Effect of Thermal Treatment on the Photocatalytic Activity of TiO2 Coatings for Photocatalytic Oxidation of Benzoic Acid

2002 ◽  
Vol 17 (7) ◽  
pp. 1758-1765 ◽  
Author(s):  
Alex H. C. Chan ◽  
John F. Porter ◽  
John P. Barford ◽  
Chak K. Chan
Keyword(s):  
Stainless Steel ◽  
Thermal Treatment ◽  
Benzoic Acid ◽  
Surface Area ◽  
Photocatalytic Oxidation ◽  
Steel Plates ◽  
X Ray Diffraction ◽  
X Ray ◽  
316 Stainless Steel ◽  
Unheated Sample

The effects of thermal treatment on the properties and photoactivities of TiO2 catalysts supported on 316 stainless steel plates were examined. Degussa P-25 was immobilized on 316 stainless steel plates by electrophoretic deposition. These TiO2-coated plates were heated at 473, 673, and 873 K for 1 h. The photoactivities of these TiO2 coatings were determined based on the removal of benzoic acid as the model pollutant. In particular, the photoactivity decreased by 52% in the sample heated at 873 K compared with the unheated sample. The results of x-ray diffraction showed that the crystallinity and the crystallite sizes of the catalysts supported on the plates did not significantly vary with increasing temperature over the range examined. Negligible change in the catalyst phase (the anatase-to-rutile ratio) was indicated from x-ray diffraction and micro-Raman spectroscopy. However, it was found that the Brunauer–Emmett–Teller surface area of the scraped catalysts heated at 873 K decreased by nearly 13% compared with the unheated sample. In addition, scanning electron microscopy/energy dispersive x-ray and x-ray photoelectron spectroscopy analyses also detected the presence of Fe3+ ions at the surface of the supported catalysts heated at 873 K. The drop in surface area and the presence of Fe3+ ions at the catalyst surface, which were considered to function as electron–hole recombination centers, were possible factors leading to the drop in the photoactivity exhibited by the sample. A lower temperature for thermal treatment such as 473 K was proposed to ensure the coating stability and the catalyst photoactivity.

X-Ray Diffraction Analysis of Defects in Cold Worked Type 316 Stainless Steel

2011 ◽  
Author(s):  
S. Murugesan ◽  
P. Kuppusami ◽  
E. Mohandas ◽  
M. Vijayalakshmi ◽  
Alka B. Garg ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Diffraction Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
316 Stainless Steel ◽  
Cold Worked

scholarly journals X-Ray diffraction technique applied to study of residual stresses after welding of duplex stainless steel plates

2014 ◽  
Vol 17 (suppl 1) ◽  
pp. 64-69 ◽  
Author(s):  
Vladimir Ivanovitch Monin ◽  
Ricardo Tadeu Lopes ◽  
Sergio Nolêto Turibus ◽  
João C. Payão Filho ◽  
Joaquim Teixeira de Assis
Keyword(s):  
Stainless Steel ◽  
Residual Stresses ◽  
Duplex Stainless Steel ◽  
Steel Plates ◽  
X Ray Diffraction ◽  
X Ray

scholarly journals Hydrochloric Acid Modification and Lead Removal Studies on Naturally Occurring Zeolites from Nevada, New Mexico, and Arizona

Processes ◽  
2021 ◽  
Vol 9 (7) ◽  
pp. 1238
Author(s):  
Garven M. Huntley ◽  
Rudy L. Luck ◽  
Michael E. Mullins ◽  
Nick K. Newberry
Keyword(s):  
New Mexico ◽  
Surface Area ◽  
Bet Surface Area ◽  
Lead Removal ◽  
X Ray Diffraction ◽  
Sem Images ◽  
X Ray ◽  
Naturally Occurring ◽  
27Al Mas Nmr ◽  
Modified Zeolites

Four naturally occurring zeolites were examined to verify their assignments as chabazites AZLB-Ca and AZLB-Na (Bowie, Arizona) and clinoptilolites NM-Ca (Winston, New Mexico) and NV-Na (Ash Meadows, Nevada). Based on powder X-ray diffraction, NM-Ca was discovered to be mostly quartz with some clinoptilolite residues. Treatment with concentrated HCl (12.1 M) acid resulted in AZLB-Ca and AZLB-Na, the chabazite-like species, becoming amorphous, as confirmed by powder X-ray diffraction. In contrast, NM-Ca and NV-Na, which are clinoptilolite-like species, withstood boiling in concentrated HCl acid. This treatment removes calcium, magnesium, sodium, potassium, aluminum, and iron atoms or ions from the framework while leaving the silicon framework intact as confirmed via X-ray fluorescence and diffraction. SEM images on calcined and HCl treated NV-Na were obtained. BET surface area analysis confirmed an increase in surface area for the two zeolites after treatment, NM-Ca 20.0(1) to 111(4) m2/g and NV-Na 19.0(4) to 158(7) m2/g. 29Si and 27Al MAS NMR were performed on the natural and treated NV-Na zeolite, and the data for the natural NV-Na zeolite suggested a Si:Al ratio of 4.33 similar to that determined by X-Ray fluorescence of 4.55. Removal of lead ions from solution decreased from the native NM-Ca, 0.27(14), NV-Na, 1.50(17) meq/g compared to the modified zeolites, 30 min HCl treated NM-Ca 0.06(9) and NV-Na, 0.41(23) meq/g, and also decreased upon K+ ion pretreatment in the HCl modified zeolites.

Physico-Chemical and Morphological Changes of Sayong Kaolinite Clay Treated with Sulphuric Acid for Enzyme Immobilization

2013 ◽  
Vol 832 ◽  
pp. 589-595 ◽  
Author(s):  
N.A. Edama ◽  
A. Sulaiman ◽  
K.H. Ku Hamid ◽  
M.N. Muhd Rodhi ◽  
Mohibah Musa ◽  
...  
Keyword(s):  
Surface Area ◽  
Sulphuric Acid ◽  
Enzyme Immobilization ◽  
Morphological Changes ◽  
Chemical Properties ◽  
X Ray Diffraction ◽  
Kaolinite Clay ◽  
X Ray ◽  
Mineral Oxides ◽  
Physico Chemical

This study analyzed the effects of sulphuric acid (H2SO4) treatment on pysico-chemical properties and morphological changes of clay obtained from Sg. Sayong, Perak. The clay was ground and sieved to <150μm and treated with different concentrations of H2SO4. The treatment was completed by refluxing the clay with different concentration of H2SO4 (1M, 5M and 10M ) at 100 °C for 4 hours and followed by calcination at 500 °C for 1 hour. The physic-chemical properties and morphological changes of the untreated and treated clay were compared using Surface Area Analyser, X-Ray Diffraction (XRD), Field Emission Scanning Electron Micrograph (FESEM), X-Ray Diffraction (XRD) and Fourier Transformed Infrared Spectroscopy (FTIR). The results showed that acid treatment of 5M increased the surface area from 25 m2/g to 75 m2/g and the pore volume increased from 0.1518 cc/g to 0.3546 cc/g. The nanopore size of the clay decreased from 24.8 nm to 19.4 nm after treated with acid. This can be explained due to the elimination of the exchangeable cations and generation of microporosity. The results of XRF showed SiO2 increased from 58.34% to 74.52% and Al2O3 reduced from 34.6% to 18.31%. The mineral oxides such as Fe2O3, MgO, CaO, K2O and TiO2 also reduced. This concluded that H2SO4 treatment has led to significant removal of octahedral Al3+, Fe3+ cations and other impurities. In conclusion, this study showed the physico-chemical properties and morphology of Sayong clay were improved once treated with H2SO4 and therefore suggests better supporting material for enzyme immobilization.

Preparation of β-PbO2 and β-PbO2-MnO2 Coating on Stainless Steel Substrate

2012 ◽  
Vol 490-495 ◽  
pp. 3486-3490
Author(s):  
Qiang Yu ◽  
Zhen Chen ◽  
Zhong Cheng Guo
Keyword(s):  
Stainless Steel ◽  
Mass Fraction ◽  
Stainless Steel Substrate ◽  
Steel Substrate ◽  
Substrate Material ◽  
X Ray Diffraction ◽  
X Ray ◽  
New Type ◽  
Plating Solution ◽  
Element Mass Fraction

In order to prepare a new type of anode material, stainless steel was selected as substrate material. The β-PbO2 coating on stainless steel substrate was prepared under the appropriate plating solution, and the PbO2-MnO2 coating was prepared with thermal decomposition. The crystal structure was determined by X-ray diffraction; Surface morphology was test by Scanning Electron Microscopy; the energy spectrum was used to determine element mass-fraction and the ratio of atomic number of the coatings.

Stacking Faults in a High Nitrogen Face-Centered-Cubic Phase Formed on Nitrogen-Modified Austenitic Stainless Steel

2008 ◽  
Vol 373-374 ◽  
pp. 318-321
Author(s):  
J. Liang ◽  
M.K. Lei
Keyword(s):  
Stainless Steel ◽  
Plasma Source ◽  
Peak Shift ◽  
Cubic Phase ◽  
Face Centered Cubic ◽  
X Ray Diffraction ◽  
High Nitrogen ◽  
X Ray ◽  
Peak Asymmetry ◽  
Face Centered

Effects of stacking faults in a high nitrogen face-centered-cubic phase (γΝ) formed on plasma source ion nitrided 1Cr18Ni9Ti (18-8 type) austenitic stainless steel on peak shift and peak asymmetry of x-ray diffraction were investigated based on Warren’s theory and Wagner’s method, respectively. The peak shift from peak position of the γΝ phase is ascribed to the deformation faults density α, while the peak asymmetry of the γΝ phase is characterized by deviation of the center of gravity of a peak from the peak maximum (Δ C.G.) due to the twin faults density β. The calculated peak positions of x-ray diffraction patterns are consistent with that measured for plasma source ion nitrided 1Cr18Ni9Ti stainless steel.

Hydrothermal Treatment of Coprecipitated YSZ Powders

2010 ◽  
Vol 660-661 ◽  
pp. 983-988 ◽  
Author(s):  
Alexander Rodrigo Arakaki ◽  
Walter Kenji Yoshito ◽  
Valter Ussui ◽  
Dolores Ribeiro Ricci Lazar
Keyword(s):  
Surface Area ◽  
Hydrothermal Treatment ◽  
Gas Adsorption ◽  
X Ray Diffraction ◽  
Electronic Microscopy ◽  
Immersion Method ◽  
Cubic Symmetry ◽  
X Ray ◽  
Granulometric Analysis ◽  
Symmetry Surface

Zirconia stabilized with 8.5 mol% yttria (YSZ) were synthesized by coprecipitation and resulting gels were hydrothermallly treated at 200°C and 220 PSI for 4, 8 and 16 hours. Products were oven dried at 70°C for 24 hours, isostatically pressed as pellets and sintered at 1500 °C for 1 hour. Powders were characterized for surface area with N2 gas adsorption, X-ray diffraction, laser diffraction granulometric analysis and scanning and transmission electronic microscopy. Density of ceramics was measured by an immersion method based on the Archimedes principle. Results showed that powders dried at 70°C are amorphous and after treatment has tetragonal/cubic symmetry. Surface area of powders presented a significant reduction after hydrothermal treatment. Ceramics prepared from hydrothermally treated powders have higher green density but sintered pellets are less dense when compared to that made with powders calcined at 800°C for 1 hour due to the agglomerate state of powders. Solvothermal treatment is a promising procedure to enhance density.

Sign in / Sign up

Export Citation Format

Share Document