Synthesis and performance of a photocatalytic titania-hydroxyapatite composite

2008 ◽  
Vol 23 (9) ◽  
pp. 2398-2405 ◽  
Author(s):  
N. Phonthammachai ◽  
J. Kim ◽  
T.J. White
Keyword(s):  
Calcination Temperature ◽  
X Ray Diffraction ◽  
Titanium Butoxide ◽  
X Ray ◽  
Hydroxyapatite Composite ◽  
Porous Titania ◽  
And Performance ◽  
Optimal Material ◽  
Tricalcium Phosphates ◽  
Thermal Stability Of

The photocatalytic degradation of methylene blue (MB) over a porous titania-hydroxyapatite (HAp) composite under ultraviolet radiation was studied. The catalyst was prepared by coating porous HAp with a titanium butoxide [Ti(OBu)4] sol at titania loadings of 17–49 wt%. Quantitative powder x-ray diffraction showed higher proportions of anatase as the calcination temperature increased from 500 to 800 °C due to crystallization of an amorphous precursor. The transformation of anatase to rutile was delayed until 900 °C, demonstrating the high thermal stability of the composite. Decomposition of HAp to α- and β- tricalcium phosphates takes place at 900 °C and is accompanied by the formation of perovskite at 1000 °C. A systematic study of the influence of calcination temperature and titania:HAp ratios demonstrated that for the optimal material, a surface area of 100 m2 g−1 was obtained at a titania loading of 49 wt% and calcination temperature of 600 °C. A highly dispersed suspension of finely ground titania-HAp enhanced the photodegradation of MB, allowed a high percentage recovery of catalyst, and was shown to be recyclable.

scholarly journals The Effect of Calcination Temperature on the Structure and Performance of Nanocrystalline Mayenite Powders

Materials ◽  
2019 ◽  
Vol 12 (21) ◽  
pp. 3476 ◽  
Author(s):  
Katarzyna Berent ◽  
Sebastian Komarek ◽  
Radosław Lach ◽  
Waldemar Pyda
Keyword(s):  
Thermal Analysis ◽  
Differential Thermal Analysis ◽  
Calcination Temperature ◽  
Phase Formation ◽  
Crystalline Phase ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Appreciable Increase ◽  
And Performance

The effect of calcination temperature on the structural properties and phase formation of synthesized CaO-Al2O3 nanopowder was investigated and discussed. The calcination products were identified by differential thermal analysis (DTA) and the crystalline phase formation was analyzed by X-ray diffraction (XRD). The obtained results showed that the crystallization started at 460 °C. Finally, the microstructures of the nanoparticles were observed by scanning (SEM) and transmission electron (TEM) microscopes. The investigation showed that an increase in the calcination temperature led to the appreciable increase in the crystallite size and the crystallinity of the final product. The obtained data confirmed that the prepared materials were mayenite with different surface area in the range of 71.18 m2/g to 10.34 m2/g after annealing in the temperature range of 470 °C to 960 °C.

The Relative Merits of Oxides of Hafnium, Cerium and Thorium as Surrogates for Plutonium Oxide in Calcium Phosphate Ceramics

2009 ◽  
Vol 1193 ◽  
Author(s):  
B. L. Metcalfe ◽  
S. K. Fong ◽  
L. A. Gerrard ◽  
I. W. Donald ◽  
E. S. Welch ◽  
...  
Keyword(s):  
Calcium Phosphate ◽  
Calcination Temperature ◽  
Cerium Oxide ◽  
Absorption Spectroscopy ◽  
Hafnium Oxide ◽  
Intermediate Level ◽  
X Ray Diffraction ◽  
X Ray ◽  
X Ray Absorption ◽  
Additional Phase

AbstractThe choice of surrogate for plutonium oxide for use during the initial stages of research into the immobilization of intermediate level pyrochemical wastes containing plutonium andamericium oxides in a calcium phosphate host has been investigated by powder X-ray diffraction and X-ray absorption spectroscopy. Two non-radioactive surrogates, hafnium oxide and cerium oxide, together with radioactive thorium oxide were compared. Similarities in behaviour were observed for all three surrogates when calcined at the lowest temperature, 750°C but differences became more pronounced as the calcination temperature was increased to 950°C. Although some reaction occurred between all the surrogates and the host to form a substituted whitlockite phase, increasing the temperature led to a significant increase in the cerium reaction and the formation of an additional phase, monazite. Additionally it was observed that the cerium became increasingly trivalent at higher temperatures.

Formation and Thermal Stability of Nd0.32Y0.68Si1.7 Layers Formed by Channeled Ion Beam Synthesis

1998 ◽  
Vol 514 ◽  
Author(s):  
M. F. Wu ◽  
A. Vantomne ◽  
S. Hogg ◽  
H. Pattyn ◽  
G. Langouche ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Ion Beam ◽  
Hexagonal Structure ◽  
Orthorhombic Structure ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Good Crystalline Quality ◽  
Ion Beam Synthesis ◽  
Thermal Stability Of

ABSTRACTThe Nd-disilicide, which exists only in a tetragonal or an orthorhombic structure, cannot be grown epitaxially on a Si(111) substrate. However, by adding Y and using channeled ion beam synthesis, hexagonal Nd0.32Y0.68Si1.7 epilayers with lattice constant of aepi = 0.3915 nm and cepi = 0.4152 nm and with good crystalline quality (χmin of Nd and Y is 3.5% and 4.3 % respectively) are formed in a Si(111) substrate. This shows that the addition of Y to the Nd-Si system forces the latter into a hexagonal structure. The epilayer is stable up to 950 °C; annealing at 1000 °C results in partial transformation into other phases. The formation, the structure and the thermal stability of this ternary silicide have been studied using Rutherford backscattering/channeling, x-ray diffraction and transmission electron microscopy.

Study of Thermal Behaviour of EPDM/SBR Blends and Carbon Nanocoatings Deposited by Sputtering

2021 ◽  
Vol 875 ◽  
pp. 116-120
Author(s):  
Muhammad Alamgir ◽  
Faizan Ali Ghauri ◽  
Waheed Qamar Khan ◽  
Sajawal Rasheed ◽  
Muhammad Sarfraz Nawaz ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Weight Loss ◽  
Thermogravimetric Analysis ◽  
Thermal Behavior ◽  
Thermal Behaviour ◽  
X Ray Diffraction ◽  
X Ray ◽  
Thermal Stability Of

In this study, the effect of SBR concentration (10 Phr, 20 Phr & 30 Phr ) on the thermal behavior of EPDM/SBR blends was studied. Thermogravimetric analysis (TGA) was used to check weight loss of samples as function of temperature by heating upto 600°C. X-ray diffraction (XRD) was performed to determine quality and % crystallinity of the elastomer blends. It was seen that % crystallinity improved with an increase in the content of SBR in EPDM/SBR blends. TGA revealed that the thermal stability of EPDM/SBR blends has improved by 17% than neat EPDM. Carbon nano-coatings produced by sputtering have no beneficial influence on thermal behaviour of elastomers.

scholarly journals In situ observation of phase changes of a silica-supported cobalt catalyst for the Fischer–Tropsch process by the development of a synchrotron-compatible in situ/operando powder X-ray diffraction cell

2018 ◽  
Vol 25 (6) ◽  
pp. 1673-1682 ◽  
Author(s):  
Adam S. Hoffman ◽  
Joseph A. Singh ◽  
Stacey F. Bent ◽  
Simon R. Bare
Keyword(s):  
High Pressure ◽  
Elevated Pressure ◽  
Phase Changes ◽  
In Situ Observation ◽  
X Ray Diffraction ◽  
Fischer Tropsch ◽  
X Ray ◽  
And Performance ◽  
Co Nanoparticles

In situ characterization of catalysts gives direct insight into the working state of the material. Here, the design and performance characteristics of a universal in situ synchrotron-compatible X-ray diffraction cell capable of operation at high temperature and high pressure, 1373 K, and 35 bar, respectively, are reported. Its performance is demonstrated by characterizing a cobalt-based catalyst used in a prototypical high-pressure catalytic reaction, the Fischer–Tropsch synthesis, using X-ray diffraction. Cobalt nanoparticles supported on silica were studied in situ during Fischer–Tropsch catalysis using syngas, H2 and CO, at 723 K and 20 bar. Post reaction, the Co nanoparticles were carburized at elevated pressure, demonstrating an increased rate of carburization compared with atmospheric studies.

scholarly journals ALUMINA PHASE TRANSFORMATION FROM THERMAL DECOMPOSITION OF AMMONIUM ALUM SYNTHESIZED FROM KANKARA KAOLIN

2017 ◽  
Vol 36 (3) ◽  
pp. 822-828
Author(s):  
SG Bawa ◽  
AS Ahmed ◽  
PC Okonkwo
Keyword(s):  
Thermal Stability ◽  
Phase Transformation ◽  
Calcination Temperature ◽  
Starting Material ◽  
Gamma Alumina ◽  
X Ray ◽  
Alumina Phase ◽  
Ammonium Alum ◽  
Alpha Alumina ◽  
Thermal Stability Of

Thermal stability of transitional alumina phases produced from ammonium alum using Kankara kaolin as starting material was studied. Wet beneficiation method was employed to purify the starting material, after which it was calcined and dealuminated with sulphuric acid. The elemental composition, mineralogical, and physiological analyses were carried out using X-ray fluorescence (XRF), X-ray diffraction (XRD) and Brunauer-Emmett-Teller (BET) techniques respectively. The ammonium alum was thermally treated by varying the calcination temperature from 700 to 1200°C and varying the time of calcination from 1 to 4 h. The formation of gamma alumina began at calcination temperature of 825°C for calcination time of 3 h, which was found to be lower than reported works of 900°C. It was found to be stable at higher temperature of 1125°C, above which phase transformation to alpha alumina was observed. The observed wide range of thermal stability of the gamma alumina phase gives it good advantage to be used for high temperature applications, such as support for catalyst promoters. Alpha alumina phase formation began at 1150°C and was fully formed at 1200°C. BET specific surface area of 166 m2/g was obtained for the gamma alumina phase which was high enough for it application as support for catalyst, catalyst and adsorbent. http://dx.doi.org/10.4314/njt.v36i3.23

Syntheses, Crystal Structures and Thermal Stability of Co(II) and Zn(II) Complexes with Ethyl Carbazate

2005 ◽  
Vol 60 (5) ◽  
pp. 505-510 ◽  
Author(s):  
Tong-Lai Zhang ◽  
Jiang-Chuang Song ◽  
Jian-Guo Zhang ◽  
Gui-Xia Ma ◽  
Kai-Bei Yu
Keyword(s):  
Thermal Stability ◽  
Aqueous Solutions ◽  
Diffraction Analysis ◽  
Single Crystals ◽  
Slow Evaporation ◽  
X Ray Diffraction ◽  
Element Analysis ◽  
Thermal Stabilities ◽  
X Ray ◽  
Thermal Stability Of

Cobalt(II) and zinc(II) complexes of ethyl carbazate (ECZ), [Co(ECZ)3](NO3)2 and [Zn(ECZ)3] (NO3)2, were synthesized. Single crystals of these two compounds were grown from aqueous solutions using a slow evaporation method. Their structures have been determined by X-ray diffraction analysis. Both of them are monoclinic with space group P21/n. The complexes are further characterized by element analysis and IR measurements. Their thermal stabilities are studied by using TG-DTG, DSC techniques. When heated to 350 °C, only metal oxide was left for both complexes.

scholarly journals Structural and thermoelectric properties of the Pr2Zr2O7 compound

2019 ◽  
pp. 4-9
Author(s):  
Adolfo Quiroz-Rodríguez ◽  
Cesia Guarneros-Aguilar ◽  
Ricardo Agustin-Serrano
Keyword(s):  
Electron Microscopy ◽  
Thermal Conductivity ◽  
Thermoelectric Properties ◽  
Crystal Size ◽  
Ambient Pressure ◽  
X Ray Diffraction ◽  
X Ray ◽  
Increasing Temperature ◽  
Thermal Stability Of ◽  
Scanning Electron

In this research, it is presented a detailed study of the structural and thermoelectric properties of the pyrochlore zirconium Pr2Zr2O7 compound prepared by solid-state reaction (SSR) in air at ambient pressure. The synthesized sample was characterized using powder X-ray diffraction. The thermal stability of the thermoelectric compound (TE) Pr2Zr2O7 was tested by thermogravimetric analysis (TGA) and differential thermal analysis (DTA). Scanning electron microscopy shows that the crystal size varies between 0.69 and 2.81μm. Electrical conductivity (\sigma) of the sample calcined at 1400 °C presented values increase irregularly with the increasing temperature from 0.001 to 0.018 S cm-1 as expected in a semiconductor material. The thermal conductivity is lower than 0.44 - 775 W m-1 K-1 which is quite anomalous in comparison with the thermal conductivity of other oxides.

scholarly journals Characterization of the Interface Between the Bulk Glass Forming Alloy Zr41Ti14Cu12Ni10Be23 with Pure Metals and Ceramics

2000 ◽  
Vol 15 (7) ◽  
pp. 1617-1621 ◽  
Author(s):  
Jan Schroers ◽  
Konrad Samwer ◽  
Frigyes Szuecs ◽  
William L. Johnson
Keyword(s):  
Sessile Drop ◽  
Bulk Glass ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Glass Forming ◽  
Processing Times ◽  
Thermal Stability Of

The reaction of the bulk glass forming alloy Zr41Ti14Cu12Ni10Be23 (Vit 1) with W, Ta, Mo, AlN, Al2O3, Si, graphite, and amorphous carbon was investigated. Vit 1 samples were melted and subsequently solidified after different processing times on discs of the different materials. Sessile drop examinations of the macroscopic wetting of Vit 1 on the discs as a function of temperature were carried out in situ with a digital optical camera. The reactions at the interfaces between the Vit 1 sample and the different disc materials were investigated with an electron microprobe. The structure and thermal stability of the processed Vit 1 samples were examined by x-ray diffraction and differential scanning calorimetry. The results are discussed in terms of possible applications for composite materials.

Immobilization of hemoglobin on stable mesoporous multilamellar silica vesicles and their activity and stability

2005 ◽  
Vol 20 (10) ◽  
pp. 2682-2690 ◽  
Author(s):  
Yufang Zhu ◽  
Weihua Shen ◽  
Xiaoping Dong ◽  
Jianlin Shi
Keyword(s):  
Thermal Stability ◽  
Pore Size ◽  
X Ray Diffraction ◽  
X Ray ◽  
Practical Applications ◽  
Silica Material ◽  
Transmission Electron ◽  
Mesoporous Support ◽  
Adsorption Desorption ◽  
Thermal Stability Of

A stable mesoporous multilamellar silica vesicle (MSV) was developed with a gallery pore size of about 14.0 nm. A simulative enzyme, hemoglobin (Hb), was immobilized on this newly developed MSV and a conventional mesoporous silica material SBA-15. The structures and the immobilization of Hb on the mesoporous supports were characterized with x-ray diffraction, transmission electron microscopy, N2 adsorption-desorption isotherms, Fourier transform infrared, ultraviolet-visible spectroscopy, and so forth. MSV is a promising support for immobilizing Hb due to its large pore size and high Hb immobilization capacity (up to 522 mg/g) compared to SBA-15 (236 mg/g). Less than 5% Hb was leached from Hb/MSV at pH 6.0. The activity study indicated that the immobilized Hb retained most peroxidase activity compared to free Hb. Thermal stability of the immobilized Hb was improved by the proctetive environment of MSV and SBA-15. Such an Hb-mesoporous support with high Hb immobilization capacity, high activity, and enhanced thermal stability will be attractive for practical applications.

Sign in / Sign up

Export Citation Format

Share Document