Characterization of Si, SiGe and SOI Structures Using Photoluminescence

1999 ◽  
Vol 588 ◽  
Author(s):  
V. Higgs
Keyword(s):  
Focused Ion Beam ◽  
Secondary Ion Mass Spectrometry ◽  
Ion Beam ◽  
Surface Region ◽  
Misfit Dislocations ◽  
Near Surface ◽  
Pl Mapping ◽  
Excitation Laser ◽  
Pl Intensity ◽  
P Type

AbstractA new Photoluminescence (PL) method has been developed to detect defects in the near surface region of Si wafers and Si-on-insulator (SOI) structures. Wafer maps (up to 300 min diameter) can be readily acquired and areas of interest can be scanned at high resolution (≈1 μm). The excitation laser beam is modulated to confine the photogenerated carriers; defects are observed due to the localised reduction of the carrier lifetime. Si p-type (10 Ohm.cm) wafers were intentionally contaminated with various levels of Ni and Fe (1×109−5×1010 atoms/cm2) and annealed. The PL intensity was observed to decrease due to the metal related non-radiative defects. Whereas in contrast, for Cu, (1×109−5×1010 atoms/cm2) the PL intensity actually increased initially and reached a maximum value at 5×109 atoms/cm2. It is suggested that during contamination the Cu related defects have complexed with existing defects (that have stronger recombination properties) and increased the PL. Further Cu contamination (1×1010−5×1010 atoms/cm2) produced a reduction in the PL intensity. PL mapping of strained SiGe epilayers showed that misfit dislocations can be detected and PL can be used to evaluate material quality.PL maps of SOI bonded wafers revealed that the non-bonded areas, voids or gas bubbles could be detected. This was confirmed using defect etching and polishing, voids as small as ≈30 μm in diameter could be detected. SOI wafers fabricated using the separation by implanted oxygen (SIMOX) technique were also analysed, variations in the recombination properties of the layer could be observed. Further inspection using transmission electron microscopy (TEM) revealed that the defects were non-uniformities of the buried oxide covering several microns and containing tetrahedral stacking faults. Focused ion beam (FIB) milling and secondary ion mass spectrometry (SIMS) showed that these defects were at the Si/SiO2 interface and were chemically different to the surrounding area.

Direct Plan View FIB Liftout for Near-Surface Defect Analysis in TEM

2013 ◽  
Author(s):  
Max L. Lifson ◽  
Carla M. Chapman ◽  
D. Philip Pokrinchak ◽  
Phyllis J. Campbell ◽  
Greg S. Chrisman ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Silicon Germanium ◽  
Focused Ion Beam ◽  
Surface Defects ◽  
Ion Beam ◽  
Misfit Dislocations ◽  
Tem Analysis ◽  
Plan View ◽  
Near Surface ◽  
Straightforward Method

Abstract Plan view TEM imaging is a powerful technique for failure analysis and semiconductor process characterization. Sample preparation for near-surface defects requires additional care, as the surface of the sample needs to be protected to avoid unintentionally induced damage. This paper demonstrates a straightforward method to create plan view samples in a dual beam focused ion beam (FIB) for TEM studies of near-surface defects, such as misfit dislocations in heteroepitaxial growths. Results show that misfit dislocations are easily imaged in bright-field TEM and STEM for silicon-germanium epitaxial growth. Since FIB tools are ubiquitous in semiconductor failure analysis labs today, the plan view method presented provides a quick to implement, fast, consistent, and straightforward method of generating samples for TEM analysis. While this technique has been optimized for near-surface defects, it can be used with any application requiring plan view TEM analysis.

scholarly journals Site Specific Three-dimensional Structural Analysis in Tissues and Cells Using Automated DualBeam Slice &View

2007 ◽  
Vol 15 (2) ◽  
pp. 26-31 ◽  
Author(s):  
Ben Lich
Keyword(s):  
Electron Microscopy ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Three Dimensional ◽  
Surface Region ◽  
Dimensional Structure ◽  
Near Surface ◽  
Imaging Capability ◽  
Fluorescent Markers ◽  
Confocal And Electron Microscopy

DualBeam instruments that combine the imaging capability of scanning electron microscopy (SEM) with the cutting and deposition capability of a focused ion beam (FIB) provide biologists with a powerful tool for investigating three-dimensional structure with nanoscale (1 nm-100 nm) resolution. Ever since Van Leeuwenhoek used the first microscope to describe bacteria more than 300 years ago, microscopy has played a central role in scientists' efforts to understand biological systems. Light microscopy is generally limited to a useful resolution of about a micrometer. More recently the use of confocal and electron microscopy has enabled investigations at higher resolution. Used with fluorescent markers, confocal microscopy can detect and localize molecular scale features, but its imaging resolution is still limited. SEM is capable of nanometer resolution, but is limited to the near surface region of the sample.

Influence of Low-Temperature Argon Ion-Beam Treatment on the Photovoltage Spectra of Standard Cz Si Wafers

2007 ◽  
Vol 131-133 ◽  
pp. 333-338 ◽  
Author(s):  
Anis M. Saad ◽  
Olga V. Zinchuk ◽  
N.A. Drozdov ◽  
A.K. Fedotov ◽  
A.V. Mazanik
Keyword(s):  
Low Temperature ◽  
Spectral Region ◽  
Ion Beam ◽  
Surface Region ◽  
Near Surface ◽  
Ion Energy ◽  
Ion Beam Treatment ◽  
P Type ◽  
20 Nm ◽  
Argon Ion

The main goal of this work is to investigate the influence of low-temperature argon ionbeam treatment on the electric and structural properties of a near-surface region of the standard commercial p-type Cz Si wafers, and to compare the effects of Ar+ and H+ ion-beam treatment. The measurements of thermo-EMF have shown that both Ar+ and H+ ion-beam treatment with the ion energy 200 eV and current density 0.15 mA/cm2 at a temperature of 30 oC during 30 min leads to the p-to-n −type overcompensation of the near-surface layer of silicon wafers. The measurements of photovoltage spectra have shown that (i) Ar+ and H+ treatments in like manner lead to the appearance of a photovoltage signal over a wide spectral region due to the formation of p-n-junction on the treated surface, and (ii) photosensitivity of the Ar+ ion-beam treated wafers in the ultraviolet (UV) spectral region (200-400 nm) is much greater as compared to the wafers subjected to H+ ion beam treatment in the same conditions. The main difference in the Ar+ and H+ ion-beam treatment effects is the formation of a thin (5-20 nm) oxygen-containing dielectric layer on the surface of hydrogenated samples and the absence of such layer in case of Ar+ ion-beam treatment.

The Novel Dopant Profile Inspection Methodology by FIB

2010 ◽  
Author(s):  
Po Fu Chou ◽  
Li Ming Lu
Keyword(s):  
High Resolution ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Real Sample ◽  
Physical Analysis ◽  
The Novel ◽  
High Contrast ◽  
Dopant Profile ◽  
P Type

Abstract Dopant profile inspection is one of the focused ion beam (FIB) physical analysis applications. This paper presents a technique for characterizing P-V dopant regions in silicon by using a FIB methodology. This technique builds on published work for backside FIB navigation, in which n-well contrast is observed. The paper demonstrates that the technique can distinguish both n- and p-type dopant regions. The capability for imaging real sample dopant regions on current fabricated devices is also demonstrated. SEM DC and FIB DC are complementary methodologies for the inspection of dopants. The advantage of the SEM DC method is high resolution and the advantage of FIB DC methodology is high contrast, especially evident in a deep N-well region.

Amortization and Recrystallization of 6H-SiC by ion Beam Irradiation

1994 ◽  
Vol 339 ◽  
Author(s):  
V. Heera ◽  
R. Kögler ◽  
W. Skorupa ◽  
J. Stoemenos
Keyword(s):  
Ion Irradiation ◽  
Ion Beam ◽  
Surface Region ◽  
Ion Beam Irradiation ◽  
Surface Layers ◽  
Near Surface ◽  
Transmission Electron ◽  
Amorphous Surface ◽  
Amorphous Sic

ABSTRACTThe evolution of the damage in the near surface region of single crystalline 6H-SiC generated by 200 keV Ge+ ion implantation at room temperature (RT) was investigated by Rutherford backscattering spectroscopy/chanelling (RBS/C). The threshold dose for amorphization was found to be about 3 · 1014 cm-2, Amorphous surface layers produced with Ge+ ion doses above the threshold were partly annealed by 300 keV Si+ ion beam induced epitaxial crystallization (IBIEC) at a relatively low temperature of 480°C For comparison, temperatures of at least 1450°C are necessary to recrystallize amorphous SiC layers without assisting ion irradiation. The structure and quality of both the amorphous and recrystallized layers were characterized by cross-section transmission electron microscopy (XTEM). Density changes of SiC due to amorphization were measured by step height measurements.

Defects Introduced by Plasma Processing of Silicon

1992 ◽  
Vol 262 ◽  
Author(s):  
J. L. Benton
Keyword(s):  
Bulk Material ◽  
Surface Region ◽  
Surface Damage ◽  
Near Surface ◽  
Enhanced Diffusion ◽  
Interstitial Defect ◽  
Comprehensive Picture ◽  
Reaction Region ◽  
Defect Reactions ◽  
P Type

ABSTRACTThe electrical and optical properties of defects introduced by Reactive Ion Etching (RIE) in the near surface region of Si after dry etching with various gases and plasma conditions is studied with spreading Resistance (SR), photoluminescence (PL), and capacitance-voltage profiling (C-V). Plasma etching in chlorine and fluorine based gases produce donors at the surface in both n-type and p-type, Czochralski and float-zone silicon. Isochronal annealing reveals the presence of two distinct regions of dopant compensation. The surface damage region is confined to 1000 Å and survives heat treatment at 400°C, while the defect reaction region extends ≥ 1 μm in depth and recovers by 250°C. A comprehensive picture of the interstitial defect reactions in RIE silicon is completed. The interstitial defects, Ci and Bi, created in the ion damaged near surface region, undergo recombination enhanced diffusion caused by the presence of ultraviolet light in the plasma, resulting in the long range diffusion into the Si bulk. Subsequently, the interstitial atoms are trapped by the background impurities forming the defect pairs, CiOi, CSCi, or BiOi, which are observed experimentally. The depth of the diffusion-limited trapping and the probability of forming specific pairs depends on the relative concentrations of the reactants, oxygen, carbon or boron, present in the bulk material.

scholarly journals Assessment of wear micromechanisms on a laser textured cemented carbide tool during abrasive-like machining by FIB/FESEM

Friction ◽  
2020 ◽  
Author(s):  
Shiqi Fang ◽  
Dirk Bähre ◽  
Luis Llanes
Keyword(s):  
Focused Ion Beam ◽  
Ion Beam ◽  
Local Level ◽  
Surface Texturing ◽  
Laser Surface ◽  
Laser Surface Texturing ◽  
Near Surface ◽  
Dual Beam ◽  
Cemented Carbide Tool ◽  
Microstructural Integrity

Abstract The combined use of focused ion beam (FIB) milling and field-emission scanning electron microscopy inspection (FESEM) is a unique and successful approach for assessment of near-surface phenomena at specific and selected locations. In this study, a FIB/FESEM dual-beam platform was implemented to docment and analyze the wear micromechanisms on a laser-surface textured (LST) hardmetal (HM) tool. In particular, changes in surface and microstructural integrity of the laser-sculptured pyramids (effective cutting microfeatures) were characterized after testing the LST-HM tool against a steel workpiece in a workbench designed to simulate an external honing process. It was demonstrated that: (1) laser-surface texturing does not degrade the intrinsic surface integrity and tool effectiveness of HM pyramids; and (2) there exists a correlation between the wear and loading of shaped pyramids at the local level. Hence, the enhanced performance of the laser-textured tool should consider the pyramid geometry aspects rather than the microstructure assemblage of the HM grade used, at least for attempted abrasive applications.

scholarly journals Highly Rectifying Heterojunctions Formed by Annealed ZnO Nanorods on GaN Substrates

Nanomaterials ◽  
2020 ◽  
Vol 10 (3) ◽  
pp. 508 ◽  
Author(s):  
Stanislav Tiagulskyi ◽  
Roman Yatskiv ◽  
Hana Faitová ◽  
Šárka Kučerová ◽  
David Roesel ◽  
...  
Keyword(s):  
Electrical Properties ◽  
Leakage Current ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Zno Nanorods ◽  
Carrier Injection ◽  
Ion Beam Lithography ◽  
Current Voltage ◽  
P Type ◽  
Surface Leakage

We study the effect of thermal annealing on the electrical properties of the nanoscale p-n heterojunctions based on single n-type ZnO nanorods on p-type GaN substrates. The ZnO nanorods are prepared by chemical bath deposition on both plain GaN substrates and on the substrates locally patterned by focused ion beam lithography. Electrical properties of single nanorod heterojunctions are measured with a nanoprobe in the vacuum chamber of a scanning electron microscope. The focused ion beam lithography provides a uniform nucleation of ZnO, which results in a uniform growth of ZnO nanorods. The specific configuration of the interface between the ZnO nanorods and GaN substrate created by the focused ion beam suppresses the surface leakage current and improves the current-voltage characteristics. Further improvement of the electrical characteristics is achieved by annealing of the structures in nitrogen, which limits the defect-mediated leakage current and increases the carrier injection efficiency.

Sign in / Sign up

Export Citation Format

Share Document