying capacity of the structure or its member. Exceeding the load-carrying capacity leads to mechanical damage of members or excessive deformation. The damaged member has to be strengthened to the required level of reliability and load-carrying capacity. There exist many types and methods of strengthening the columns. This research work deals with strengthening of columns by concreting a new layer of fiber concrete. When applying that type of strengthening, it is necessary to assure the contact between the old layer and the new one. The paper deals with analysis of different types of contacts and determination of their parametric values.

Influence of water contamination in gear lubricants on wear and micro-pitting performance of case carburized gears

2017 ◽  
Vol 69 (4) ◽  
pp. 612-619 ◽  
Author(s):  
Christian Engelhardt ◽  
Jochen Witzig ◽  
Thomas Tobie ◽  
Karsten Stahl
Keyword(s):  
Carrying Capacity ◽  
Research Work ◽  
Load Carrying Capacity ◽  
Wear Performance ◽  
Content Type ◽  
Effect Of Water ◽  
Base Oils ◽  
Load Carrying ◽  
Different Types ◽  
Influence Of Water

Purpose Water can alter the performance of modern gear lubricants by influencing the flank load carrying capacity of gears significantly. The purpose of this paper is to investigate the influence of water contaminations in different kinds of base oils on the micro-pitting and wear performance of case carburized gears. Design/methodology/approach Concerning micro-pitting and wear, tests, based mostly on the following standardized tests, are performed on a Forschungsstelle fuer zahnraeder und getriebebau (FZG)-back-to-back gear test rig: micro-pitting short test Graufleckenkurztest (GFKT) according to DGMK 575 (screening test), micro-pitting test Graufleckentest (GT) according to FVA 54/7 (load stage test and endurance test) and Slow-speed wear test according to DGMK 377. To investigate the effect of water on the gear load carrying capacity dependent on different types of base oils, two polyglycol oils (PG1 and PG2), a polyalphaolefin oil, a mineral oil and an ester oil E are used. Each of these oils are common wind turbine gear oils with a viscosity ISO VG-220. Additionally, a manual transmission fluid with a viscosity of society of automotive engineers (SAE) 75W-85 is tested. Findings Considering the micro-pitting and wear performance, a significant decrease caused by water contaminations could not be detected. Regarding pitting damages, a generally negative influence was observed. This influence was differently distinctive for different base oil types. Especially non-polar lubricants seem to be affected negatively. The documented damages of the tooth flanks confirm this observation. While typical pitting damages appeared in test runs with polar lubricants, the disruption in test runs with non-polar lubricants was more extensive. Based on the experimental investigations, a general model of the damaging mechanisms of water contaminations in lubricants was derived. It is split into three partitions: interaction lubricant–water (effect of water on the molecular structure of base oils and additives), chemical-material-technological (especially corrosive reactions) and tribological influence (effect of water droplets in the contact zone). It has to be considered that the additive package of lubricants affects the influence of water contaminations on the flank load carrying capacity distinctively. An influence of water on the micro-pitting and wear performance in other than the given lubricants cannot be excluded. Originality/value While former research work was focused more on the effects of water in mineral oils, investigations concerning different types of base oils as well as different types of damages were carried out within this research project.

scholarly journals Determination of Load-Carrying Capacity of C-Profile Glued Ti-Al Column under Temperature Environment

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3013
Author(s):  
Leszek Czechowski
Keyword(s):  
Carrying Capacity ◽  
Tensile Tests ◽  
Discrete Models ◽  
Image Correlation ◽  
Load Carrying Capacity ◽  
Lagrange Equations ◽  
Load Carrying ◽  
Different Temperatures ◽  
Influence Of Temperature On

The paper deals with an examination of the behaviour of glued Ti-Al column under compression at elevated temperature. The tests of compressed columns with initial load were performed at different temperatures to obtain their characteristics and the load-carrying capacity. The deformations of columns during tests were registered by employing non-contact Digital Image Correlation Aramis® System. The numerical computations based on finite element method by using two different discrete models were carried out to validate the empirical results. To solve the problems, true stress-logarithmic strain curves of one-directional tensile tests dependent on temperature both for considered metals and glue were implemented to software. Numerical estimations based on Green–Lagrange equations for large deflections and strains were conducted. The paper reveals the influence of temperature on the behaviour of compressed C-profile Ti-Al columns. It was verified how the load-carrying capacity of glued bi-metal column decreases with an increase in the temperature increment. The achieved maximum loads at temperature 200 °C dropped by 2.5 times related to maximum loads at ambient temperature.

Progressive Failure Analysis of an Integral Composite Joint for Thrust Reverser Cascade

2019 ◽  
Vol 795 ◽  
pp. 325-332
Author(s):  
Ji Shen Yang ◽  
Hong Yu Qi ◽  
Xiao Guang Yang ◽  
Duo Qi Shi
Keyword(s):  
Carrying Capacity ◽  
Composite Structure ◽  
Progressive Failure ◽  
Damage Model ◽  
Research Work ◽  
Failure Behavior ◽  
Load Carrying Capacity ◽  
Composite Joint ◽  
Bending Load ◽  
Load Carrying

The research work in this paper is focused on studying the failure behavior of an integral π-shaped laminated composite structure subjected to a bending load. A progressive damage model based on the 3D Tsai-Wu failure criterion and a developed gradual degradation model was employed to simulate and assess the load-carrying capacity, the onset and propagation of damage, and the failure mechanisms. For this unique π-shaped composite structure, disbonding was found to be the dominant damage mode under bending load, and the approximate maximum load could be maintained for a brief time during the final failure due to the gradual loss nature of the load-carrying capacity. The extent of damage was found to be more serious on the side of Rib II compared to the other side.

STABILITY PROBLEMS OF STEEL‐CONCRETE MEMBERS COMPOSED OF HIGH‐STRENGTH MATERIALS

2010 ◽  
Vol 16 (3) ◽  
pp. 352-362 ◽  
Author(s):  
Zdeněk Kala ◽  
Libor Puklický ◽  
Abayomi Omishore ◽  
Marcela Karmazínová ◽  
Jindřich Melcher
Keyword(s):  
Theoretical Analysis ◽  
Experimental Research ◽  
Carrying Capacity ◽  
High Strength ◽  
Statistical Characteristics ◽  
Load Carrying Capacity ◽  
Limit States ◽  
Load Carrying ◽  
Geometrical Imperfections

The presented paper deals with the stochastic analysis of the ultimate limit states of steel‐concrete building members. The load carrying capacity of steel‐concrete columns, comprising of steel profiles encased in high strength concrete, in compression is analyzed. The first part of the paper lists assumptions for the determination of the theoretical load carrying capacity of the column. Principles of elasticity and plasticity are used to determine stresses in the concrete and steel sections. Statistical characteristics of input material and geometrical imperfections are listed. Results of the theoretical analysis are then compared with results of experimental research. Statistical characteristics of obtained results of the theoretical analysis were verified using statistical characteristics obtained from experimental research. Numerical simulation LHS and Monte Carlo methods, which take into account the influences of variability of input imperfections, were employed. The influence of the utilization of the plastic reserve in the determination of the load carrying capacity of the analysed strut is shown. The influence of the initial geometric imperfections of initial strut curvature on the load carrying capacity is also presented. Santrauka Straipsnyje pateikta plienbetonio pastatu elementu didžiausiu ribiniu būkliu stochastine analize, analizuojama plienbetonio kolonu, sudarytu iš plieniniu profiliuočiu, padengtu didelio stiprio betonu, laikomoji galia gniuždant. Pirmoje straipsnio dalyje išvardytos kolonos teorines laikomosios galios nustatymo prielaidos. Tamprumo ir plastiškumo principai taikyti itempiams betono ir plieno skerspjūviuose nustatyti. Nustatytos medžiagu ir geometriniu defektu statistines charakteristikos, teorines analizes rezultatai palyginti su eksperimentiniu tyrimu rezultatais. Teorines analizes metu gautu rezultatu statistines charakteristikos patikrintos taikant iš eksperimentiniu tyrimu gautus statistinius rodiklius. Pritaikytas skaitinis modeliavimas LHS ir Monte Karlo metodais, kurie ivertina pradiniu defektu kintamumo itaka. Parodyta plastiškumo atsargos naudojimo itaka, nustatant analizuojamojo statramsčio laikomaja galia, pateikta pradinio statramsčio išlinkio pirminiu geometriniu defektu itaka laikomajai galiai.

Mechanical properties of confirmat screws corner joints made of native wood and wood-based composites

2019 ◽  
Vol 105 ◽  
pp. 76-84
Author(s):  
NADEŽDA LANGOVÁ ◽  
PAVOL JOŠČÁK
Keyword(s):  
Mechanical Properties ◽  
Carrying Capacity ◽  
Limit State ◽  
Calculated Data ◽  
Statistical Processing ◽  
Load Carrying Capacity ◽  
Load Carrying ◽  
Characteristic Values ◽  
State Method

Mechanical Properties of Confirmat Screws Corner Joints Made of Native Wood and Wood-Based Composites. The aim of this investigation was to design and determine the mechanical properties of confirmat screws corner joints made of native wood and wood-based composites. The objective of the study was to ascertain the stiffness and load carrying capacity of joints that differed in the diameter and length of confirmat type screw, as well as in the kind of materials. The results include statistical processing of measured and calculated data, and evaluation of the influence of selected factors on mechanical properties. The results are applied to the calculation of the characteristic values of the properties and to the determination of the equations for their calculation for other values of the selected factors. The characteristic values are used for the evaluation of the joints according to the limit state method.

Theoretical Analysis of Externally Pressurized Air Journal Bearing

1970 ◽  
Vol 12 (2) ◽  
pp. 123-129 ◽  
Author(s):  
B. C. Majumdar
Keyword(s):  
Experimental Data ◽  
Carrying Capacity ◽  
Reynolds Equation ◽  
Journal Bearing ◽  
Design Parameters ◽  
Load Carrying Capacity ◽  
Load Carrying ◽  
Dimensional Parameters ◽  
Bearing Design

A theoretical investigation is made to predict the performance of an externally pressurized air journal bearing having several pressure sources. The pressure distribution, which leads to the determination of load-carrying capacity and flow requirement, is obtained by solving Reynolds equation numerically. The load and flow, expressed in non-dimensional parameters, are presented for different bearing design parameters (dimensionless). The results predicted by this method are compared with others' experimental data.

Tribology of Lubricants

2021 ◽  
pp. 391-420
Keyword(s):  
Service Life ◽  
Tribological Properties ◽  
Carrying Capacity ◽  
Solid Lubricants ◽  
Load Carrying Capacity ◽  
Friction Control ◽  
Load Carrying ◽  
Different Types ◽  
Traction Fluids ◽  
The Relationship

Abstract This chapter covers the tribological properties of different types of oil, greases, solid lubricants, and metalworking and traction fluids. It explains how lubricants are made, how they work, and how they are applied and tested. It also discusses the fundamentals of lubrication and friction control, the relationship between viscosity and breakaway friction, and the factors that affect load-carrying capacity and service life.

Sign in / Sign up

Export Citation Format

Share Document