Effect of the ridge tillage system on some selected soil physical properties in a maize monoculture

2004 ◽  
Vol 52 (3) ◽  
pp. 211-220 ◽  
Author(s):  
P. László ◽  
C. Gyuricza

Within the framework of cooperation between Szent István University and the Vienna University of Agricultural Sciences, a soil cultivation experiment in a maize (Zea mays L.) monoculture was set up for the first time in Austria near Pyhra (Lower Austria) in 1996. A study was conducted to evaluate the effects of ridge tillage (RT) in comparison with conventional mouldboard ploughing in autumn (CT) and no-tillage (NT) on the penetration resistance (PR), soil bulk density (BD) and porosity (P) of sandy loam soil (Typic Agriudoll). Analyses were made for each treatment and for different parts of the ridge (top and side of the ridge, and interrow) in 1998, 2000 and 2002. The average PR and BD values were greatest in the no-tillage plot, being 3.42 MPa and 1.56 g·cm-3, respectively. After six years, ridge tillage resulted in lower penetration resistance and bulk density values in the upper 20 cm than conventional tillage and no-tillage. Ridge tillage appears capable of reducing compaction in this soil. It can be concluded from the results that ridge tillage is capable of maintaining and improving favourable physical conditions in the soil.

2008 ◽  
Vol 23 (2) ◽  
pp. 107-114
Author(s):  
Milena Simic ◽  
Nebojsa Momirovic ◽  
Zeljko Dolijanovic ◽  
Zeljko Radosevic

The effects of different herbicide combinations: control (1), alachlor+linuron (2), and alachlor+linuron+imazethapyr (3) were investigated in double-cropped soybean grown in two row spacing variants, 38 cm and 76 cm, under conventional tillage (CT) or no-tillage (NT). In trials conducted on a sandy loam soil at Zemun Polje, high weediness had a negative effect of on the yield of double-cropped soybean, especially at the higher row spacing tested and with no-tillage. Regression and correlation data revealed a dependence of weediness in double-cropped soybean on tillage system and herbicide combination, and dependence of soybean yield on tillage system.


2010 ◽  
Vol 34 (1) ◽  
pp. 211-2178 ◽  
Author(s):  
Fabiana de Souza Pereira ◽  
Itamar Andrioli ◽  
Amauri Nelson Beutler ◽  
Cinara Xavier de Almeida ◽  
Faber de Souza Pereira

The intensive use of land alters the distribution of the pore size which imparts consequences on the soil physical quality. The Least Limiting Water Range (LLWR) allows for the visualization of the effects of management systems upon either the improvement or the degradation of the soil physical quality. The objective of this study was to evaluate the physical quality of a Red Latosol (Oxisol) submited to cover crops in the period prior to the maize crop in a no-tillage and conventional tillage system, using porosity, soil bulk density and the LLWR as attributes. The treatments were: conventional tillage (CT) and a no-tillage system with the following cover crops: sunn hemp (Crotalaria juncea L.) (NS), pearl millet (Pennisetum americanum (L.) Leeke) (NP) and lablab (Dolichos lablab L.) (NL). The experimental design was randomized blocks in subdivided plots with six replications, with the plots being constituted by the treatments and the subplots by the layers analyzed. The no-tillage systems showed higher total porosity and soil organic matter at the 0-0.5 m layer for the CT. The CT did not differ from the NL or NS in relation to macroporosity. The NP showed the greater porosity, while CT and NS presented lower soil bulk density. No < 10 % airing porosity was found for the treatments evaluated, and value for water content where soil aeration is critical (θPA) was found above estimated water content at field capacity (θFC) for all densities. Critical soil bulk density was of 1.36 and 1.43 Mg m-3 for NP and CT, respectively. The LLWR in the no-tillage systems was limited in the upper part by the θFC, and in the bottom part, by the water content from which soil resistance to penetration is limiting (θPR). By means of LLWR it was observed that the soil presented good physical quality.


1998 ◽  
Vol 12 (2) ◽  
pp. 281-285 ◽  
Author(s):  
Karen A. Renner ◽  
Oliver Schabenberger ◽  
James J. Kells

Field studies on a sandy loam soil determined the influence of application method and rate and subsequent tillage on corn response to imazaquin and imazethapyr residues remaining in the soil. Imazaquin was applied preplant incorporated (PPI) and preemergence (PRE) at 70, 140, and 280 g ai/ha and postemergence (POST) at 70 and 140 g/ha. Imazethapyr was applied PPI and PRE at 70, 105, and 140 g ai/ha and POST at 70 and 105 g/ha. Subsequent tillage included fall moldboard plowing followed by spring field cultivation, fall chisel plowing followed by spring field cultivation, and no tillage. Herbicide dissipation was determined by analyzing soil cores taken in the spring at the time of corn planting and by measuring corn height and grain yield. Imidazolinone residues were detected in only 1 of 2 yr. Imazaquin was detected more frequently than imazethapyr. Imazaquin concentrations in the upper 10 cm of soil 11 mo after a PPI application of 280 g/ha were 5, 6, and 7 ng/g of soil in moldboard plow, chisel, and no-tillage systems, respectively. Imazaquin (5 ng/g) was also detected in the 10–18-cm soil depth in the moldboard plow system. Corn height and grain yield were not reduced from imazaquin or imazethapyr, regardless of application method or rate in any tillage system.


Poljoprivreda ◽  
2020 ◽  
Vol 26 (1) ◽  
pp. 17-24
Author(s):  
Miro Stošić ◽  
Vladimir Zebec ◽  
Maciej Kluz ◽  
Boris Ravnjak ◽  
Tomislav Vinković ◽  
...  

A stationary field experiment of a reduced soil tillage was implemented at a Hypogley (Hypogleyic soils A–Gso–Gr soil horizon sequence) soil type of Eastern Croatia during three seasons and set up as a split-plot randomized block design in four repetitions. The tillage systems (TS) were as follows: 1) conventional tillage, i.e., plowing at 30 cm (CT), 2) disking up 10-12 cm (DT), 3) soil loosening up to 35 cm (LT), 4) no-tillage (NT). The experiment was designed to compare the penetration resistance (PR), soil moisture (SM), and bulk density (BD) at different TSs and soil depths. A cone penetrometer was used to measure the PR with 10 prods per TS, accompanied with a measurement of SM with a soil auger on every 10 cm, with four samples up to a 40-cm depth. The BD was determined by metal cylinders on every 10 cm up to a 30-cm depth, being weighed and dried thereafter to obtain an absolutely dry sample, and then calculated using absolutely a dry soil sample mass (m_s) and the soil volume (V). The PR and SM were significantly influenced by the TS and soil depth. The CT had the significantly lowest PR at all depths, while the DT has manifested a significantly higher PR at a soil depth amounting to 10 to 20 cm. The PR on NT were significantly diverse from the CT at all soil depths. The BD varied significantly concerning the TS and the soil depth. Subsequent to the three years, the CT had a significantly smaller BD at a depth amounting from 0 to 10 cm, and a significantly higher BD at 20- to 30-cm depth, compared to reduce the TS.


2005 ◽  
Vol 84 (1) ◽  
pp. 41-53 ◽  
Author(s):  
R.F. Dam ◽  
B.B. Mehdi ◽  
M.S.E. Burgess ◽  
C.A. Madramootoo ◽  
G.R. Mehuys ◽  
...  

2021 ◽  
Vol 17 (4) ◽  
pp. 295-300
Author(s):  
P.O.O. Dada ◽  
J.J. Musa ◽  
O.O. Olla ◽  
J.O. Ohu ◽  
J.K. Adewumi

Soil compaction has effect on soil physical properties which could affect crop growth and yield. This study was conducted to determine the influence of incorporating organic materials and load application (tractorization) on the physical properties of sandy loamy soil in Abeokuta, Ogun State, Nigeria. Organic materials were cow dung, poultry and swine manure. Application rates of organic manures were 0 (control), 5 and 10 tonnes per hectare. Forty-five plots measuring 5 by 3 m were established in a complete randomized block experimental design with three replications making a total of 135 plots. Load application was done using an MF 435 tractor coupled with a 20-disc harrow at 0 (control), 5, 10, 15 and 20 passes. Penetration resistance, bulk density, gravimetric moisture content andporosity were determined using standard procedures. Penetrometer resistance at these passes were 392.2, 293.3, 285.0, 302.0 and 224.9 kPa respectively with significant differences between treatments (P≤0.05). Mean bulk density for the passes were 1.21, 1.26, 1.31, 1.27 and 1.29 g/cm3 respectively and bulk density increased with tractor passes. The effect of tractor passes, and manure incorporation rate did not have any significant effect on gravimetric moisture content. Poultry manure increased bulk density and penetrometer resistance on plots than swine manure and cow dung hence poultry manure at 10 t/ha can be incorporated on a sandy loam soil to enhance soil fertility and sustainability. Keywords: Tractorization, organic manure, sandy loam, penetration resistance, bulk density


2018 ◽  
Vol 71 (3) ◽  
Author(s):  
Dorota Gawęda ◽  
Andrzej Woźniak ◽  
Elżbieta Harasim

In-crop weed infestation is affected by both habitat conditions and agronomic practices, including the forecrop and tillage treatments used. This study evaluated the effect of the forecrop and the tillage system on species composition, number and dry weight of weeds in a winter wheat ‘Astoria’. A field study was carried out over the period 2014–2017 at the Uhrusk Experimental Farm (SE Poland), on a mixed rendzina soil with a grain-size distribution of sandy loam. Wheat was grown in a four-course crop rotation: soybean – winter wheat – rapeseed – winter wheat. The experimental factors were as follows: a forecrop of winter wheat (soybean and winter rapeseed) and a tillage system (ploughing and no-tillage). <em>Avena fatua</em> was the most frequently occurring weed in the wheat crop sown after soybean, whereas after winter rapeseed it was <em>Viola arvensis</em>. <em>Viola arvensis</em> was the dominant weed under both tillage systems. In all experimental treatments, the species <em>Viola arvensis</em> and <em>Cirsium arvense</em> were characterized by the highest constancy (Constancy Class V and IV), and also <em>Veronica arvensis</em> after the previous winter rapeseed crop. In the wheat crop sown after winter rapeseed, the number of weeds was found to be higher by 62.1% and the weed dry weight higher by 27.3% compared to these parameters after the previous soybean crop. A richer floristic composition of weeds was also observed in the stand after winter rapeseed. Under conventional tillage conditions, compared to no-tillage, the number of weeds was found to be lower by 39.7% and their dry weight by 50.0%. An increase in the numbers of the dominant weed species was also noted in the untilled plots.


2013 ◽  
Vol 59 (No. 7) ◽  
pp. 295-302 ◽  
Author(s):  
B. Ji ◽  
Y. Zhao ◽  
X. Mu ◽  
K. Liu ◽  
C. Li

Subsoil compaction can result in unfavourable soil physical conditions and hinder the root growth of maize. The effects of deep tillage and conventional tillage on soil physical properties and root growth of maize were studied during 2010&ndash;2011 at two sites (loam at Hebi and clay at Luohe) in central China. The results showed that soil penetration resistance, bulk density, water content and root length density were significantly affected by tillage, soil depth and year. Deep tillage had lower penetration resistance and lower soil bulk density, but higher soil water content than conventional tillage across years and depths. Averaged over the whole soil profile, deep tillage not only significantly decreased penetration resistance and soil bulk density, but significantly increased soil water content and root length density on loam, while deep tillage only significantly increased the root length density on clay. We conclude that deep tillage on the loam is more suitable for the root growth of summer maize.


2015 ◽  
Vol 39 (3) ◽  
pp. 871-879 ◽  
Author(s):  
Adriano Stephan Nascente ◽  
Yuncong Li ◽  
Carlos Alexandre Costa Crusciol

Soil aggregation and the distribution of total organic carbon (TOC) may be affected by soil tillage and cover crops. The objective of this study was to determine the effects of crop rotation with cover crops on soil aggregation, TOC concentration in the soil aggregate fractions, and soil bulk density under a no-tillage system (NTS) and conventional tillage system (CTS, one plowing and two disking). This was a three-year study with cover crop/rice/cover crop/rice rotations in the Brazilian Cerrado. A randomized block experimental design with six treatments and three replications was used. The cover crops (treatments) were: fallow, Panicum maximum, Brachiaria ruziziensis, Brachiaria brizantha, and millet (Pennisetum glaucum). An additional treatment, fallow plus CTS, was included as a control. Soil samples were collected at the depths of 0.00-0.05 m, 0.05-0.10 m, and 0.10-0.20 m after the second rice harvest. The treatments under the NTS led to greater stability in the soil aggregates (ranging from 86.33 to 95.37 %) than fallow plus CTS (ranging from 74.62 to 85.94 %). Fallow plus CTS showed the highest number of aggregates smaller than 2 mm. The cover crops affected soil bulk density differently, and the millet treatment in the NTS had the lowest values. The cover crops without incorporation provided the greatest accumulation of TOC in the soil surface layers. The TOC concentration was positively correlated with the aggregate stability index in all layers and negatively correlated with bulk density in the 0.00-0.10 m layer.


2015 ◽  
Vol 29 (4) ◽  
pp. 441-447 ◽  
Author(s):  
Michel Keisuke Sato ◽  
Herdjania Veras de Lima ◽  
Pedro Daniel de Oliveira ◽  
Sueli Rodrigues

Abstract The aim of this study was to evaluate the critical soil bulk density from the soil penetration resistance measurements for soybean root growth in Brazilian Amazon Oxisols. The experiment was carried out in a greenhouse using disturbed soil samples collected from the northwest of Para characterized by different texture. The treatments consisted of a range of soil bulk densities for each soil textural class. Three pots were used for soybean growth of and two for the soil penetration resistance curve. From the fitted model, the critical soil bulk density was determined considering the penetration resistance values of 2 and 3 MPa. After sixty days, plants were cut and root length, dry mass of root, and dry mass of shoots were determined. At higher bulk densities, the increase in soil water content decreased the penetration resistance, allowing unrestricted growth of soybean roots. Regardless of soil texture, the penetration resistance of 2 and 3 MPa had a slight effect on root growth in soil moisture at field capacity and a reduction of 50% in the soybean root growth was achieved at critical soil bulk density of 1.82, 1.75, 1.51, and 1.45 Mg m-3 for the sandy loam, sandy clay loam, clayey, and very clayey soil.


Sign in / Sign up

Export Citation Format

Share Document