The Evaporative Decomposition of Solutions Method (Eds) for the Production of Ultrafine Y1Ba2Cu3O7 from Nitrate and Mixed Anion Precursor Solutions

1989 ◽  
Vol 169 ◽  
Author(s):  
Rollin E. Lakis ◽  
Sidney R. Butler
Keyword(s):  
Electron Microscopy ◽  
Particle Size ◽  
Barium Carbonate ◽  
Hollow Spheres ◽  
Particle Size Analysis ◽  
Size Analysis ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron

AbstractY1Ba2Cu3O7 has been prepared by the evaporative decomposition of solutions method. Nitrate and mixed anion solutions were atomized and decomposed at temperatures ranging from 300°C to 950°C. The resulting materials have been characterized using x-ray powder diffraction, Thermal Gravimetric Analysis (TGA), particle size analysis, Scanning Electron Microscopy (SEM), and Transmission Electron Microscopy (TEM). The powder consists of 0.3 micron agglomerated hollow spheres with a primary particle size of 0.06 micron. TGA and x-ray diffraction indicate the presence of barium nitrate and barium carbonate due to incomplete decomposition and/or product contamination by the process environment.

Effect of Synthesis Temperature on Particles Size and Morphology of Zirconium Oxide Nanoparticle

2017 ◽  
Vol 50 ◽  
pp. 18-31 ◽  
Author(s):  
Rudzani Sigwadi ◽  
Simon Dhlamini ◽  
Touhami Mokrani ◽  
Patrick Nonjola
Keyword(s):  
Electron Microscopy ◽  
Particle Size ◽  
Zirconium Oxide ◽  
Thermo Gravimetric Analysis ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Crystallite Sizes ◽  
Ft Ir

The paper presents the synthesis and investigation of zirconium oxide (ZrO2) nanoparticles that were synthesised by precipitation method with the effects of the temperatures of reaction on the particles size, morphology, crystallite sizes and stability at high temperature. The reaction temperature effect on the particle size, morphology, crystallite sizes and stabilized a higher temperature (tetragonal and cubic) phases was studied. Thermal decomposition, band structure and functional groups were analyzed by Brunauer-Emmett-Teller (BET), Scanning Electron Microscopy (SEM), Transmission electron microscopy (TEM), X-ray diffraction (XRD), Thermo-gravimetric analysis (TGA) and Fourier transform infrared (FT-IR). The crystal structure was determined using X-ray diffraction. The morphology and the particle size were studied using (SEM) and (TEM). The shaped particles were confirmed through the SEM analysis. The transmission electron microscopic analysis confirmed the formation of the nanoparticles with the particle size. The FT-IR spectra showed the strong presence of ZrO2 nanoparticles.

scholarly journals Mining Wastes of an Albite Deposit as Raw Materials for Vitrified Mullite Ceramics

Minerals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 232
Author(s):  
Pedro J. Sánchez-Soto ◽  
Eduardo Garzón ◽  
Luis Pérez-Villarejo ◽  
George N. Angelopoulos ◽  
Dolores Eliche-Quesada
Keyword(s):  
Particle Size ◽  
Raw Materials ◽  
Phase Evolution ◽  
Particle Size Analysis ◽  
Size Analysis ◽  
Mining Wastes ◽  
X Ray Diffraction ◽  
X Ray ◽  
Maximum Value

In this work, an examination of mining wastes of an albite deposit in south Spain was carried out using X-ray Fluorescence (XRF), X-ray diffraction (XRD), particle size analysis, thermo-dilatometry and Differential Thermal Analysis (DTA) and Thermogravimetric (TG) analysis, followed by the determination of the main ceramic properties. The albite content in two selected samples was high (65–40 wt. %), accompanied by quartz (25–40 wt. %) and other minor minerals identified by XRD, mainly kaolinite, in agreement with the high content of silica and alumina determined by XRF. The content of Na2O was in the range 5.44–3.09 wt. %, being associated with albite. The iron content was very low (<0.75 wt. %). The kaolinite content in the waste was estimated from ~8 to 32 wt. %. The particle size analysis indicated values of 11–31 wt. % of particles <63 µm. The ceramic properties of fired samples (1000–1350 °C) showed progressive shrinkage by the thermal effect, with water absorption and open porosity almost at zero at 1200–1250 °C. At 1200 °C, the bulk density reached a maximum value of 2.38 g/cm3. An abrupt change in the phase evolution by XRD was found from 1150 to 1200 °C, with the disappearance of albite by melting in accordance with the predictions of the phase diagram SiO2-Al2O3-Na2O and the system albite-quartz. These fired materials contained as main crystalline phases quartz and mullite. Quartz was present in the raw samples and mullite was formed by decomposition of kaolinite. The observation of mullite forming needle-shape crystals was revealed by Scanning Electron Microscopy (SEM). The formation of fully densified and vitrified mullite materials by firing treatments was demonstrated.

scholarly journals Enhanced Photocatalytic Activity of Cu2O Cabbage/RGO Nanocomposites under Visible Light Irradiation

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1712
Author(s):  
Appusamy Muthukrishnaraj ◽  
Salma Ahmed Al-Zahrani ◽  
Ahmed Al Otaibi ◽  
Semmedu Selvaraj Kalaivani ◽  
Ayyar Manikandan ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Thermo Gravimetric Analysis ◽  
Visible Region ◽  
Catalytic Performance ◽  
Precipitation Method ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Dye Pollutants ◽  
Transmission Electron

Towards the utilization of Cu2O nanomaterial for the degradation of industrial dye pollutants such as methylene blue and methyl orange, the graphene-incorporated Cu2O nanocomposites (GCC) were developed via a precipitation method. Using Hummers method, the grapheme oxide (GO) was initially synthesized. The varying weight percentages (1–4 wt %) of GO was incorporated along with the precipitation of Cu2O catalyst. Various characterization techniques such as Fourier-transform infra-red (FT-IR), X-ray diffraction (XRD), UV–visible diffused reflectance (UV-DRS), Raman spectroscopy, thermo gravimetric analysis (TGA), energy-dispersive X-ray analysis (EDX), and electro chemical impedance (EIS) were followed for characterization. The cabbage-like morphology of the developed Cu2O and its composites were ascertained from field-emission scanning electron microscopy (FESEM) and high-resolution transmission electron microscopy (HR-TEM). In addition, the growth mechanism was also proposed. The results infer that 2 wt % GO-incorporated Cu2O composites shows the highest value of degradation efficiency (97.9% and 96.1%) for MB and MO at 160 and 220 min, respectively. Further, its catalytic performance over visible region (red shift) was also enhanced to an appreciable extent, when compared with that of other samples.

scholarly journals Synthesis of SnO2 Nanoparticles by High Potential Electrolysis

2017 ◽  
Vol 12 (2) ◽  
pp. 281 ◽  
Author(s):  
Fredy Kurniawan ◽  
Rahmi Rahmi
Keyword(s):  
Particle Size ◽  
Sno2 Nanoparticles ◽  
Particle Size Analysis ◽  
Reaction Engineering ◽  
High Potential ◽  
Size Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Nanoparticles Synthesis ◽  
The Fourier Transform

SnO2 nanoparticles have been synthesized by high voltage electrolysis. Tin bare was used for anode and cathode. The effect of potentials and electrolyte were studied. The particles obtained after electrolysis was characterized using X-ray Diffraction (XRD). The diffractogram is in agreement with the standard diffraction pattern of SnO2 which is identified as tetragonal structure. The Fourier Transform Infrared (FTIR) spectrum indicates that there is a vibration of Sn–O asymmetric at 580 cm-1. The optimum potential for SnO2 nanoparticles synthesis is 60 V at 0.06 M HCl which shows the highest UV-Vis spectrum. The absorption peak of SnO2 nanoparticles by UV-Vis spectrophotometer appears at about 207 nm. The particle size analysis shows that the SnO2 nanoparticles obtained have the size distribution in a range of 25-150 nm with the highest volume at 83.11 nm. Copyright © 2017 BCREC Group. All rights reservedReceived: 15th November 2016; Revised: 26th February 2017; Accepted: 27th February 2017How to Cite: Rahmi, R., Kurniawan, F. (2017). Synthesis of SnO2 Nanoparticles by High Potential Electrolysis. Bulletin of Chemical Reaction Engineering & Catalysis, 12 (2): 281-286 (doi:10.9767/bcrec.12.2.773.281-286)Permalink/DOI: http://dx.doi.org/10.9767/bcrec.12.2.773.281-286 

Structural and Magnetic study of Al3+ doped Ni0.75Zn0.25Fe2-xAlxO4 nanoferrites

2013 ◽  
Vol 1506 ◽  
Author(s):  
L. Wang ◽  
B. K. Rai ◽  
S. R. Mishra
Keyword(s):  
Electron Microscopy ◽  
Particle Size ◽  
Chemical Method ◽  
X Ray Diffraction ◽  
Wet Chemical Method ◽  
X Ray ◽  
Transmission Electron ◽  
Magnetic Dilution ◽  
Wet Chemical ◽  
Structural And Magnetic Properties

AbstractNanostructured Al3+ doped Ni0.75Zn0.25Fe2-xAlxO4 (x = 0.0,0.2,0.4,0.6,0.8, and 1.0) ferrites were synthesized via wet chemical method. X-ray diffraction, transmission electron microscopy, and magnetization measurements have been used to investigate the structural and magnetic properties of spinel ferrites calcined at 950 °C .With the doping of Al3+, the particle size of Ni0.75Zn0.25Fe2-xAlxO4 first increased to 47 nm at x = 0.4 and then decreased down to 37 nm at x = 1. Saturation magnetization decreased linearly with Al3+ due to magnetic dilution. The coercive field showed an inverse dependence on the particle size of ferrites.

scholarly journals Formation of ZnO/Zn0.5Cd0.5Se Alloy Quantum Dots in the Presence of High Oleylamine Contents

Nanomaterials ◽  
2019 ◽  
Vol 9 (7) ◽  
pp. 999
Author(s):  
Yi-An Chen ◽  
Kuo-Hsien Chou ◽  
Yi-Yang Kuo ◽  
Cheng-Ye Wu ◽  
Po-Wen Hsiao ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Quantum Dots ◽  
Particle Size ◽  
X Ray Diffraction ◽  
One Pot ◽  
X Ray ◽  
Transmission Electron ◽  
Average Size ◽  
Alloy Quantum Dots ◽  
First Time

To the best of our knowledge, this report presents, for the first time, the schematic of the possible chemical reaction for a one-pot synthesis of Zn0.5Cd0.5Se alloy quantum dots (QDs) in the presence of low/high oleylamine (OLA) contents. For high OLA contents, high-resolution transmission electron microscopy (HRTEM) results showed that the average size of Zn0.5Cd0.5Se increases significantly from 4 to 9 nm with an increasing OLA content from 4 to 10 mL. First, [Zn(OAc)2]–OLA complex can be formed by a reaction between Zn(OAc)2 and OLA. Then, Fourier transform infrared (FTIR) spectroscopy and X-ray diffraction (XRD) data confirmed that ZnO is formed by thermal decomposition of the [Zn(OAc)2]–OLA complex. The results indicated that ZnO grew on the Zn0.5Cd0.5Se surface, thus increasing the particle size. For low OLA contents, HRTEM images were used to estimate the average sizes of the Zn0.5Cd0.5Se alloy QDs, which were approximately 8, 6, and 4 nm with OLA loadings of 0, 2, and 4 mL, respectively. We found that Zn(OAc)2 and OLA could form a [Zn(OAc)2]–OLA complex, which inhibited the growth of the Zn0.5Cd0.5Se alloy QDs, due to the decreasing reaction between Zn(oleic acid)2 and Se2−, which led to a decrease in particle size.

Phase and Particle Size Analysis of SnO2 Nanomaterials

2015 ◽  
Vol 1109 ◽  
pp. 314-318
Author(s):  
Nor Diyana Abdul Aziz ◽  
Kelimah Elong ◽  
Norlida Kamarulzaman
Keyword(s):  
Particle Size ◽  
Particle Size Analysis ◽  
Annealed Sample ◽  
Degree Of Crystallinity ◽  
Size Analysis ◽  
Size Distributions ◽  
X Ray Diffraction ◽  
Particle Size Distributions ◽  
X Ray ◽  
Particle Sizer

Tin Oxide (SnO2) is a metal oxide which has many applications in industry. In this study, SnO2 powders were synthesized by a self-propagating combustion (SPC) method. The product was annealed at 800 °C for 12 and 24 h before characterizing with X-Ray Diffraction (XRD) for phase studies. X-Ray Diffraction results showed that both samples are pure of tetragonal structure with space group P42/mnm. The sample annealed at a longer period, that is, 24 h, shows a higher degree of crystallinity compared to the 12 h annealed sample. It also shows a smaller full width at half maximum (FWHM), indicating larger crystallite size for the 24 h annealed sample. The particle size analysis reveals that there are two groups of particle size distributions for both samples. SEM results give values that are different from the particle sizer results due to the different nature of the measurement methods.

Particle Size Analysis of the Synthesized Al2O3 by Dissolution and Alkali Fusion-Coprecipitation Methods

2020 ◽  
Vol 860 ◽  
pp. 128-134
Author(s):  
Cahyaning Fajar Kresna Murti ◽  
Malik Anjelh Baqiya ◽  
Endarko ◽  
Triwikantoro
Keyword(s):  
Particle Size ◽  
Ammonium Hydroxide ◽  
Particle Size Analysis ◽  
Fusion Product ◽  
Size Analysis ◽  
Particle Sizes ◽  
X Ray Diffraction ◽  
Bottom Up ◽  
Alkali Fusion ◽  
Transmission Electron

Particle size analysis of synthesized Al2O3 by dissolution and alkali fusion-coprecipitation methods has been conducted. The formation of nano- or microparticles can be synthesized by the top-down (physically) and bottom-up (chemically) methods. In this study, the commercial alumina (Merck) with the particle size of 63 µm was synthesized through the bottom-up method. The dissolution method was done by reacting to alumina with ammonium hydroxide (NH4OH). The alkali fusion method was carried out by reacting alumina with sodium hydroxide (NaOH) and it obtained by coprecipitation of the alkali fusion product with HCl and NH4OH. The result from both methods were calcined at 600°C. The phase of synthesized Al2O3 was identified by using X-ray diffraction (XRD), whereas the morphology observed using a transmission electron microscope (TEM), and the particle sizes measured by particle sizes analyzer (PSA). The XRD pattern shows the γ-Al2O3 phases with particle sizes of ~33 nm and ~25 nm from TEM observations, while the PSA results revealed agglomerated particles with particle sizes of 1263 nm and 477 nm for the dissolution and alkali fusion-coprecipitation method, respectively. Therefore, both methods can be used to reduce the particle size of γ-Al2O3.

A STUDY ON A NEW SYNTHETIC METHOD OF CdS AND CdSe NANOPARTICLES AND THEIR ORGANIC/INORGANIC NANOCOMPOSITE

2002 ◽  
Vol 01 (05n06) ◽  
pp. 501-505 ◽  
Author(s):  
JU YOUNG LEE ◽  
YOUNG SOO KANG ◽  
YONG JOO KIM
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Particle Size ◽  
Cdse Nanoparticles ◽  
Inorganic Nanoparticles ◽  
Synthetic Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Inorganic Films

Materials such as CdS and CdSe inorganic nanoparticles have photoluminescence. Sodium oleate has been used as effective stabilizers for the synthesis of CdS and CdSe nanoparticles in water by autoclave method. Photoluminescence of CdS and CdSe with particle size of 5–14 nm showed λ max at 520 nm and 600 nm, respectively, when were excited at 365 nm. These nanoparticles doped into the PVA resulted in the organic/inorganic films ( PVA/CdS , CdSe ). Photoluminescence, X-ray diffraction and transmission electron microscopy were employed for their characterization.

Sign in / Sign up

Export Citation Format

Share Document