Effect of Cooling Rate on the Structure of Rapidly Cooled Fe75Si15 B10

1983 ◽  
Vol 28 ◽  
Author(s):  
John L. Walter ◽  
Ami E. Berkowitz
Keyword(s):  
Cooling Rate ◽  
Melt Spinning ◽  
Structural Characteristics ◽  
Rapid Quenching ◽  
Metal Alloys ◽  
X Ray Diffraction ◽  
X Ray ◽  
Spark Erosion ◽  
Water Atomization ◽  
Solidification Of Metal

Solidification of metal alloys by rapid quenching can result in the formation of amorphous or microcrystalline solids, or materials with improved microstructural homogeneity, all with the view of forming new phases or obtaining improved properties. Some alloys may be cooled at high rates to achieve “microcrystallinity” but cannot be cooled rapidly enough to become amorphous. Other alloys may achieve both conditions depending on the cooling rate. We have examined the effects of cooling rate on the structure of one alloy that can, depending on the cooling rate, be made partially or completely amorphous. The alloy is Fe75Si15B10 (atom percent) which was formed as ribbon by melt spinning and as powder by spark erosion in dielectrics of different cooling characteristics and by gas-water atomization. The structural characteristics were determined by x-ray diffraction, measurements of magnetic properties and by optical and scanning electron microscopy.

Structure, Magnetic Properties and Hyperfine Parameters of Nd-Substituted Ni-Fe-Ga Heusler Alloys

MRS Advances ◽  
2017 ◽  
Vol 2 (25) ◽  
pp. 1341-1346
Author(s):  
Monica Sorescu ◽  
Felicia Tolea ◽  
Mihaela Valeanu ◽  
Mihaela Sofronie
Keyword(s):  
Melt Spinning ◽  
Magnetic Measurements ◽  
Heusler Alloys ◽  
Hyperfine Magnetic Field ◽  
Rapid Quenching ◽  
Linear Least Squares ◽  
X Ray Diffraction ◽  
Hyperfine Parameters ◽  
X Ray ◽  
Field Distributions

ABSTRACTSamples of Ni57-xNdxFe18Ga25 with x=2 and 4 were prepared in ribbon form by rapid quenching via melt spinning route. The samples were analyzed by X-ray diffraction (XRD), magnetic measurements and Mössbauer spectroscopy, both in the as-quenched form and after thermal annealing at 900 oC for 2 min and 400 °C for 2 hours. For x=2 the Nd atoms are completely dissolved in the Ni-Fe-Ga matrix, while for x=4 the additional occurrence of the secondary 2:17 phase could be resolved. These findings were supported by the analysis of hyperfine magnetic field distributions obtained from the non-linear least-squares fitting of the Mössbauer spectra.

Influence of Solidification Speed on Quality and Quantity of Structural Defects in Fe61Co10Zr2.5Hf2.5Y2W2B20 Amorphous Alloy

2010 ◽  
Vol 654-656 ◽  
pp. 1074-1077 ◽  
Author(s):  
Marcin Nabiałek ◽  
Marcin Dośpiał ◽  
Michał Szota ◽  
Paweł Pietrusiewicz
Keyword(s):  
Amorphous Alloy ◽  
Cooling Rate ◽  
Melt Spinning ◽  
Structural Defects ◽  
Strongly Correlated ◽  
X Ray Diffraction ◽  
Linear Type ◽  
X Ray ◽  
Solidification Speed ◽  
Point Type

The microstructure of Fe61Co10Zr2,5Hf2,5Nb2W2B20 amorphous alloy in the form of ribbons obtained by classical melt spinning and plates obtained by an induction suction method were investigated using X-ray diffraction. The type of structural defects were studied by analysis of the magnetization characteristics near ferromagnetic saturation of the sample. It was shown that the presence of structural defects is strongly correlated with sample thickness and production process. It was shown that ribbons with cooling rate between 105-106 K/s have point type defects, wires obtained with lower cooling rate between 101-102 K/s, have linear type defect (quasi-dislocation dipoles). crystallization.

Effect of Cooling Rate on Microstructure and Mechanical Property of Fe-6.5wt%Si Alloy

2016 ◽  
Vol 850 ◽  
pp. 571-574
Author(s):  
Jing Ye Jiao ◽  
Qi Zhao Shen ◽  
Ai Chao Cheng ◽  
Ren Fei Guo ◽  
Tie Tao Zhou
Keyword(s):  
Cooling Rate ◽  
Silicon Content ◽  
Melt Spinning ◽  
Laser Surface ◽  
Gas Atomization ◽  
Micro Hardness ◽  
X Ray Diffraction ◽  
X Ray ◽  
Laser Surface Remelting ◽  
Microstructure And Mechanical Property

Due to its high silicon content, Fe-6.5wt%Si alloy has low iron loss and its magnetostriction is almost zero. And therefore Fe-6.5wt%Si alloy has good development prospect. However it has poor ambient temperature ductility and its cold rolling is very difficult. It’s important to study the effect of cooling rate on the microstructure and mechanical properties of Fe-6.5wt%Si alloy. In the present study the master alloy was melted and cooled through normalization, gas atomization, laser surface remelting and melt spinning. The microstructure, micro-hardness and X-ray diffraction were analyzed. The evolution of the microstructure at different cooling rate was summarized. The results indicated that under high cooling rate, the grain was obviously refined, and the microhardness decreased, but the change of phase was not obvious.

Effect of Cooling Rate on the Transformation Temperatures of Ni50Ti36Hf14 Melt-Spun Ribbons

2018 ◽  
Vol 930 ◽  
pp. 345-348
Author(s):  
R.L. Soares ◽  
Walman Benicio Castro
Keyword(s):  
Differential Scanning Calorimetry ◽  
Martensitic Transformation ◽  
Cooling Rate ◽  
Melt Spinning ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Melt Spun ◽  
Melt Spun Ribbons ◽  
Memory Characteristics

Solidification structures and shape memory characteristics of Ni50Ti36Hf14(at.%) alloy ribbons prepared by melt spinning were investigated by means of differential scanning calorimetry and X-ray diffraction. In these experiments particular attention has been paid to change the velocity of cooling wheel from 20 to 40 m/s. Then the cooling rates of ribbons were controlled. The effect of this cooling rate on solidification structures and martensitic transformation behaviors is discussed. When the ribbon is produced at a wheel velocity of 40 m/s in melt spinning, the degree of supercooling becomes high because of its thinner thickness.

A High Resolution Study of G.P. Zones in Aluminum - 4.2 at % Silver

1982 ◽  
Vol 40 ◽  
pp. 722-723 ◽  
Author(s):  
R. Gronsky
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
High Resolution ◽  
Computer Simulations ◽  
Structural Characteristics ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Resolution Study

The phenomenon of clustering in Al-Ag alloys has been extensively studied since the early work of Guinierl, wherein the pre-precipitation state was characterized as an assembly of spherical, ordered, silver-rich G.P. zones. Subsequent x-ray and TEM investigations yielded results in general agreement with this model. However, serious discrepancies were later revealed by the detailed x-ray diffraction - based computer simulations of Gragg and Cohen, i.e., the silver-rich clusters were instead octahedral in shape and fully disordered, atleast below 170°C. The object of the present investigation is to examine directly the structural characteristics of G.P. zones in Al-Ag by high resolution transmission electron microscopy.

scholarly journals Mechanochemical Preparation of Slow Release Fertilizer Based on Glauconite–Urea Complexes

Minerals ◽  
2019 ◽  
Vol 9 (9) ◽  
pp. 507 ◽  
Author(s):  
Maxim Rudmin ◽  
Elshan Abdullayev ◽  
Alexey Ruban ◽  
Ales Buyakov ◽  
Bulat Soktoev
Keyword(s):  
Milling Time ◽  
Slow Release ◽  
Mechanochemical Activation ◽  
Structural Characteristics ◽  
Fluorescence Analysis ◽  
Planetary Mill ◽  
X Ray Diffraction ◽  
Mechanochemical Method ◽  
X Ray ◽  
Slow Release Fertilizers

We investigated the mechanochemical synthesis of complex slow release fertilizers (SRF) derived from glauconite. We studied the effectiveness of the mechanical intercalation of urea into glauconite using planetary and ring mills. The potassium-nitric complex SRFs were synthesized via a mechanochemical method mixing glauconite with urea in a 3:1 ratio. The obtained composites were analyzed using X-ray diffraction analysis, scanning electron microscopy, X-ray fluorescence analysis, and infrared spectroscopy. The results show that as duration of mechanochemical activation increases, the mineralogical, chemical, and structural characteristics of composites change. Essential modifications associated with a decrease in absorbed urea and the formation of microcrystallites were observed when the planetary milling time increased from 5 to 10 min and the ring milling from 15 to 30 min. Complete intercalation of urea into glauconite was achieved by 20 min grinding in a planetary mill or 60 min in a ring mill. Urea intercalation in glauconite occurs much faster when using a planetary mill compared to a ring mill.

Nanostructured TiO2-Based Composites for Light Absorption

2014 ◽  
Vol 975 ◽  
pp. 207-212
Author(s):  
Dayse I. dos Santos ◽  
Olayr Modesto Jr. ◽  
Luis Vicente A. Scalvi ◽  
Americo S. Tabata
Keyword(s):  
Metal Oxide ◽  
Light Absorption ◽  
Structural Characteristics ◽  
Sol Gel ◽  
Second Phase ◽  
X Ray Diffraction ◽  
Two Phase ◽  
X Ray ◽  
Oxide Powders

Metal oxide nanocomposites were prepared by two different routes: polyol and sol-gel. Characterization by X ray diffraction showed that the first process produces directly a two-phase material, while the sol-gel powder never showed second phase below 600°C. Light spectroscopy of the treated powders indicated similarities for the processed materials. Although the overall material compositions are about the same, different structural characteristics are found for each processing. With the exception of Ti-Zn materials, all the double metal oxide powders showed higher absorbance than either TiO2 powder.

The high-pressure cadmium borate Cd6B22O39·H2O

2015 ◽  
Vol 70 (3) ◽  
pp. 183-190 ◽  
Author(s):  
Gerhard Sohr ◽  
Nina Ciaghi ◽  
Klaus Wurst ◽  
Hubert Huppertz
Keyword(s):  
High Pressure ◽  
High Temperature ◽  
Structural Characteristics ◽  
X Ray Diffraction ◽  
X Ray ◽  
High Pressure High Temperature ◽  
Cell Dimensions ◽  
Temperature Experiment ◽  
Unit Cell Dimensions ◽  
Ir And Raman

AbstractSingle crystals of the hydrous cadmium borate Cd6B22O39·H2O were obtained through a high-pressure/high-temperature experiment at 4.7 GPa and 1000 °C using a Walker-type multianvil apparatus. CdO and partially hydrolyzed B2O3 were used as starting materials. A single crystal X-ray diffraction study has revealed that the structure of Cd6B22O39·H2O is similar to that of the type M6B22O39·H2O (M=Fe, Co). Layers of corner-sharing BO4 groups are interconnected by BO3 groups to form channels containing the metal cations, which are six- and eight-fold coordinated by oxygen atoms. The compound crystallizes in the space group Pnma (no. 62) [R1=0.0379, wR2=0.0552 (all data)] with the unit cell dimensions a=1837.79(5), b=777.92(2), c=819.08(3) pm, and V=1171.00(6) Å3. The IR and Raman spectra reflect the structural characteristics of Cd6B22O39·H2O.

Phase Formation in FeOx-SiO2-Cu2O-ZnO-FeS System during Melts Crystallization

2010 ◽  
Vol 297-301 ◽  
pp. 602-607
Author(s):  
Evgeny N. Selivanov ◽  
R.I. Gulyaeva ◽  
N.I. Selmenskich
Keyword(s):  
Cooling Rate ◽  
Phase Formation ◽  
X Ray Diffraction ◽  
X Ray ◽  
Two Samples ◽  
And Calorimetry

The phase formation in oxide-sulphidic systems was studied with the use of X-ray diffraction, mineralography, combined thermogravimetry and calorimetry, in addition to Х-ray spectral microanalysis. The purpose of this work was to estimate the effect of cooling rate of melts in FeOx-SiO2-Cu2O-ZnO-FeS systems on structure and content of the resulting phases. Test subjects were two samples having following compositions (wt. %): I - 40.5 Fe, 2.41 S, 0.87 Cu, 3.87 Zn, 32.1 SiO2 and II - 40.7 Fe, 3.05 S, 8.55 Cu, 4.1 Zn and 19.5 SiO2. Cooling rate of the melts was changed from 0.3 up to 900оС/s.

Sign in / Sign up

Export Citation Format

Share Document