Silicon on Insulator by High Dose Implantation

1984 ◽  
Vol 33 ◽  
Author(s):  
P. L. F. Hemment
Keyword(s):  
Physical Properties ◽  
Thermal Processing ◽  
Vlsi Circuits ◽  
Silicon On Insulator ◽  
High Dose ◽  
High Current ◽  
Processing Technologies ◽  
Oxygen Ions ◽  
High Doses ◽  
High Dose Implantation

ABSTRACTSilicon on insulator structures consisting of a buried dielectric, formed by the implantation of high doses of oxygen ions, have been shown to be suitable substrates for LSI circuits. The substrates are compatible with present silicon processing technologies and are confidently expected to be suitable for VLSI circuits. In this paper the microstructure and physical properties of this SOI material will be described and the dependence of these characteristics upon the implantation conditions and subsequent thermal processing will be discussed. With this information, it is then possible to outline the specification for a high current oxygen implanter.

Defect reduction in oxygen implanted silicon-on-insulator material during high-temperature annealing

1989 ◽  
Vol 47 ◽  
pp. 604-605
Author(s):  
P. Roitman ◽  
B. Cordts ◽  
S. Visitserngtrakul ◽  
S.J. Krause
Keyword(s):  
High Temperature ◽  
Annealing Temperature ◽  
Silicon On Insulator ◽  
High Dose ◽  
High Temperature Annealing ◽  
High Current ◽  
Defect Reduction ◽  
Annealing Step ◽  
Multiple Cycle ◽  
Defect Densities

Synthesis of a thin, buried dielectric layer to form a silicon-on-insulator (SOI) material by high dose oxygen implantation (SIMOX – Separation by IMplanted Oxygen) is becoming an important technology due to the advent of high current (200 mA) oxygen implanters. Recently, reductions in defect densities from 109 cm−2 down to 107 cm−2 or less have been reported. They were achieved with a final high temperature annealing step (1300°C – 1400°C) in conjunction with: a) high temperature implantation or; b) channeling implantation or; c) multiple cycle implantation. However, the processes and conditions for reduction and elimination of precipitates and defects during high temperature annealing are not well understood. In this work we have studied the effect of annealing temperature on defect and precipitate reduction for SIMOX samples which were processed first with high temperature, high current implantation followed by high temperature annealing.

An Electrical Characterization of Sol Films Using Devices Formed by Oxygen Implant and Rapid Thermal Processing

1987 ◽  
Vol 92 ◽  
Author(s):  
Jim D. Whitfield ◽  
Marie E. Burnham ◽  
Charles J. Varker ◽  
Syd.R. Wilson
Keyword(s):  
Thermal Processing ◽  
Rapid Thermal Processing ◽  
High Energy ◽  
Thermally Grown Oxide ◽  
Silicon On Insulator ◽  
Wafer Surface ◽  
High Dose ◽  
Active Device ◽  
Insulating Layer ◽  
Oxygen Implantation

The advantages of Silicon-on-Insulator (SO) devices over bulk Silicon devices are well known (speed, radiation hardened, packing density, latch up free CMOS,). In recent years, much effort has been made to form a thin, buried insulating layer just below the active device region. Several approaches are being developed to fabricate such a buried insulating layer. One viable approach is by high dose, high energy oxygen implantation directly into the silicon wafer surface (1-3). With proper implant and annealing conditions, a thin stoichiometric buried oxide with a good crystalline quality silicon overlayer can be formed on which an epitaxial layer can be grown and functional devices and circuits built. As SO1 circuits become market viable, mass production tools and techniques are being developed and evaluated. Of particular interest here is the evaluation of high current oxygen implantation with rapid thermal processing on the electrical characteristics of the oxide-silicon interfaces, the silicon overlayer and the thermally grown oxide on the top surface using measurements on gated diodes and guarded capacitors.

Formation of Buried Sio2 By High Dose Implantation of Oxygen at Room and Liquid Nitroeen Temperatures

1985 ◽  
Vol 53 ◽  
Author(s):  
F. Namavar ◽  
J. I. Budnick ◽  
F. H. Sanchez ◽  
H. C. Hayden
Keyword(s):  
Liquid Nitrogen ◽  
Current Density ◽  
Room Temperature ◽  
Rutherford Backscattering ◽  
High Dose ◽  
Crystalline Quartz ◽  
Oxygen Ions ◽  
High Dose Implantation ◽  
A Current

ABSTRACTWe have carried out a study to understand the mechanisms involved in the formation of buried SIO2 by high dose implantation of oxygen into Si targets. Oxygen ions were implanted at 150 keV with doses up to 2.5 X 1018 ions/cm2 and a current density of less than 10 μA/cm2 into Si 〈100〉 at room and liquid nitrogen temperatures. In-situ Rutherford backscattering (RBS) analysis clearly indicates the formation of uniform buried SIO2 for both room and liquid nitrogen temperatures for doses above 1.5 X 1018/cm2.Oxygen ions were implanted at room temperature into crystalline quartz to doses of about 1018 ions cm2 at 150 keV, with a current density of 〈10〉10 μA/cm2. The RBS spectra of the oxygen implanted quartz cannot be distinguished from those of unimplanted ones. Furthermore, Si ions were implanted into crystalline quartz at 80 keV and dose of 1 X 1017 Si/cm2, and a current aensity of about 1 μA/cm2. However, no signal from Si in excess of the SiO2 ratio could be observed. Our results obtained by RBS show that implantation of either Si+ or O into SiO2 under conditions stated above does not create a layer whose Si:O ratio differs measurably from that of SiO2.

Buried Oxide and Silicide Formation by High-Dose Implantation in Silicon

MRS Bulletin ◽  
1992 ◽  
Vol 17 (6) ◽  
pp. 40-46 ◽  
Author(s):  
G.K. Celler ◽  
Alice E. White
Keyword(s):  
Integrated Circuits ◽  
Ion Implantation ◽  
Integrated Circuit ◽  
High Dose ◽  
High Current ◽  
Silicide Formation ◽  
Semiconductor Substrate ◽  
Beam Currents ◽  
New Generation ◽  
High Dose Implantation

Experiments in ion implantation were first performed almost 40 years ago by nuclear physicists. More recently, ion implanters have become permanent fixtures in integrated circuit processing lines. Manufacture of the more complex integrated circuits may involve as many as 10 different ion implantation steps. Implantation is used primarily at f luences of 1012–1015 ions/cm2 to tailor the electrical properties of a semiconductor substrate, but causing only a small perturbation in the composition of the target (see the article by Seidel and Larson in this issue of the MRS Bulletin). Applications of implantation had been limited by the small beam currents that were available, but recently a new generation of high-current implanters has been developed. This high-current capability allows implanting concentrations up to three orders of magnitude higher than those required for doping—enough to create a compound.

Multiply faulted defects in high-current oxygen-implanted silicon-on-insulator

1989 ◽  
Vol 47 ◽  
pp. 606-607
Author(s):  
S. Visitserngtrakul
Keyword(s):  
Electron Microscopy ◽  
High Resolution Electron Microscopy ◽  
Beam Current ◽  
Silicon On Insulator ◽  
High Dose ◽  
High Current ◽  
Implantation Time ◽  
Resolution Electron ◽  
Beam Currents ◽  
Very High

High-dose oxygen implantation into silicon, SIMOX (separation by implantation of oxygen), is a leading technique for producing silicon-on-insulator (SOI) material. Most studies have examined SIMOX prepared with a traditional implanter, which has beam currents of 100 to 400 μA. Since the formation of SIMOX requires a very high dose of oxygen, typically one hundred times larger than the standard dopant implant doses, the process takes many hours. Recently, a high-current implanter has been developed for SIMOX fabrication, which produces a 40 mA beam current. However, the higher current density has not only shortened the implantation time, but also produced features not routinely observed in samples implanted at much lower currents. The study reported here used conventional transmission and high resolution electron microscopy (CTEM,HREM) to characterize microstructure and defects in SIMOX implanted at high currents.

Visible interference effects in silicon caused by high‐current–high‐dose implantation

1976 ◽  
Vol 29 (10) ◽  
pp. 648-651 ◽  
Author(s):  
T. E. Seidel ◽  
G. A. Pasteur ◽  
J. C. C. Tsai
Keyword(s):  
High Dose ◽  
High Current ◽  
Interference Effects ◽  
High Dose Implantation

Carrier mobility degradation due to high dose implantation in ultrathin unstrained and strained silicon-on-insulator films

2007 ◽  
Vol 102 (10) ◽  
pp. 104505 ◽  
Author(s):  
C. Dupré ◽  
T. Ernst ◽  
J.-M. Hartmann ◽  
F. Andrieu ◽  
J.-P. Barnes ◽  
...  
Keyword(s):  
Carrier Mobility ◽  
Silicon On Insulator ◽  
Strained Silicon ◽  
High Dose ◽  
Mobility Degradation ◽  
High Dose Implantation
Sign in / Sign up

Export Citation Format

Share Document