GaN layers re-grown on etched GaN templates by plasma assisted molecular beam epitaxy

2003 ◽  
Vol 798 ◽  
Author(s):  
L. He ◽  
J. Xie ◽  
F. Yun ◽  
A. A. Baski ◽  
H. Morkoç

ABSTRACTThe growth of high-quality GaN by plasma assisted molecular beam epitaxy (MBE) is challenging, in part due to the constraint of heteroepitaxy since GaN substrates are not yet commercially available and isotropic nature of growth. Despite the large lattice and thermal mismatch between sapphire and GaN, the former is still the most commonly used substrate for the GaN-based optical devices at present. In this paper, we demonstrate a re-growth technique to obtain an improved quality GaN by MBE on GaN template on sapphire where the grossly defective regions have been removed. This GaN template is formed by MBE growth of GaN followed by wet chemical etching to selectively remove the defective region. Improved quality GaN was re-grown on such a template under Ga rich conditions to a thickness of about 1 micron. After re-growth, the surface of GaN is atomically smooth with spiral features in the short range. The low temperature PL of the re-grown GaN is superior to those of MBE GaN films directly on sapphire. Atomic force microscopy (AFM) images reveal a two-dimensional re-growth initiating in regions free of extended defects. The results show that the selectively etched GaN on sapphire can be used as a good template to improve the quality of GaN.

Photonics ◽  
2021 ◽  
Vol 8 (6) ◽  
pp. 215
Author(s):  
Rajeev R. Kosireddy ◽  
Stephen T. Schaefer ◽  
Marko S. Milosavljevic ◽  
Shane R. Johnson

Three InAsSbBi samples are grown by molecular beam epitaxy at 400 °C on GaSb substrates with three different offcuts: (100) on-axis, (100) offcut 1° toward [011], and (100) offcut 4° toward [011]. The samples are investigated using X-ray diffraction, Nomarski optical microscopy, atomic force microscopy, transmission electron microscopy, and photoluminescence spectroscopy. The InAsSbBi layers are 210 nm thick, coherently strained, and show no observable defects. The substrate offcut is not observed to influence the structural and interface quality of the samples. Each sample exhibits small lateral variations in the Bi mole fraction, with the largest variation observed in the on-axis growth. Bismuth rich surface droplet features are observed on all samples. The surface droplets are isotropic on the on-axis sample and elongated along the [011¯] step edges on the 1° and 4° offcut samples. No significant change in optical quality with offcut angle is observed.


2006 ◽  
Vol 955 ◽  
Author(s):  
Huixin Xiu ◽  
Pedro MFJ Costa ◽  
Matthias Kauer ◽  
Tim M Smeeton ◽  
Stewart E Hooper ◽  
...  

ABSTRACTThis paper reports on the study of defects in p-type layers in III-nitride laser structures grown by molecular beam epitaxy. Characterization of the heterostructures was carried out using atomic force microscopy and transmission electron microscopy. The results show that a high density of extended defects – possibly inversion domains – exist in the p-type cladding layers of as-grown structures with either AlGaN/GaN superlattices or bulk AlGaN cladding layers. TEM analysis of operated and aged devices does not reveal any significant structural modification of the p-type material which might be the cause of deterioration in the lasing performance or failure.


1998 ◽  
Vol 512 ◽  
Author(s):  
N. Grandjean ◽  
M. Leroux ◽  
J. Massies ◽  
M. Mesrine ◽  
P. Lorenzini

ABSTRACTAmmonia as nitrogen precursor has been used to grow III-V nitrides by molecular beam epitaxy (MBE) on c-plane sapphire substrates. The efficiency of NH3 has been evaluated allowing the determination of the actual V/III flux ratio used during the GaN growth. The effects of the V/III ratio variation on the GaN layer properties have been investigated by photoluminescence (PL), Hall measurements, atomic force microscopy (AFM), and secondary ion mass spectroscopy (SIMS). It is found that a high V/III ratio leads to the best material quality. Optimized GaN thick buffer layers have been used to grow GaN/AlGaN quantum well (QW) heterostructures. Their PL spectra exhibit well resolved emission peaks for QW thicknesses varying from 3 to 15 monolayers. From the variation of the QW energies as a function of well width, a piezoelectric field of 450 kV/cm is deduced.


2016 ◽  
Vol 6 (1) ◽  
Author(s):  
Yong-Jin Cho ◽  
Alex Summerfield ◽  
Andrew Davies ◽  
Tin S. Cheng ◽  
Emily F. Smith ◽  
...  

Abstract We demonstrate direct epitaxial growth of high-quality hexagonal boron nitride (hBN) layers on graphite using high-temperature plasma-assisted molecular beam epitaxy. Atomic force microscopy reveals mono- and few-layer island growth, while conducting atomic force microscopy shows that the grown hBN has a resistance which increases exponentially with the number of layers, and has electrical properties comparable to exfoliated hBN. X-ray photoelectron spectroscopy, Raman microscopy and spectroscopic ellipsometry measurements on hBN confirm the formation of sp2-bonded hBN and a band gap of 5.9 ± 0.1 eV with no chemical intermixing with graphite. We also observe hexagonal moiré patterns with a period of 15 nm, consistent with the alignment of the hBN lattice and the graphite substrate.


2008 ◽  
Vol 1068 ◽  
Author(s):  
Jean-Christophe Moreno ◽  
Eric Frayssinet ◽  
Fabrice Semond ◽  
Jean Massies

ABSTRACTIn this work, we present a study of epitaxial Aluminium Nitride (AlN) for thin film bulk acoustic wave (BAW) applications. Molecular beam epitaxy (MBE) was used to perform high crystalline quality AlN thin films growth on different silicon substrate preparations. A morphological study was performed by atomic force microscopy (AFM) and scanning electron microscopy (SEM), while structural properties and acoustic wave speed were respectively assessed by X-ray diffraction and acoustic picoseconds.


1996 ◽  
Vol 452 ◽  
Author(s):  
W. H. Thompson ◽  
Z. Yamani ◽  
H. M. Nayfeh ◽  
M.-A. Hasan ◽  
J. E. Greene ◽  
...  

AbstractThe surface morphology of Ge grown on Si (001) and porous Si(001) by molecular beam epitaxy at 380 °C is examined using atomic force microscopy (AFM). For layer thicknesses of 30 nm, the surface shows islanding while still maintaining some of the underlying roughness of the surface of porous Si. For thicknesses in the 100 nm range, the surface roughness is not visible, but the islanding persists. Unlike the case of silicon where islands tend to merge and nearly disappear as the thickness of the deposited layer rises, we observe on the porous layer the persistence of the islands with no merging even for macroscopic thicknesses as large as 0.73 microns.


1994 ◽  
Vol 340 ◽  
Author(s):  
Art J. Nelson ◽  
M. Bode ◽  
G. Horner ◽  
K. Sinha ◽  
John Moreland

ABSTRACTEpitaxial growth of the ordered vacancy compound (OVC) CuIn3Se5 has been achieved on GaAs (100) by molecular beam epitaxy (MBE) from Cu2Se and In2Se3 sources. Electron probe microanalysis and X-ray diffraction have confirmed the composition for the 1-3-5 OVC phase and that the film is single crystal Culn3Se5 (100). Transmission electron microscopy (TEM) characterization of the material also showed it to be single crystalline. Structural defects in the layer consisted mainly of stacking faults. Photoluminescence (PL) measurements performed at 7.5 K indicate that the bandgap is 1.28 eV. Raman spectra reveal a strong polarized peak at 152 cm−1, which is believed to arise from the totally symmetric vibration of the Se atoms in the lattice. Atomic force microscopy reveals faceting in a preferred (100) orientation.


2011 ◽  
Vol 1295 ◽  
Author(s):  
Costel Constantin ◽  
Abhijit Chinchore ◽  
Arthur R. Smith

ABSTRACTThe combination of the molecular beam epitaxy growth method with the in-situ reflection high energy electron diffraction measurements currently offers unprecedented control of crystalline growth materials. We present here a stoichiometric study of MnxSc(1-x) [x = 0, 0.03, 0.05, 0.15, 0.25, 0.35, and 0.50] thin films grown on MgO(001) substrates with this growth method. Reflection high energy electron diffraction and atomic force microscopy measurements reveal alloy behavior for all of our samples. In addition, we found that samples Mn0.10Sc0.90 and Mn0.50Sc0.50 display surface self-assembled nanowires with a length/width ratio of ~ 800 – 2000.


Sign in / Sign up

Export Citation Format

Share Document