The Effects of Strain Rate and Minor Baron Addition on Brittle-to-Ductile Transition Temperature in Gamma TiAl Alloy

1998 ◽  
Vol 552 ◽  
Author(s):  
Dongliang Lin(T. L. Lin) ◽  
Yu Wang ◽  
Junliang Liu ◽  
Chi C. Law
Keyword(s):  
Strain Rate ◽  
Lamellar Microstructure ◽  
Tensile Fracture ◽  
Transgranular Fracture ◽  
Two Phase ◽  
Fracture Surfaces ◽  
Brittle To Ductile Transition ◽  
Minor Addition ◽  
Transmission Electron ◽  
Dimple Fracture

ABSTRACTBrittle-to-ductile transition (BDT) temperature (TBD) was evaluated according to temperature dependence of tensile properties under different strain rates from 10−5to 10−1s−1in two-phase Ti-47Al-2Mn-2Nb and Ti-47A1–2Mn-2Nb-0.8 TiB2alloys with nearly lamellar microstructure. Based on the strain rate dependence of the determined TBD values, apparent BDT activation energies were determined using Zener-Hollomon factor. Tensile fracture surfaces were observed using a scanning electron microscope while deformation substructures were investigated by transmission electron microscopy. It was found that the BDTT of both alloys increased sharply with the strain rate and that the minor addition of 0.8 vol% TiB2reduced TBD by about 100K at the same strain rate. The TiB2addition also decreases the apparent BDT activation energy from 324 to 256 kJ/mol. Both of these values approximate to self- or inter-diffusion of Ti and Al atoms in TiAl phase. Transgranular fracture and dimple fracture were found dominant in fracture surfaces below and above TBD, respectively. The most common 1/2<110] ordinary dislocations were found to begin climb at mound TBD. All this evidence, as well as a theoretical calculation using the Nabarro Model, add up to a conclusion that the BDT is controlled by dislocation climb in both alloys.

Observation of dislocations in dynamically loaded Cu-SiO2

1986 ◽  
Vol 44 ◽  
pp. 424-425
Author(s):  
D. S. Pritchard
Keyword(s):  
Electron Microscope ◽  
Strain Rate ◽  
Single Crystal ◽  
Transmission Electron Microscope ◽  
Volume Fraction ◽  
Screw Dislocations ◽  
Spherical Inclusions ◽  
Transmission Electron ◽  
Crystal Dispersion ◽  
Strain Rate Loading

The effect of varying the strain rate loading conditions in compression on a copper single crystal dispersion-hardened with SiO2 particles has been examined. These particles appear as small spherical inclusions in the copper lattice and have a volume fraction of 0.6%. The structure of representative crystals was examined prior to any testing on a transmission electron microscope (TEM) to determine the nature of the dislocations initially present in the tested crystals. Only a few scattered edge and screw dislocations were viewed in those specimens.

scholarly journals Revisiting the Bøggild Intergrowth in Iridescent Labradorite Feldspars: Ordering, Kinetics, and Phase Equilibria

Minerals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 727
Author(s):  
Shiyun Jin ◽  
Huifang Xu ◽  
Seungyeol Lee
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Atom Probe ◽  
Phase Region ◽  
Two Phase ◽  
Subsolidus Phase ◽  
Plagioclase Feldspar ◽  
X Ray ◽  
Transmission Electron ◽  
Scanning Transmission

The enigmatic Bøggild intergrowth in iridescent labradorite crystals was revisited in light of recent work on the incommensurately modulated structures in the intermediated plagioclase. Five igneous samples and one metamorphic labradorite sample with various compositions and lamellar thicknesses were studied in this paper. The lamellar textures were characterized with conventional transmission electron microscopy (TEM) and scanning transmission electron microscopy (STEM). The compositions of individual lamellae were analyzed with high-resolution energy-dispersive X-ray spectroscopy (EDS) mapping and atom probe tomography (APT). The average structure states of the studied samples were also compared with single-crystal X-ray diffraction data (SC-XRD). The Na-rich lamellae have a composition of An44–48, and the Ca-rich lamellae range from An56 to An63. Significant differences between the lamellar compositions of different samples were observed. The compositions of the Bøggild intergrowth do not only depend on the bulk compositions, but also on the thermal history of the host rock. The implications on the subsolidus phase relationships of the plagioclase feldspar solid solution are discussed. The results cannot be explained by a regular symmetrical solvus such as the Bøggild gap, but they support an inclined two-phase region that closes at low temperature.

scholarly journals Comparison in Deformation Behavior, Microstructure, and Failure Mechanism of Nickel Base Alloy 625 under Two Strain Rates

Materials ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2652
Author(s):  
Meng Liu ◽  
Quanyi Wang ◽  
Yifan Cai ◽  
Dong Lu ◽  
Tianjian Wang ◽  
...  
Keyword(s):  
Strain Rate ◽  
Deformation Behavior ◽  
Tensile Deformation ◽  
Base Alloy ◽  
Inconel 625 ◽  
Tensile Fracture ◽  
Nickel Base Superalloy ◽  
Strain Rates ◽  
Tensile Fracture Surface ◽  
Nickel Base

Tensile deformation behavior and microstructure of nickel-base superalloy Inconel 625 are investigated under different strain rates of 5 × 10−4 s−1 and 5 × 10−5 s−1. According to the experimental results, yield strength and ultimate tensile strength of the alloy increase with the increase in strain rate in room temperature. Microstructure results indicate that the size of dimples is smaller in the tensile fracture surface at low strain rate than the high strain rate, and the number of dimples is also related to the strain rates and twins appear earlier in the specimens with higher strain rates. Apart from Hollomon and Ludwik functions, a new formula considering the variation trend of strength in different deformation stages is deduced and introduced, which fit closer to the tensile curves of the 625 alloy used in the present work at both strain rates. Furthermore, the Schmid factors of tensile samples under two strain rates are calculated and discussed. In the end, typical work hardening behavior resulting from the dislocations slip behavior under different strain rates is observed, and a shearing phenomenon of slip lines cross through the δ precipitates due to the movement of dislocations is also be note.

scholarly journals Oxygen Induced Phase Transformation in TC21 Alloy with a Lamellar Microstructure

Metals ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 163
Author(s):  
Shu Wang ◽  
Yilong Liang ◽  
Hao Sun ◽  
Xin Feng ◽  
Chaowen Huang
Keyword(s):  
Electron Microscopy ◽  
Phase Transformation ◽  
Oxygen Uptake ◽  
Titanium Alloys ◽  
Electron Backscatter Diffraction ◽  
Lamellar Microstructure ◽  
Α Phase ◽  
Transmission Electron ◽  
The Matrix ◽  
Oxygen Ingress

The main objective of the present study was to understand the oxygen ingress in titanium alloys at high temperatures. Investigations reveal that the oxygen diffusion layer (ODL) caused by oxygen ingress significantly affects the mechanical properties of titanium alloys. In the present study, the high-temperature oxygen ingress behavior of TC21 alloy with a lamellar microstructure was investigated. Microstructural characterizations were analyzed through optical microscopy (OM), scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), and transmission electron microscopy (TEM). Obtained results demonstrate that oxygen-induced phase transformation not only enhances the precipitation of secondary α-phase (αs) and forms more primary α phase (αp), but also promotes the recrystallization of the ODL. It was found that as the temperature of oxygen uptake increases, the thickness of the ODL initially increases and then decreases. The maximum depth of the ODL was obtained for the oxygen uptake temperature of 960 °C. In addition, a gradient microstructure (αp + β + βtrans)/(αp + βtrans)/(αp + β) was observed in the experiment. Meanwhile, it was also found that the hardness and dislocation density in the ODL is higher than that that of the matrix.

Investigation of low- and high-resistance Ni–Ge–Au ohmic contacts to n+ GaAs using electron microbeam and surface analytical techniques

1996 ◽  
Vol 11 (5) ◽  
pp. 1244-1254 ◽  
Author(s):  
Nancy E. Lumpkin ◽  
Gregory R. Lumpkin ◽  
K. S. A. Butcher
Keyword(s):  
Electron Microscopy ◽  
Ohmic Contacts ◽  
Analytical Electron Microscopy ◽  
Depth Profiling ◽  
Analytical Techniques ◽  
Two Phase ◽  
Low Resistance ◽  
Fine Grained ◽  
Multiphase Microstructure ◽  
Transmission Electron

A process for the formation of low-resistance Ni–Ge–Au ohmic contacts to n+ GaAs has been refined using multivariable screening and response surface experiments. Samples from the refined, low-resistance process (which measure 0.05 ± 0.02 Ω · mm) and the unrefined, higher resistance process (0.17 ± 0.02 Ω · mm) were characterized using analytical electron microscopy (AEM), transmission electron microscopy (TEM), scanning electron microscopy-energy dispersive spectroscopy (SEM-EDS), and x-ray photoemission spectroscopy (XPS) depth profiling methods. This approach was used to identify microstructural differences and compare them with electrical resistance measurements. Analytical results of the unrefined ohmic process sample reveal a heterogeneous, multiphase microstructure with a rough alloy-GaAs interface. The sample from the refined ohmic process exhibits an alloy which is homogeneous, smooth, and has a fine-grained microstructure with two uniformly distributed phases. XPS analysis for the refined ohmic process sample indicates that the Ge content is relatively depleted in the alloy (relative to the deposited Ge amount) and enriched in the GaAs. This is not evidenced in the unrefined ohmic process sample. Our data lead us to conclude that a smooth, uniform, two-phase microstructure, coupled with a shift in Ge content from the post-alloy metal to the GaAs, is important in forming low-resistance ohmic contacts.

Characterization of the fracture behaviour of X42 microalloyed pipeline steel

2015 ◽  
Vol 6 (5) ◽  
pp. 567-577
Author(s):  
Halil Ibrahim Ünal ◽  
Hakan Atapek ◽  
Baran Gürkan Beleli ◽  
Seyda Polat ◽  
Serap Gümüs ◽  
...  
Keyword(s):  
Fracture Behaviour ◽  
Pipeline Steel ◽  
Sheet Material ◽  
Sheet Steel ◽  
Grain Morphology ◽  
Tensile Fracture ◽  
Pipe Material ◽  
Content Type ◽  
Fracture Surfaces ◽  
Impact Tests

Purpose – The purpose of this paper is to investigate the fracture of grade X42 microalloyed steel used as pipe material after tensile test at room temperature and impact tests at 0, −20 and −40°C, respectively. Design/methodology/approach – In the first stage of the study, X42 steels in the form of sheet and pipe materials were selected and etched samples were characterized using light microscope. In the second stage, mechanical properties of steels were obtained by microhardness measurements, static tensile and impact tests and all the broken surfaces were examined by scanning electron microscope to determine the fracture type as a function of both microstructure and loading. Findings – The examinations revealed that: first, the sheet material had a typical ferritic-pearlitic matrix, second, the transverse section of the sheet steel exhibited a matrix consisting of polygonal ferrite-aligned pearlite colonies and the longitudinal one had elongated ferrite phase and pearlite colonies in the direction of rolling, third, ferrite and pearlite distribution was different from the sheet material due to multiaxial deformation in the pipe material, fourth, tensile fracture surfaces of the steels had typical dimple fracture induced by microvoid coalescence, fifth, impact fracture surfaces of the steels changed as a function of the test temperature and cleavage fracture mode of ferritic-pearlitic matrix became more dominant as the temperature decreased, and sixth, grain morphology had an effect on the fracture behavior of the steels. Originality/value – The paper explains the fracture behaviour of X42 microalloyed pipeline steel and its fractographical analysis.

Microstructures of two-phase Ti–Cr alloys containing the TiCr2 Laves phase intermetallic

1997 ◽  
Vol 12 (6) ◽  
pp. 1472-1480 ◽  
Author(s):  
Katherine C. Chen ◽  
Samuel M. Allen ◽  
James D. Livingston
Keyword(s):  
Laves Phase ◽  
X Ray Diffraction ◽  
Orientation Relationships ◽  
Phase Growth ◽  
Two Phase ◽  
X Ray ◽  
Lattice Constants ◽  
Annealing Temperatures ◽  
Transmission Electron ◽  
Phase Intermetallic

Microstructures of two-phase Ti–Cr alloys (Ti-rich bcc + TiCr2 and Cr-rich bcc + TiCr2) are analyzed. A variety of TiCr2 precipitate morphologies is encountered with different nominal alloy compositions and annealing temperatures. Lattice constants and crystal structures are determined by x-ray diffraction (XRD) and transmission electron microscopy (TEM). Orientation relationships between the beta bcc solid solution and C15 TiCr2 Laves phase are understood in terms of geometrical packing, and are consistent with a Laves phase growth mechanism involving twinning.

scholarly journals SUPERPLASTIC DEFORMATION OF TWO PHASE MgLiAl ALLOYAFTER TCAP PRESSING.

2017 ◽  
Vol 23 (3) ◽  
pp. 215 ◽  
Author(s):  
Jan Marek Dutkiewicz ◽  
Stanislav Rusz ◽  
Dariusz Kuc ◽  
Ondrej Hilser ◽  
Paweł Pałka ◽  
...  
Keyword(s):  
Strain Rate ◽  
Rate Sensitivity ◽  
Superplastic Forming ◽  
Sensitivity Coefficient ◽  
Strain Rate Range ◽  
Two Phase ◽  
Angular Pressing ◽  
Slip Planes ◽  
Superplastic Properties ◽  
Grain Misorientation

<p>Magnesium based alloy containing 9 wt. % Li, 1,5 wt. % Al, composed of a + b (hcp + bcc) phases was cast under argon atmosphere and extruded at 350<sup>o</sup>C. Up to 3 passes of Twist Channel Angular Pressing TCAP deformation was applied at 160<sup>o</sup>C. TCAP tool consisted of helical part in horizontal area of the channel with angle of lead γ = 30° to simulate back pressure. The initial grain size of hexagonal a phase estimated at 30 mm decreased in following passes down to 6 mm and that of bcc b phase decreased after TCAP from initial 12 mm down to 5 mm. TEM studies after TCAP passes showed higher dislocation density in the b region than in the a phase. Crystallographic relationship (001) a || (110) b indicated parallel positioning of slip planes of both phases. Electron diffraction confirmed increase of grain misorientation with number of TCAP passes. Stress/strain curves measured at temperature 200<sup>o</sup>C showed superplastic forming after 1<sup>st</sup> and 3<sup>rd</sup> TCAP pass. Values of strain rate sensitivity coefficient <em>m</em> were calculated at 0.31 after 1 TCAP pass and increased after 3<sup>rd</sup> TCAP pass up to 0.47 for the strain rate range 10<sup>-5</sup> – 5 10<sup>-4</sup>. Increase of number of TCAP passes had positive effect on superplastic properties due to finer grains and increase of their misorientation;</p>

Correlation of Dynamic Response with Adiabatic Shearing Behavior in Ti–10V–2Fe–3Al Alloy

2011 ◽  
Vol 284-286 ◽  
pp. 1542-1545 ◽  
Author(s):  
Qing Wen Ding ◽  
Yu Ren ◽  
Cheng Wen Tan ◽  
Jing Zhang ◽  
Xiao Dong Yu
Keyword(s):  
Strain Rate ◽  
Split Hopkinson Pressure Bar ◽  
Shear Bands ◽  
Lamellar Microstructure ◽  
Hopkinson Pressure Bar ◽  
Adiabatic Shearing ◽  
Critical Strain Rate ◽  
Microstructure Examination ◽  
Split Hopkinson ◽  
Pressure Bar

A Split Hopkinson Pressure Bar system was employed to investigate the compressive dynamic mechanical behaviors of Ti-10V-2Fe-3Al (Ti-1023) alloy with lamellar microstructure, over a broad strain rates ranging from 1500/s to 5100/s. The results reveal that the strain rate has a significant effect on the flow stress of Ti-1023 alloy, and there exists serious thermal softening as the strain rate exceeds 3200/s. The critical strain rate of fracture for this alloy is 2300/s. The microstructure examination indicated that adiabatic shear bands (ASBs) bifurcate more intensely with the increasing of strain rate. Micro-voids nucleate either in the ASB or interface between shear band and matrix bulk. Finally, fracture of this alloy proceeds through the nucleation, growth and coalescence of these voids and cracks along the ASBs.

Microstructure and Tensile Behavior of Ti-Rich Ti-Ni-Cu Melt-Spun Ribbon

2014 ◽  
Vol 936 ◽  
pp. 1163-1167
Author(s):  
Wen Jun He ◽  
Guang Hui Min ◽  
Oleg Tolochko
Keyword(s):  
Melt Spinning ◽  
Tensile Deformation ◽  
Amorphous Ribbon ◽  
Fracture Morphology ◽  
Tensile Tests ◽  
Tensile Fracture ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Annealed Ribbon ◽  
Martensitic State

Microstructure and mechanical properties of Ti51.5Ni25Cu23.5 ribbon fabricated by melt spinning were investigated by X-ray diffraction (XRD), transmission electron microscopy (TEM) and tensile tests. Some B19 martensite crystalline with (011) compound twin was embedded in the mainly amorphous ribbon, while the ribbon annealed at 450°C for 1 h is at fully martensitic state. Annealing process alter the preferential orientation from (022)-B19 to (111)-B19. Tensile fracture stresses of as-spun ribbon and the annealed ribbon are 1257 MPa and 250 MPa, respectively. The tensile fracture morphology of as-spun ribbon shows typical vein fringe while that of the annealed ribbon reveals fine but depth-inhomogeneous dimples. After tensile deformation, the annealed ribbon exhibits typical martensitic detwinning behavior accompanying with the strain contrast.

Sign in / Sign up

Export Citation Format

Share Document