Cu and Dilute Binary Cu(Ti), Cu(Sn) and Cu(Al) Thin Films: Texture, Grain Growth and Resistivity

2002 ◽  
Vol 721 ◽  
Author(s):  
A. Gungor ◽  
K. Barmak ◽  
A. D. Rollett ◽  
C. Cabral ◽  
J. M. E. Harper
Keyword(s):  
Electron Microscopy ◽  
Thin Films ◽  
Transmission Electron Microscopy ◽  
Grain Size ◽  
Electrical Resistivity ◽  
Fiber Texture ◽  
Al Alloy ◽  
Alloy Films ◽  
Transmission Electron ◽  
Pure Cu

AbstractAnnealing Cu and dilute Cu(Ti), Cu(Sn) and Cu(Al) alloy films resulted in the strengthening of film texture, with the strongest <111> fiber texture being found for Cu(Ti). Annealing also resulted in a decrease of electrical resistivity and the growth of grains, with the largest grain size and lowest resistivity being seen for pure Cu itself. Among the alloy films, the lowest resistivity was found for Cu(Ti) and the largest grain size for Cu(Al). Electron beam evaporated films with compositions in the range of 2.0-3.0 at% and thicknesses in the range of 420-540 nm were annealed at 400°C for 5 hours. Four point probe resistance measurement, xray diffraction and transmission electron microscopy were used to follow the changes in film resistivity, texture and grain size.

Homogeneous Al-Ti and Al-Ti-Si Thin Alloy Films

1985 ◽  
Vol 54 ◽  
Author(s):  
Albertus G. Dirks ◽  
Tien Tien ◽  
Janet M. Towner
Keyword(s):  
Thin Films ◽  
Heat Treatment ◽  
Grain Size ◽  
Electrical Resistivity ◽  
Phase Formation ◽  
Alloy Composition ◽  
Al Alloy ◽  
Second Phase ◽  
Alloy Films ◽  
Microstructure And Properties

ABSTRACTThe microstructure and properties of thin films depends strongly upon the alloy composition. A study was made of the metallurgical aspects of homogeneous Al alloy films, particularly the binary Al-Ti and the ternary Al-Ti-Si systems. Electrical resistivity, grain size morphology, second phase formation and electromigration have been studied as a function of the alloy composition and its heat treatment.

TEM Study of FePt and FePt:C/FePt Composite Double-Layered Thin Films

2013 ◽  
Vol 275-277 ◽  
pp. 1952-1955
Author(s):  
Ling Fang Jin ◽  
Xing Zhong Li
Keyword(s):  
Electron Microscopy ◽  
Thin Films ◽  
Transmission Electron Microscopy ◽  
Grain Size ◽  
Magnetic Properties ◽  
Composite Layer ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron

New functional nanocomposite FePt:C thin films with FePt underlayers were synthesized by noneptaxial growth. The effect of the FePt layer on the ordering, orientation and magnetic properties of the composite layer has been investigated by adjusting FePt underlayer thickness from 2 nm to 14 nm. Transmission electron microscopy (TEM), together with x-ray diffraction (XRD), has been used to check the growth of the double-layered films and to study the microstructure, including the grain size, shape, orientation and distribution. XRD scans reveal that the orientation of the films was dependent on FePt underlayer thickness. In this paper, the TEM studies of both single-layered nonepitaxially grown FePt and FePt:C composite L10 phase and double-layered deposition FePt:C/FePt are presented.

Texture and Grain Size of Permalloy Thin Films Sputtered on Silicon With Cr, Ta and SiO2 Buffer Layers

1994 ◽  
Vol 343 ◽  
Author(s):  
P. Galtier ◽  
R. Jerome ◽  
T. Valet
Keyword(s):  
Electron Microscopy ◽  
Thin Films ◽  
Transmission Electron Microscopy ◽  
Grain Size ◽  
Structural Properties ◽  
Buffer Layers ◽  
Transmission Electron ◽  
Magnetic Softness ◽  
Permalloy Thin Films

ABSTRACTWe have investigated the structural properties of Ni80Fe20 thin films sputtered on silicon with Cr, Ta and SiO2 buffer layers using transmission electron microscopy. We observe a decrease of the grain size when Ta and SiO2 underlayers are used instead of Cr. Permalloy films deposited on Ta layers are strongly (111) textured while those grown on Cr and SiO2 are mostly randomly oriented. The results are discussed with respect to the nanostructure of both Ta, Cr and SiO2 underlayers and in relation to the variation of the magnetic softness observed in this system.

Transmission Electron Microscopy studies of texture of Cr underlayer of magnetic recording hard disk

1991 ◽  
Vol 49 ◽  
pp. 580-581
Author(s):  
L. Tang ◽  
G. Thomas ◽  
M. R. Khan ◽  
S. L. Duan
Keyword(s):  
Electron Microscopy ◽  
Thin Films ◽  
Transmission Electron Microscopy ◽  
Magnetic Recording ◽  
Magnetic Thin Films ◽  
Magnetic Films ◽  
Substrate Bias ◽  
Epitaxial Relationship ◽  
Transmission Electron

Cr thin films are often used as underlayers for Co alloy magnetic thin films, such as Co1, CoNi2, and CoNiCr3, for high density longitudinal magnetic recording. It is belived that the role of the Cr underlayer is to control the growth and texture of the Co alloy magnetic thin films, and, then, to increase the in plane coercivity of the films. Although many epitaxial relationship between the Cr underlayer and the magnetic films, such as ﹛1010﹜Co/ {110﹜Cr4, ﹛2110﹜Co/ ﹛001﹜Cr5, ﹛0002﹜Co/﹛110﹜Cr6, have been suggested and appear to be related to the Cr thickness, the texture of the Cr underlayer itself is still not understood very well. In this study, the texture of a 2000 Å thick Cr underlayer on Nip/Al substrate for thin films of (Co75Ni25)1-xTix dc-sputtered with - 200 V substrate bias is investigated by electron microscopy.

Transmission Electron Microscopy of Evaporated Perylene Thin Films

1990 ◽  
Vol 48 (2) ◽  
pp. 336-337
Author(s):  
C. Ewins ◽  
J.R. Fryer
Keyword(s):  
Electron Microscopy ◽  
Thin Films ◽  
Transmission Electron Microscopy ◽  
Molecular Electronics ◽  
High Vacuum ◽  
Amorphous Layer ◽  
Electric Heater ◽  
Transmission Electron ◽  
Polycyclic Aromatic

The preparation of thin films of organic molecules is currently receiving much attention because of the need to produce good quality thin films for molecular electronics. We have produced thin films of the polycyclic aromatic, perylene C10H12 by evaporation under high vacuum onto a potassium chloride (KCl) substrate. The role of substrate temperature in determining the morphology and crystallography of the films was then investigated by transmission electron microscopy (TEM).The substrate studied was the (001) face of a freshly cleaved crystal of KCl. The temperature of the KCl was controlled by an electric heater or a cold finger. The KCl was heated to 200°C under a vacuum of 10-6 torr and allowed to cool to the desired temperature. The perylene was then evaporated over a period of one minute from a molybdenum boat at a distance of 10cm from the KCl. The perylene thin film was then backed with an amorphous layer of carbon and floated onto copper microscope grids.

Epitaxy and texture analysis of Bi-Sr-Ca-Cu-O thin films on (100) MgO using Transmission Electron Microscopy

1990 ◽  
Vol 48 (4) ◽  
pp. 68-69
Author(s):  
J. T. Sizemore ◽  
D. G. Schlom ◽  
Z. J. Chen ◽  
J. N. Eckstein ◽  
I. Bozovic ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Thin Films ◽  
Transmission Electron Microscopy ◽  
Critical Currents ◽  
Unit Cell ◽  
X Ray Diffraction ◽  
Cell Axis ◽  
Transmission Electron ◽  
Synthesis Procedure

Investigators observe large critical currents for superconducting thin films deposited epitaxially on single crystal substrates. The orientation of these films is often characterized by specifying the unit cell axis that is perpendicular to the substrate. This omits specifying the orientation of the other unit cell axes and grain boundary angles between grains of the thin film. Misorientation between grains of YBa2Cu3O7−δ decreases the critical current, even in those films that are c axis oriented. We presume that these results are similar for bismuth based superconductors and report the epitaxial orientations and textures observed in such films.Thin films of nominally Bi2Sr2CaCu2Ox were deposited on MgO using molecular beam epitaxy (MBE). These films were in situ grown (during growth oxygen was incorporated and the films were not oxygen post-annealed) and shuttering was used to encourage c axis growth. Other papers report the details of the synthesis procedure. The films were characterized using x-ray diffraction (XRD) and transmission electron microscopy (TEM).

scholarly journals The Domain and Microstructure of Resin-Bonded Magnets

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2849
Author(s):  
Marcin Jan Dośpiał
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Grain Size ◽  
Size Distribution ◽  
Domain Structure ◽  
Grain Size Distribution ◽  
Exchange Interactions ◽  
Force Microscopy ◽  
Transmission Electron ◽  
Scanning Electron

This paper presents domain and structure studies of bonded magnets made from nanocrystalline Nd-(Fe, Co)-B powder. The structure studies were investigated using scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), Mössbauer spectroscopy and X-ray diffractometry. On the basis of performed qualitative and quantitative phase composition studies, it was found that investigated alloy was mainly composed of Nd2(Fe-Co)14B hard magnetic phase (98 vol%) and a small amount of Nd1.1Fe4B4 paramagnetic phase (2 vol%). The best fit of grain size distribution was achieved for the lognormal function. The mean grain size determined from transmission electron microscopy (TEM) images on the basis of grain size distribution and diffraction pattern using the Bragg equation was about ≈130 nm. HRTEM images showed that over-stoichiometric Nd was mainly distributed on the grain boundaries as a thin amorphous border of 2 nm in width. The domain structure was investigated using a scanning electron microscope and metallographic light microscope, respectively, by Bitter and Kerr methods, and by magnetic force microscopy. Domain structure studies revealed that the observed domain structure had a labyrinth shape, which is typically observed in magnets, where strong exchange interactions between grains are present. The analysis of the domain structure in different states of magnetization revealed the dynamics of the reversal magnetization process.

Sign in / Sign up

Export Citation Format

Share Document