Kinetic study and modeling of the solid-state reaction Y2BaCuO5 + 3BaCuO2 + 2CuO ⇉ 2YBa2Cu3O6.5−x + xO2

1990 ◽  
Vol 5 (10) ◽  
pp. 2056-2065 ◽  
Author(s):  
Nae-Lih Wu ◽  
Ta-Chin Wei ◽  
Shau-Y Hou ◽  
S-Yen Wong
Keyword(s):  
Particle Size ◽  
Solid State ◽  
Solid State Reaction ◽  
Size Dependence ◽  
Average Particle Size ◽  
Average Particle ◽  
Fractional Conversion ◽  
X Ray ◽  
Unreacted Core ◽  
Kinetics Of

The kinetics of the solid-state reaction Y2BaCuO5 + 3BaCuO2 + 2CuO ⇉ 2YBa2Cu3O6.5−x + xO2 was studied by using x-ray diffractometric and thermogravimetric analyses. Both analyses established that the reaction was well described by the kinetic equation: 1 − 3(1 − F)2/3 + 2(1 − F) = k0 exp(− E/RT)t, where F is the fractional conversion of a calcined powder, E is 520 kcal/molc and, for a rcactant mixture with an average particle size of 3 μm, k0 is 2.03 ⊠ 1092 min−1. An unreacted-core shrinking model was proposed to obtain the particle-size dependence of the reaction, and predicted that the pre-exponential constant k0 changed with reactant particle size by k0 = 2.03 ⊠ 1092(3/d)2 exp(4/d − 4/3), where d is the average reactant particle size in μm.

scholarly journals Growth of significantly low dimensional zinc orthotitanate (Zn2TiO4) nanoparticles by solid state reaction method

2018 ◽  
Vol 50 (1) ◽  
pp. 133-138 ◽  
Author(s):  
Lizina Khatua ◽  
Rudrashish Panda ◽  
Avanendra Singh ◽  
Arpan Nayak ◽  
Pravakar Satapathy ◽  
...  
Keyword(s):  
Particle Size ◽  
Solid State ◽  
Surface Area ◽  
Solid State Reaction ◽  
Average Particle Size ◽  
Cost Effective ◽  
Solid State Reaction Method ◽  
Average Particle ◽  
Reaction Method ◽  
Low Dimensional

In this work, the ZnO-TiO2 mixed phase nanoparticles were prepared by solid state reaction method by using ZnO and TiO2 powder as precursors. The X-ray diffraction pattern shows a dominant phase of Zinc Orthotitanate (Zn2TiO4). The average particle size (58?18 nm) calculated by the analysing FESEM data closely matches with the particle size calculated by Scherrer?s equation. The calculated average particle size is significantly smaller than the previously published results of nanoparticles, prepared by same method. In the Brunauer-Emmett-Teller (BET) study the specific surface area of the nanoparticles was found as 8.78 m2/g which is similar to the surface area reported in this material prepared by mechanochemical method. The method which we report is simpler and cost effective unlike the previous reported.

scholarly journals Pengaruh Doping Cu terhadap Karakteristik Material dan Ketahanan Karbon pada Anoda Ni1-X-CuX-BCZY untuk PSOFC

2020 ◽  
Vol 11 (3) ◽  
pp. 441-447
Author(s):  
Nanang Setiawan ◽  
◽  
Chung-Jen Tseng ◽  
Chin Tien Shen ◽  
ING Wardana ◽  
...  
Keyword(s):  
Particle Size ◽  
Solid State ◽  
Electron Scattering ◽  
Solid State Reaction ◽  
Metal Particle ◽  
Average Particle Size ◽  
Average Particle ◽  
Calcination Time ◽  
Microstructure Characteristics

The purpose of this study is to investigate the microstructure characteristics of the Ni1-xCux-BCZY anode and to analyze the carbon resistance by doping Cu into the Ni-BCZY anode. Ni1-xCux and BaCe0.7Zr0.1Y0.2O3-𝛿 (BCZY) powder were prepared by solid-state reaction with Ni1-xCux /BCZY = 60:40 wt%. The powder is calcined at a temperature of 700 °C, sintered at 1450 °C, and reduced by pure H2. The results of the Ni1-xCux-BCZY microstructure show an increase in the average particle size from 2.71 to 2.88 µm with increasing calcination time from 0.5 to 1.5 hours. Furthermore, the conductivity of Ni1-xCux-BCZY (x = 0.1) is lower than Ni1-xCux-BCZY (x = 0), this is associated with enhancement electron scattering, which correlatives with large metal particle obtained. The optimum conductivity of Ni1-xCux-BCZY(x=0.1) is obtained at a calcination time of 0.5 hours. Furthermore, NiCu anode can effectively increase the carbon resistance while using methane as a fuel.

scholarly journals Thermal, Structural, and Physical Properties of Freeze Dried Tropical Fruit Powder

2014 ◽  
Vol 2014 ◽  
pp. 1-10 ◽  
Author(s):  
K. A. Athmaselvi ◽  
C. Kumar ◽  
M. Balasubramanian ◽  
Ishita Roy
Keyword(s):  
Particle Size ◽  
Physical Properties ◽  
Average Particle Size ◽  
Average Particle ◽  
X Ray Diffraction ◽  
Tropical Fruit ◽  
X Ray ◽  
Freeze Dried ◽  
Fruit Powder ◽  
Lcr Meter

This study evaluates the physical properties of freeze dried tropical (guava, sapota, and papaya) fruit powders. Thermal stability and weight loss were evaluated using TGA-DSC and IR, which showed pectin as the main solid constituent. LCR meter measured electrical conductivity, dielectric constant, and dielectric loss factor. Functional groups assessed by FTIR showed presence of chlorides, and O–H and N–H bonds in guava, chloride and C–H bond in papaya, and chlorides, and C=O and C–H bonds in sapota. Particle size and type of starch were evaluated by X-ray diffraction and microstructure through scanning electronic microscopy. A semicrystalline profile and average particle size of the fruit powders were evidenced by X-ray diffraction and lamellar/spherical morphologies by SEM. Presence of A-type starch was observed in all three fruits. Dependence of electric and dielectric properties on frequency and temperature was observed.

scholarly journals Preparation of ultrafine iron phosphate micro-powder from phosphate slag

2018 ◽  
Vol 238 ◽  
pp. 02002
Author(s):  
Fangjing Sun ◽  
Yi Zhang ◽  
Jiawei Zhang ◽  
Xixi Yan ◽  
Xiaoyu Liu ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Particle Size ◽  
Electron Microscope ◽  
Average Particle Size ◽  
Iron Phosphate ◽  
Average Particle ◽  
X Ray ◽  
Particle Size Analyzer ◽  
Phosphate Slag ◽  
Scanning Electron

In this experiment, ultrafine iron phosphate micro-powder was prepared by hydrothermal method which used phosphate slag as an iron source. The effects of reaction temperature, surfactants type and amount on its particle size were explored. The samples were characterized by using Malvern Laser Particle Size Analyzer (MS2000), X-Ray Diffractometer (XRD), Scanning Electron Microscope (SEM) and Energy Dispersive X-Ray Spectroscopy (EDX).The results showed that at 160 °C, 1 wt%CTAB, monoclinic iron phosphate micro-powder was obtained with an average particle size about 0.4 μm which also has a good dispersion in aqueous solution.

Morphology-Controlled CaCO3 Nanostructures by Modified Co-Precipitation in Pulsed Mode

2015 ◽  
Vol 752-753 ◽  
pp. 148-153
Author(s):  
M.M. Nassar ◽  
Taha Ebrahiem Farrag ◽  
M.S. Mahmoud ◽  
Sayed Abdelmonem
Keyword(s):  
Particle Size ◽  
Calcium Carbonate ◽  
Rotation Speed ◽  
Average Particle Size ◽  
Calcium Nitrate ◽  
Precipitation Method ◽  
Average Particle ◽  
X Ray ◽  
Co Precipitation ◽  
Pulsed Mixing

Calcium carbonate nanoparticles and nanorods were synthesized by precipitation from saturated sodium carbonate and calcium nitrate aqueous solutions through co precipitation method. A new rout of synthesis was done by both using pulsed mixing method and controlling the addition of calcium nitrate. The effect of the agitation speed, and the temperature on particle size and morphology were investigated. Particles were characterized using X-ray Microanalysis, X-ray analysis (XRD) and scanning electron microscopy (SEM). The results indicated that increasing the mixer rotation speed from 3425 to 15900 (rpm) decreases the average particle size to 64±7 nm. A rapid nucleation then aggregation induced by excessive shear force phenomena could explain this observation. Moreover, by increasing the reaction temperature, the products were converted from nanoparticle to nanorods. The maximum attainable aspect ratio was 6.23 at temperature of 75°C and rotation speed of 3425. Generally, temperature raise promoted a significant homoepitaxial growth in one direction toward the formation of calcite nanorods. Overall, this study can open new avenues to control the morphology of the calcium carbonate nanostructures.

Fabrication and Characterization of Nanospinel ZnCr2O4 Using Thermal Treatement Method

2015 ◽  
Vol 1107 ◽  
pp. 301-307 ◽  
Author(s):  
Salahudeen A. Gene ◽  
Elias B. Saion ◽  
Abdul Halim Shaari ◽  
Mazliana A. Kamarudeen ◽  
Naif Mohammed Al-Hada
Keyword(s):  
Particle Size ◽  
Calcination Temperature ◽  
Average Particle Size ◽  
Treatment Method ◽  
Esr Spectra ◽  
Resonance Spectroscopy ◽  
Average Particle ◽  
Face Centered Cubic ◽  
X Ray ◽  
Xrd Patterns

The fabrication of nanospinel zinc chromite (ZnCr2O4) crystals by the means of thermal treatment method from an aqueous solution containing metal nitrates, polyvinyl pyrrolidone (PVP), and deionized water was described in this study. The samples were calcined at various temperatures ranging from 773 to 973 K for the decomposition of the organic compounds and crystallization of the nanocrystals. PVP was used as capping agent to control the agglomeration of the particles. The characterization studies of the fabricated samples were carried out by X-ray diffraction spectroscopy (XRD), transmission electron microscopy (TEM), energy dispersed X-ray spectroscopy (EDX) and electron spin resonance spectroscopy (ESR). The corresponding peaks of Zn, Cr and O were observed in the EDX spectrum of the sample which confirms the formation of ZnCr2O4. The XRD patterns also confirmed the formation of the single faced nanocrystallines of spinel ZnCr2O4 with a face-centered cubic structure. The average particle size of the synthesized crystals was also determined from the XRD patterns using the Scherers formula which shows that the crystallite sizes increases with increase in calcination temperature and was in good agreement with the TEM images which shows cubical ZnCr2O4 nanocrystals with uniform morphology and particle size distributions. The ESR spectra confirmed the existence of unpaired electron in the fabricated samples and the increase in g-factor and decreases in resonant magnetic field (Hr) were observed as the calcination temperature increases.

Process Parameters Optimization of Direct Synthesis Nano Magnesium Fluoride Powders

2012 ◽  
Vol 184-185 ◽  
pp. 1146-1149
Author(s):  
Ping Li ◽  
Hai Yang Wang ◽  
Wan E Wu ◽  
Shuai Ling
Keyword(s):  
Particle Size ◽  
Orthogonal Experiment ◽  
Direct Synthesis ◽  
Average Particle Size ◽  
Parameters Optimization ◽  
Magnesium Fluoride ◽  
Process Conditions ◽  
Average Particle ◽  
X Ray ◽  
Mgcl2 Concentration

To reduce average particle size，magnesium fluoride was directly synthesized from MgF2 and NH4F，the product was characterized by X-ray diffractomer，scanning electron microscopy. Orthogonal experiment was used to explore the influences of factors on the average particle size. Found that the effect order of factors on the average particle size is MgCl2 concentration，NH4F concentration，reaction temperature，reaction time，in the optimization of process conditions，average particle size is 23.1 nm.

Influences of Firing Temperatures on Phase and Morphology Evolution of (Ba0.25Sr0.75)(Zr0.75Ti0.25)O3 Ceramics Synthesized via Solid-State Reaction Method

2009 ◽  
Vol 421-422 ◽  
pp. 247-250 ◽  
Author(s):  
Atthakorn Thongtha ◽  
Kritsana Angsukased ◽  
Theerachai Bongkarn
Keyword(s):  
Solid State ◽  
Solid State Reaction ◽  
Perovskite Phase ◽  
Average Particle Size ◽  
Solid State Reaction Method ◽  
Lattice Parameter ◽  
Average Particle ◽  
Strontium Zirconate ◽  
Reaction Method ◽  
Average Grain Size

The effect of calcination (1000-1400 oC) and sintering temperatures (1400-1600 oC) on the phase formation and microstructure of barium strontium zirconate titanate [(Ba0.25Sr0.75)(Zr0.75Ti0.25)O3; BSZT] ceramics were investigated. BSZT powders were prepared by the solid-state reaction method. Higher calcination temperatures increased the percentage of the perovskite phase, but decreased the lattice parameter a of BSZT powders. The pure perovskite phase of BSZT powders was detected above the calcination temperature of 1350 oC. The microstructure of BSZT powders exhibited an almost-spherical morphology and had a porous agglomerated form. The average particle size and the average grain size of the ceramics were increased with the increase of calcination and sintering temperatures. The highest density of the samples was 5.42 g/cm3 which was obtained from ceramic sintered at 1550 oC for 2 h.

Structural, Optical and Magnetic Properties of Ni Doped ZnS Nanoparticles

2018 ◽  
Vol 24 (8) ◽  
pp. 5640-5644
Author(s):  
B Sreenivasulu ◽  
S. Venkatramana Reddy ◽  
P. Venkateswara Reddy
Keyword(s):  
Electron Microscopy ◽  
Particle Size ◽  
Absorption Spectra ◽  
Spherical Surface ◽  
Room Temperature Ferromagnetism ◽  
Average Particle Size ◽  
Precipitation Method ◽  
Chemical Compositions ◽  
Average Particle ◽  
X Ray

Pure ZnS and 3 mol% of Ni doped ZnS nano powders are prepared by chemical co-precipitation method. Properties of ZnS: Ni2+ nanoparticles are studied by X-ray diffraction Spectra (XRD), Raman spectroscopy (RS), Photoluminescence (PL), Absorption Spectra, Scanning electron microscopy (SEM), Energy-dispersive X-ray spectroscopy (EDAX), Transmission electron microscopy (TEM) and Vibrating sample magnetometer (VSM). From XRD data, it conform the structure of ZnS, and particle size of pure and Ni doped ZnS data indicates the incorporation of Ni2+ in ZnS nanocrystal lattice. Raman spectra for pure and Ni doped samples exhibited vibrational modes confirm the structure of ZnS. Photoluminescence spectra reveal that the emission peaks are in UV and visible regions; this is confirming the absorption spectra. SEM micrographs show spherical morphology, and chemical compositions of samples are in stoichiometric proportions. TEM micro graphs show the spherical surface morphology and average particle size for pure and Ni2+ doped nanoparticles are in the range of 2–3 nm, this is good agreement with XRD results. M–H curves from VSM show room temperature ferromagnetism.

Sign in / Sign up

Export Citation Format

Share Document