Characterization of Plated Cu Thin Film Microstructures

1999 ◽  
Vol 564 ◽  
Author(s):  
L. M. Gignac ◽  
K. P. Rodbel ◽  
C. Cabral ◽  
P. C. Andricacos ◽  
P. M. Rice ◽  
...  
Keyword(s):  
Focused Ion Beam ◽  
Ion Beam ◽  
Grain Structure ◽  
Grain Structures ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
Gaussian Fit ◽  
Cu Thin Film ◽  
Log Normal ◽  
Electron Imaging

AbstractElectroplated Cu was found to have a fine as-plated microstructure, 0.05 ± 0.03 μm, with multiple grains through the film thickness and evidence of twins and dislocations within grains. Over time at room temperature, the grains grew to greater than 1 μm in size. Studied as a function of annealing temperature, the recrystallized grains were shown to be 1.6 ± 1.0 μm in size, columnar and highly twinned. The grain growth was directly related to the time dependent decrease in sheet resistance. The initial grain structure was characterized using scanning transmission electron microscopy (STEM) from a cross-section sample prepared by a novel focused ion beam (FIB) and lift-out technique. The recrystallized grain structures were imaged using FIB secondary electron imaging. From these micrographs, the grain boundary structures were traced, and an image analysis program was used to measure the grain areas. A Gaussian fit of the log-normal distribution of grain areas was used to calculate the mean area and standard deviation. These values were converted to grain size diameters by assuming a circular grain geometry.

Characterization of Plated Cu Thin Film Microstructures

1999 ◽  
Vol 562 ◽  
Author(s):  
L. M. Gignac ◽  
K. P. Rodbell ◽  
C. Cabral ◽  
P. C. Andricacos ◽  
P. M. Rice ◽  
...  
Keyword(s):  
Focused Ion Beam ◽  
Ion Beam ◽  
Grain Structure ◽  
Grain Structures ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
Gaussian Fit ◽  
Cu Thin Film ◽  
Log Normal ◽  
Electron Imaging

ABSTRACTElectroplated Cu was found to have a fine as-plated microstructure, 0.05 ±0.03 μm, with multiple grains through the film thickness and evidence of twins and dislocations within grains. Over time at room temperature, the grains grew to greater than 1 μm in size. Studied as a function of annealing temperature, the recrystallized grains were shown to be 1.6 ± 1.0 μm in size, columnar and highly twinned. The grain growth was directly related to the time dependent decrease in sheet resistance. The initial grain structure was characterized using scanning transmission electron microscopy (STEM) from a cross-section sample prepared by a novel focused ion beam (FIB) and lift-out technique. The recrystallized grain structures were imaged using FIB secondary electron imaging. From these micrographs, the grain boundary structures were traced, and an image analysis program was used to measure the grain areas. A Gaussian fit of the log-normal distribution of grain areas was used to calculate the mean area and standard deviation. These values were converted to grain size diameters by assuming a circular grain geometry.

3D Observation of Elemental Distribution of Si-Device using a Dedicated FIB/STEM System

2005 ◽  
Author(s):  
T. Yaguchi ◽  
M. Konno ◽  
T. Kamino ◽  
M. Ogasawara ◽  
K. Kaji ◽  
...  
Keyword(s):  
Focused Ion Beam ◽  
Ion Beam ◽  
Three Dimensional ◽  
Elemental Distribution ◽  
Multivariate Statistical ◽  
X Ray ◽  
Sample Rotation ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
Elemental Maps

Abstract A technique for preparation of a pillar shaped sample and its multi-directional observation of the sample using a focused ion beam (FIB) / scanning transmission electron microscopy (STEM) system has been developed. The system employs an FIB/STEM compatible sample rotation holder with a specially designed rotation mechanism, which allows the sample to be rotated 360 degrees [1-3]. This technique was used for the three dimensional (3D) elemental mapping of a contact plug of a Si device in 90 nm technology. A specimen containing a contact plug was shaped to a pillar sample with a cross section of 200 nm x 200 nm and a 5 um length. Elemental analysis was performed with a 200 kV HD-2300 STEM equipped with the EDAX genesis Energy dispersive X-ray spectroscopy (EDX) system. Spectrum imaging combined with multivariate statistical analysis (MSA) [4, 5] was used to enhance the weak X-ray signals of the doped area, which contain a low concentration of As-K. The distributions of elements, especially the dopant As, were successfully enhanced by MSA. The elemental maps were .. reconstructed from the maps.

Physical Failure Analysis Techniques for Front-End-of-Line Defect Analysis

2016 ◽  
Author(s):  
Dirk Doyle ◽  
Lawrence Benedict ◽  
Fritz Christian Awitan
Keyword(s):  
Cross Section ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Gate Oxide ◽  
Top Down ◽  
New Techniques ◽  
First Case ◽  
Transmission Electron ◽  
Scanning Transmission

Abstract Novel techniques to expose substrate-level defects are presented in this paper. New techniques such as inter-layer dielectric (ILD) thinning, high keV imaging, and XeF2 poly etch overflow are introduced. We describe these techniques as applied to two different defects types at FEOL. In the first case, by using ILD thinning and high keV imaging, coupled with focused ion beam (FIB) cross section and scanning transmission electron microscopy (STEM,) we were able to judge where to sample for TEM from a top down perspective while simultaneously providing the top down images giving both perspectives on the same sample. In the second case we show retention of the poly Si short after removal of CoSi2 formation on poly. Removal of the CoSi2 exposes the poly Si such that we can utilize XeF2 to remove poly without damaging gate oxide to reveal pinhole defects in the gate oxide. Overall, using these techniques have led to 1) increased chances of successfully finding the defects, 2) better characterization of the defects by having a planar view perspective and 3) reduced time in localizing defects compared to performing cross section alone.

scholarly journals An Analysis of Li Ion Secondary Battery Materials by Using Focused Ion Beam Micro-sampling Technique and Cold Field Emission Scanning Transmission Electron Microscope

2010 ◽  
Vol 16 (S2) ◽  
pp. 214-215
Author(s):  
T Tanigaki ◽  
K Ito ◽  
K Nakamura ◽  
Y Nagakubo ◽  
J Azuma ◽  
...  
Keyword(s):  
Electron Microscope ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Sampling Technique ◽  
Scanning Transmission Electron Microscope ◽  
Battery Materials ◽  
Secondary Battery ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
Li Ion

Extended abstract of a paper presented at Microscopy and Microanalysis 2010 in Portland, Oregon, USA, August 1 – August 5, 2010.

scholarly journals Stem-EDX and FIB-SEM Tomography of ALLVAC 718Plus Superalloy

2016 ◽  
Vol 61 (2) ◽  
pp. 535-542 ◽  
Author(s):  
A. Kruk ◽  
G. Cempura ◽  
S. Lech ◽  
A. Czyrska -Filemonowicz
Keyword(s):  
Electron Microscope ◽  
Focused Ion Beam ◽  
Electron Tomography ◽  
Ion Beam ◽  
High Strength ◽  
Strengthening Mechanism ◽  
Scanning Transmission Electron Microscope ◽  
Particle Analysis ◽  
Transmission Electron ◽  
Scanning Transmission

Abstract Allvac 718Plus (718Plus) is a high strength, corrosion resistant nickel- based superalloy used for application in power generation, aeronautics and aerospace industry. The 718Plus microstructure consists of a γ matrix with γ’-Ni3(Al,Ti) and some δ- Ni3Nb phases as well as lamellar particles (η-Ni3Ti, η*-Ni6AlNb or Ni6(Al,Ti)Nb) precipitated at the grain boundaries. The primary strengthening mechanism for this alloy is a precipitation hardening, therefore size and distribution of precipitates are critical for the performance of the alloy. The aim of this study was to characterize precipitates in the 718Plus superalloy using Scanning Transmission Electron Microscope combined with Energy Dispersive X-ray Spectroscopy (STEM-EDX) and Focused Ion Beam Scanning Electron Microscope (FIB-SEM). The STEM-EDX and FIB-SEM tomography techniques were used for 3D imaging and metrology of the precipitates. Transmission electron microscopy and EDX spectroscopy were used to reveal details of the 718Plus microstructure and allow determine chemical composition of the phases. The study showed that electron tomography techniques permit to obtain complementary information about microstructural features (precipitates size, shape and their 3D distribution) in the reconstructed volume with comparison to conventional particle analysis methods, e.g. quantitative TEM and SEM metallography

scholarly journals Cyanobacterial calcification in modern microbialites at the submicrometer-scale

2013 ◽  
Vol 10 (2) ◽  
pp. 3311-3339 ◽  
Author(s):  
E. Couradeau ◽  
K. Benzerara ◽  
E. Gérard ◽  
I. Estève ◽  
D. Moreira ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Cell Morphology ◽  
Laser Scanning ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Laser Scanning Microscopy ◽  
Confocal Laser ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
Advanced Stages

Abstract. The search for microfossils in the geological record has been a long-term challenge. Part of the problem comes from the difficulty of identifying such microfossils unambiguously, since they can be morphologically confused with abiotic biomorphs. One route to improve our ability to correctly identify microfossils consists in studying fossilization processes affecting bacteria in modern settings. We studied the initial stages of fossilization of cyanobacterial cells in modern microbialites from Lake Alchichica (Mexico), a Mg-rich hyperalkaline crater lake (pH 8.9) hosting currently growing stromatolites composed of aragonite [CaCO3] and hydromagnesite [Mg5(CO3)4(OH)2 × 4(H2O)]. Most of the biomass associated with the microbialites is composed of cyanobacteria. Scanning electron microscopy analyses coupled with confocal laser scanning microscopy observations were conducted to co-localize cyanobacterial cells and associated minerals. These observations showed that cyanobacterial cells affiliating to the order Pleurocapsales become specifically encrusted within aragonite with an apparent preservation of cell morphology. Encrustation gradients from non-encrusted to totally encrusted cells spanning distances of a few hundred micrometers were observed. Cells exhibiting increased levels of encrustation along this gradient were studied down to the nm-scale using a combination of focused ion beam (FIB) milling, transmission electron microscopy (TEM) and scanning transmission X-ray microscopy (STXM) at the C, O and N K-edges. Two different types of aragonite crystals were observed: one type was composed of needle-shaped nano-crystals growing outward from the cell body with a crystallographic orientation perpendicular to the cell wall, and another type was composed of larger crystals that progressively filled the cell interior. Organic matter (OM), initially co-localized with the cell, decreased in concentration and dispersed away from the cell while crystal growth occurred. As encrustation developed, OM progressively disappeared, but remaining OM showed the same spectroscopic signature. In the most advanced stages of fossilization, only the textural organization of the two types of aragonite recorded the initial cell morphology and spatial distribution.

The Method for Retaining an Intermittent Electrical Failure Signature during the Interconnect Immobilization Process throughout Failure Analysis

2009 ◽  
Author(s):  
Julie Schuchman ◽  
Julie Willis
Keyword(s):  
Sample Preparation ◽  
First Generation ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Scanning Transmission Electron Microscope ◽  
Electrical Failure ◽  
Dual Beam ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
Material Sample

Abstract This paper deals primarily with the difficulties and solutions to scanning transmission electron microscope (STEM) sample preparation by dual beam focused ion beam. Approximately twenty major challenges were encountered spanning hardware, software, and material sample preparation. The main focus is upon the variety of challenges which are encountered in trying to implement automated STEM and TEM sample fabrication with minimal operator input and the engineering solutions implemented to overcome these challenges. The automated STEM script has evolved significantly from the first generation attempt and is described in more detail in this paper. The mechanical, software, and materials challenges encountered are also presented. The paper highlights a mechanical issue with the ion aperture motor mechanism, which required extensive troubleshooting to fully diagnose and correct. A long standing software routine had to be modified to fully enable script automation by extending the beam dwell time of the automatic brightness contrast routine.

Applications of In-situ Sample Preparation and Modeling of SEM-STEM Imaging

2008 ◽  
Author(s):  
R.J. Young ◽  
A. Buxbaum ◽  
B. Peterson ◽  
R. Schampers
Keyword(s):  
Sample Preparation ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Dual Beam ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
Electron Microscopes ◽  
Scanning Electron Microscopes ◽  
Preparation Techniques

Abstract Scanning transmission electron microscopy with scanning electron microscopes (SEM-STEM) has become increasing used in both SEM and dual-beam focused ion beam (FIB)-SEM systems. This paper describes modeling undertaken to simulate the contrast seen in such images. Such modeling provides the ability to help understand and optimize imaging conditions and also support improved sample preparation techniques.

Analysis of Geometrical and Microstructural Effects on Void Formation in Metallization: Observation and Modelling

1996 ◽  
Vol 428 ◽  
Author(s):  
W. C. Shih ◽  
A. Ghiti ◽  
K. S. Low ◽  
A. L. Greer ◽  
A. G. O'Neill ◽  
...  
Keyword(s):  
Focused Ion Beam ◽  
Ion Beam ◽  
Void Formation ◽  
Grain Structure ◽  
Flux Divergence ◽  
Damage Development ◽  
Temperature Variations ◽  
Atomic Flux ◽  
Grain Structures ◽  
Microstructural Effects

AbstractThis paper reports the analysis of geometrical and microstructural effects on void formation in interconnects. Ion-beam machining is used to define segments for study at the cathode end of test lines. Scanning electron microscopy is used to observe damage development, focused ion beam microscopy to observe the corresponding grain structure. Finite-element calculations of self-consistent current density and temperature distributions in the conductor are used to predict damage locations both for a continuum material and for simulated grain structures. Cross-section changes in the line give temperature variations leading to divergences in atomic flux. Regions of high flux divergence are favoured for electromigration damage, but the precise sites of damage are determined by the grain structure, as shown both in the experiment and in the modelling.

Sign in / Sign up

Export Citation Format

Share Document