The Performance of Precipitated Calcium Carbonate Fillers in Fine Quality Printing and Writing Papers

1990 ◽  
Vol 197 ◽  
Author(s):  
Robert A. Gill
Keyword(s):  
Particle Size ◽  
Calcium Carbonate ◽  
Surface Area ◽  
Average Particle Size ◽  
Filler Materials ◽  
Average Particle ◽  
Strong Correlations ◽  
Precipitated Calcium Carbonate ◽  
Paper Properties ◽  
Custom Made

ABSTRACTThe trend toward alkaline papermaking has accelerated over the past four years due to the availability of inexpensive, high quality precipitated calcium carbonate. This movement has been largely brought about through on-site production of precipitated calcium carbonate (PCC). Over ten facilities exist in North America providing the host mills with custom-made PCC products to provide specific properties for the paper grades being manufactured.Laboratory studies were recently conducted to investigate the performance of paper-grade PCC fillers in fine quality printing papers. This investigation focused on the effect of changes in PCC particle size, size distribution, surface area, and morphology on paper properties. The PCC fillers were also compared to other filler materials such as ground limestone and kaolin.In general, the results show that sheet properties are greatly influenced by the size and shape of the PCC product used. The data reveal strong correlations between average particle size and/or surface area, and sheet properties such as opacity, porosity, tensile strength, bulk, and sizing within certain filler morphologies.

Characterization of Precipitated Calcium Carbonate from Eggshell Powder

2011 ◽  
Vol 410 ◽  
pp. 228-231
Author(s):  
Wimonlak Sutapun ◽  
Yupaporn Ruksakulpiwat ◽  
Nitinat Suppakarn ◽  
Rachasit Jeencham ◽  
Ajcharaporn Aontee
Keyword(s):  
Particle Size ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Average Particle Size ◽  
Spherical Shape ◽  
Average Diameter ◽  
Single Step ◽  
Average Particle ◽  
Precipitated Calcium Carbonate

In this work, PCC was prepared from chicken eggshell powder (ESP) by dissolving 100 g ESP in 1 M hydrochloric acid at room temperature. Under vigorous stirring, PCC was precipitated from the ESP-dissolved solution using 1 M sodium carbonate solution. The dried PESP (precipitated eggshell powder) was then characterized by particle size analyzer, X-ray diffractometer, Brunauer-Emmett-Teller surface analyzer and thermogravimetric analyzer. The particle shape of the PESP was revealed using scanning electron microscope. It was found that PESP was a binary mixer of calcite and vaterite. The particles were in cubic and spherical shape. In addition, PESP had a volume average diameter of 8.16 μm, D[V, 0.5] of 7.22 μm, D[V,0.9] of 16.57 μm, and the specific surface area of 4.38 m2/g. The average particle size was lower than and the specific surface area was higher than that of ESP. The decomposition process of PESP occured in a single step between 610 and 770 °C, with 44.43% weight loss.

scholarly journals Reactivity of calcium carbonate prepared from flue gas desulfurization gypsum

2019 ◽  
Vol 12 (1) ◽  
pp. 14-21
Author(s):  
Jana Jurišová ◽  
Vladimír Danielik ◽  
Pavel Fellner ◽  
Milan Králik ◽  
Tomáš Foltinovič
Keyword(s):  
Particle Size ◽  
Calcium Carbonate ◽  
Flue Gas ◽  
Average Particle Size ◽  
Initial Reaction Rate ◽  
Flue Gas Desulfurization ◽  
Initial Reaction ◽  
Average Particle ◽  
Precipitated Calcium Carbonate ◽  
Compact Structure

Abstract Reactivity of various calcium carbonate samples for flue gas desulfurization was tested. Two groups of CaCO3 samples were considered; natural limestone containing calcite phase dominantly and samples prepared by the conversion of gypsum with ammonium and carbon dioxide (precipitated CaCO3) containing different amounts of calcite, aragonite and vaterite. Reactivity of precipitated calcium carbonate depends primarily on the particle size, similarly as in case of industrial samples. The initial reaction rate was comparable with the industrial limestones for samples with the average particle size lower than 15 μm. However, the conversion of laboratory samples was significantly higher after 5 min of the reaction. Phase composition of the precipitated calcium carbonate has a minor but noticeable impact on the reactivity. The presence of vaterite slightly increased the reactivity, which is in accordance with its lower compact structure in comparison with calcite and aragonite. Unexpected effect of the increased content of aragonite, which is the most compact phase in comparison with calcite and vaterite, was observed. If calcium carbonate contains up to approximately 30 % of aragonite the reactivity increases, which can be explained by the SEM pictures showing agglomerate composition with relatively high specific surface. At higher contents of aragonite, the reactivity decreases. All the obtained results proved the suitability of precipitated CaCO3 prepared from flue gas desulfurization gypsum to be recycled in the flue gas desulfurization process.

Morphology-Controlled CaCO3 Nanostructures by Modified Co-Precipitation in Pulsed Mode

2015 ◽  
Vol 752-753 ◽  
pp. 148-153
Author(s):  
M.M. Nassar ◽  
Taha Ebrahiem Farrag ◽  
M.S. Mahmoud ◽  
Sayed Abdelmonem
Keyword(s):  
Particle Size ◽  
Calcium Carbonate ◽  
Rotation Speed ◽  
Average Particle Size ◽  
Calcium Nitrate ◽  
Precipitation Method ◽  
Average Particle ◽  
X Ray ◽  
Co Precipitation ◽  
Pulsed Mixing

Calcium carbonate nanoparticles and nanorods were synthesized by precipitation from saturated sodium carbonate and calcium nitrate aqueous solutions through co precipitation method. A new rout of synthesis was done by both using pulsed mixing method and controlling the addition of calcium nitrate. The effect of the agitation speed, and the temperature on particle size and morphology were investigated. Particles were characterized using X-ray Microanalysis, X-ray analysis (XRD) and scanning electron microscopy (SEM). The results indicated that increasing the mixer rotation speed from 3425 to 15900 (rpm) decreases the average particle size to 64±7 nm. A rapid nucleation then aggregation induced by excessive shear force phenomena could explain this observation. Moreover, by increasing the reaction temperature, the products were converted from nanoparticle to nanorods. The maximum attainable aspect ratio was 6.23 at temperature of 75°C and rotation speed of 3425. Generally, temperature raise promoted a significant homoepitaxial growth in one direction toward the formation of calcite nanorods. Overall, this study can open new avenues to control the morphology of the calcium carbonate nanostructures.

scholarly journals Microwave solvothermal synthesis and characterization of manganese-doped ZnO nanoparticles

2016 ◽  
Vol 7 ◽  
pp. 721-732 ◽  
Author(s):  
Jacek Wojnarowicz ◽  
Roman Mukhovskyi ◽  
Elzbieta Pietrzykowska ◽  
Sylwia Kusnieruk ◽  
Jan Mizeracki ◽  
...  
Keyword(s):  
Particle Size ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Solvothermal Synthesis ◽  
Web Application ◽  
Zinc Acetate Dihydrate ◽  
Average Particle Size ◽  
Average Particle ◽  
Sem Images

Mn-doped zinc oxide nanoparticles were prepared by using the microwave solvothermal synthesis (MSS) technique. The nanoparticles were produced from a solution of zinc acetate dihydrate and manganese(II) acetate tetrahydrate using ethylene glycol as solvent. The content of Mn2+ in Zn1− x Mn x O ranged from 1 to 25 mol %. The following properties of the nanostructures were investigated: skeleton density, specific surface area (SSA), phase purity (XRD), lattice parameters, dopant content, average particle size, crystallite size distribution, morphology. The average particle size of Zn1− x Mn x O was determined using Scherrer’s formula, the Nanopowder XRD Processor Demo web application and by converting the specific surface area results. X-ray diffraction of synthesized samples shows a single-phase wurtzite crystal structure of ZnO without any indication of additional phases. Spherical Zn1− x Mn x O particles were obtained with monocrystalline structure and average particle sizes from 17 to 30 nm depending on the content of dopant. SEM images showed an impact of the dopant concentration on the morphology of the nanoparticles.

Preparation and Particle Size Characterization of Cu Nanoparticles Prepared by Anodic Arc Plasma

2010 ◽  
Vol 92 ◽  
pp. 163-169
Author(s):  
Hong Xia Qiao ◽  
Zhi Qiang Wei ◽  
Ming Ru Zhou ◽  
Zhong Mao He
Keyword(s):  
Crystal Structure ◽  
Particle Size ◽  
Specific Surface ◽  
Size Distribution ◽  
Surface Area ◽  
Specific Surface Area ◽  
Average Particle Size ◽  
Spherical Shape ◽  
Average Particle ◽  
Uniform Size

Copper nanoparticles were successfully prepared in large scales by means of anodic arc discharging plasma method in inert atmosphere. The particle size, specific surface area, crystal structure and morphology of the samples were characterized by X-ray diffraction (XRD), BET equation, transmission electron microscopy (TEM) and the corresponding selected area electron diffraction (SAED). The experiment results indicate that the crystal structure of the samples is fcc structure as same as that of the bulk materials. The specific surface area is is 11 m2/g, with the particle size distribution ranging from 30 to 90 nm, the average particle size about 67nm obtained from TEM and confirmed from XRD and BET results. The nanoparticles have uniform size, higher purity, narrow size distribution and spherical shape can be prepared by this convenient and effective method.

scholarly journals Growth of significantly low dimensional zinc orthotitanate (Zn2TiO4) nanoparticles by solid state reaction method

2018 ◽  
Vol 50 (1) ◽  
pp. 133-138 ◽  
Author(s):  
Lizina Khatua ◽  
Rudrashish Panda ◽  
Avanendra Singh ◽  
Arpan Nayak ◽  
Pravakar Satapathy ◽  
...  
Keyword(s):  
Particle Size ◽  
Solid State ◽  
Surface Area ◽  
Solid State Reaction ◽  
Average Particle Size ◽  
Cost Effective ◽  
Solid State Reaction Method ◽  
Average Particle ◽  
Reaction Method ◽  
Low Dimensional

In this work, the ZnO-TiO2 mixed phase nanoparticles were prepared by solid state reaction method by using ZnO and TiO2 powder as precursors. The X-ray diffraction pattern shows a dominant phase of Zinc Orthotitanate (Zn2TiO4). The average particle size (58?18 nm) calculated by the analysing FESEM data closely matches with the particle size calculated by Scherrer?s equation. The calculated average particle size is significantly smaller than the previously published results of nanoparticles, prepared by same method. In the Brunauer-Emmett-Teller (BET) study the specific surface area of the nanoparticles was found as 8.78 m2/g which is similar to the surface area reported in this material prepared by mechanochemical method. The method which we report is simpler and cost effective unlike the previous reported.

Development of Heterostructured Ferroelectric SrZrO3/CdS Photocatalysts with Enhanced Surface Area and Photocatalytic Activity

2020 ◽  
Vol 20 (6) ◽  
pp. 3770-3779 ◽  
Author(s):  
Umar Farooq ◽  
Farheen Naz ◽  
Ruby Phul ◽  
Nayeem Ahmad Pandit ◽  
Sapan Kumar Jain ◽  
...  
Keyword(s):  
Particle Size ◽  
Dielectric Constant ◽  
Photocatalytic Activity ◽  
Surface Area ◽  
Room Temperature ◽  
Average Particle Size ◽  
Chemical Deposition ◽  
Bet Surface Area ◽  
Cds Nanoparticles ◽  
Average Particle

This paper reports the attempt to develop an efficient heterostructure photocatalyst by employing SrZrO3 as ferroelectric substrate with deposited nanostructured CdS semiconductor on the surface. Primarily bare SrZrO3 and CdS nanoparticles were synthesized by using polymeric citrate precursor and co-precipitation routes, respectively. The chemical deposition technique was used to develop the CdS over the surface of the pre-synthesized SrZrO3 nanoparticles. The synthesized bare nanoparticles and their heterostructure were characterized by XRD which shows the formation of orthorhombic and face centred cubic (FCC) phases of SrZrO3 and CdS, respectively. TEM was used to estimate the morphology and particle size of as-synthesized nanoparticles, which shows the average particle size of 14, 24 and 25 nm for SrZrO3, CdS and SrZrO3/CdS, respectively. The BET surface area of SrZrO3, CdS and SrZrO3/CdS samples was found to be 299, 304 and 312 m2/g respectively. Methylene blue was used as model pollutant to determine the photocatalytic activity of the synthesized nanomaterials. The heterostructure shows an enhanced activity as compared to bare nanoparticles. Dielectric constant and dielectric loss of the nanoparticles was investigated as a function of frequency at room temperature and as a function of temperature at 500 kHz. The room temperature dielectric constant for SrZrO3, CdS and SrZrO3/CdS was found to be 13.2, 17.8 and 25.5 respectively at 100 kHz.

scholarly journals Preparation and Characterization of NiO Nanoparticles by Anodic Arc Plasma Method

2009 ◽  
Vol 2009 ◽  
pp. 1-5 ◽  
Author(s):  
Hongxia Qiao ◽  
Zhiqiang Wei ◽  
Hua Yang ◽  
Lin Zhu ◽  
Xiaoyan Yan
Keyword(s):  
Particle Size ◽  
Particle Size Distribution ◽  
Specific Surface ◽  
Size Distribution ◽  
Surface Area ◽  
Specific Surface Area ◽  
Average Particle Size ◽  
Average Particle ◽  
Arc Plasma ◽  
Nio Nanoparticles

NiO nanoparticles with average particle size of 25 nm were successfully prepared by anodic arc plasma method. The composition, morphology, crystal microstructure, specific surface area, infrared spectra, and particle size distribution of product were analyzed by using X-ray diffraction (XRD), transmission electron microscopy (TEM) and the corresponding selected area electron diffraction (SAED), Fourier transform infrared (FTIR) spectrum, and Brunauer-Emmett-Teller (BET)N2adsorption. The experiment results show that the NiO nanoparticles are bcc structure with spherical shape and well dispersed, the particle size distribution ranging from 15 to 45 nm with the average particle size is about 25 nm, and the specific surface area is 33 m2/g. The infrared absorption band of NiO nanoparticles shows blue shifts compared with that of bulk NiO.

scholarly journals The Characterization of Heterogeneous Nanocatalyst of Biohydroxyapatite-Lithium and its Application for Converting Malapari Seed Oil (Milletia pinnata L.) to Biodiesel

2018 ◽  
Vol 34 (4) ◽  
pp. 1817-1823
Author(s):  
I. Nengah Simpen ◽  
I. Made Sutha Negara ◽  
Ni Made Puspawati
Keyword(s):  
Particle Size ◽  
Surface Area ◽  
Seed Oil ◽  
Surface Acidity ◽  
Average Particle Size ◽  
Bet Surface Area ◽  
Average Particle ◽  
Bovine Bone ◽  
Heterogeneous Nanocatalyst ◽  
Surface Basicity

Heterogeneous nanocatalyst of biohydroxyapatite-lithium (HA-Li) has been prepared through modification of HA extracted from bovine bone waste with Li at various calcination temperatures (400-700oC). Characterizations of the heterogeneous catalysts were including surface acidity-basicity, functional groups, BET surface area, particle size, and surface morphology. Optimization of catalyst ratios (1-7%) with the best characterization was applied for converting Malapari seed oil (Milletia pinnata L.) to biodiesel. The characterization results showed that HA-Li catalyst calcinated at 600oChad the highest surface basicity and Lewis acid sites revealing specific functional group of O-Li at wavenumber of 1612.49 cm-1. BET surface area of HA-Li catalyst decreased with increased average particle size. SEM analysis suggested that morfology of catalysts formed stack of agglomerates. The highest yield of biodiesel obtained on a catalyst ratio of 5% was 88.16%. GC-MS analysis showed 10 peaks, and 5 of the peaks exhibiting the highest percentage area were identified as methyl oleic, methyl palmitic, methyl erusic, methyl stearic, and methyl linoleic.

Development of the Process of Pseudo-Ligatures Manufacturing from Aluminum and Nickel Powders for the Modification of Alloys

2014 ◽  
Vol 698 ◽  
pp. 452-456 ◽  
Author(s):  
Ekaterina A. Nosova ◽  
Antonina A. Kuzina ◽  
Anna V. Kuts
Keyword(s):  
Particle Size ◽  
Specific Surface ◽  
Surface Area ◽  
Melting Temperature ◽  
Specific Surface Area ◽  
Aluminum Powder ◽  
Nickel Powder ◽  
Average Particle Size ◽  
Average Particle ◽  
Powder Sintering

Compacting after pressing and sintering of briquettes made from an aluminum powder with an average particle size from 50 to 150 microns, the specific surface area Ssp=0.26 m2/g and a nickel powder with an average particle size from 25 to 100 microns, the specific surface area Ssp= 0.03 m2/g has been investigated. Pressing load varied from 15 to 25 MPa for the aluminum powder and from 20 to 45 MPa for the nickel powder. Sintering of aluminum powder briquettes was carried out at temperatures (0.5-0.83) of melting temperature, (0.3-0.46) of melting temperature from the nickel powder. It is shown that the application of high pressure, low temperatures and short time makes it possible to receive pseudo-ligatures from an aluminum powder with porosity about 32% and a nickel powder with porosity about 30%.

Sign in / Sign up

Export Citation Format

Share Document