scholarly journals Selection of laser processing parameters for hot stamping tools based on mathematical planning of the experiment

2021 ◽  
pp. 37-40
Author(s):  
N. A. Chichenev ◽  
O. N. Chicheneva ◽  
A. O. Karfidov ◽  
A. N. Pashkov
Keyword(s):  
Laser Processing ◽  
Hot Stamping ◽  
Processing Parameters ◽  
Mathematical Planning ◽  
Selection Of

scholarly journals Characteristics of Cr-B Coatings Produced on Vanadis® 6 Tool Steel Using Laser Processing

Materials ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2621
Author(s):  
Aneta Bartkowska
Keyword(s):  
Corrosion Resistance ◽  
Tool Steel ◽  
Laser Processing ◽  
Chemical Elements ◽  
Steel Substrate ◽  
Processing Parameters ◽  
Beam Power ◽  
Laser Beam Power ◽  
High Microhardness ◽  
The Impact

The paper presents the results of a study of the microstructure, chemical composition, microhardness and corrosion resistance of Cr-B coatings produced on Vanadis 6 tool steel. In this study, chromium and boron were added to the steel surface using a laser alloying process. The main purpose of the study was to determine the impact of those chemical elements on surface properties. Chromium and boron as well as their mixtures were prepared in various proportions and then were applied on steel substrate in the form of precoat of 100 µm thickness. Depending on the type of precoat used and laser processing parameters, changes in microstructure and properties were observed. Coatings produced using precoat containing chromium and boron mixture were characterized by high microhardness (900 HV0.05–1300 HV0.005) while maintaining good corrosion resistance. It was also found that too low laser beam power contributed to the formation of cracks and porosity.

The Effect of Parameters of Laser Processing on the Morphology of Glaze Cladding

2012 ◽  
Vol 586 ◽  
pp. 265-268 ◽  
Author(s):  
Ji Wei Fan ◽  
Zhi Qiang Jiao ◽  
Xiao Peng Li ◽  
Hui Jun Zhao ◽  
Zhen Guo Zhang ◽  
...  
Keyword(s):  
Output Power ◽  
Processing Speed ◽  
Laser Processing ◽  
Ceramic Materials ◽  
Processing Parameters ◽  
Laser Technique ◽  
Experimental Conditions ◽  
Melted Zone

Laser processing ceramic materials is a new application of laser technique. This paper presents the study of laser processing parameters of glaze cladding. It found out that the parameters of laser processing affected the morphology of glaze cladding significantly. Within the experimental conditions, rise of output power or drop of processing speed can increase the depth of melted zone and the width of glaze cladding, vice versa.

Hot Stamping Processing Experiments of Quenchable Boron Steel

2008 ◽  
Vol 575-578 ◽  
pp. 299-304 ◽  
Author(s):  
Jun Bao ◽  
Zhong Wen Xing ◽  
Yu Ying Yang
Keyword(s):  
Heating Temperature ◽  
Hot Stamping ◽  
Cooling Water ◽  
High Strength ◽  
Processing Parameters ◽  
Boron Steel ◽  
Complicated Shape ◽  
Water Flow Velocity ◽  
Ultra High Strength Steel ◽  
Automotive Parts

The quenchable boron steel is a novel type of ultra high strength steel used for automotive parts so as to reduce the weight of the whole automobile. The hot stamping processing experiments for bending parts were studied. The influence of the hot stamping processing parameters, such as the heating temperature, the heat holding time and the cooling water flow velocity, on the mechanics properties and microstructure of the hot stamping parts is obtained. And then the optimal ranges of these parameters are determined, which provides a basis for the control of the hot stamping process applied in complicated shape parts’ production.

Deterministic Selection of Processing Parameters

1997 ◽  
Author(s):  
P. Armstrong ◽  
I. Scott ◽  
T. Brice ◽  
D. Ireson
Keyword(s):  
Processing Parameters ◽  
Selection Of

Effect of Laser Processing Parameters on Microhole Quality of Aluminium Nitride Ceramics

2021 ◽  
Vol 871 ◽  
pp. 277-283
Author(s):  
Chun Yan Yang ◽  
Yun Hao ◽  
Bozhe Wang ◽  
Hai Yuan ◽  
Liu Hui Li
Keyword(s):  
Laser Processing ◽  
Laser Power ◽  
Picosecond Laser ◽  
Scanning Speed ◽  
Processing Parameters ◽  
Recast Layer ◽  
Aluminium Nitride ◽  
Obvious Effect ◽  
Nitride Ceramics

A picosecond laser in spin-cutting mode was used to drill 500μm diameter microholes on 150μm thick aluminium nitride ceramic. The effects of laser processing parameters such as the laser power, scanning speed, and defocus amount on the microhole quality were studied. The results show that as the laser power increases, the inlet and outlet diameters of the holes increase, the taper decreases slightly, and the thickness of the recast layer decreases evidently. The scanning speed has no obvious effect on the diameter and taper of the hole; however, the hole can not be drilled through when the speed is too large. Positive defocus can effectively reduce the taper of the hole. Under 28.5W laser power, 400Hz frequency, 200mm/s scanning speed, and zero defocus amount conditions, high-quality microholes with a taper of 0.85° were obtained.

Effect of pulsed Nd:YAG laser processing parameters on surface properties of polyimide films

2019 ◽  
Vol 361 ◽  
pp. 102-111 ◽  
Author(s):  
Huilong Liu ◽  
Yong Tang ◽  
Yingxi Xie ◽  
Longsheng Lu ◽  
Zhenping Wan ◽  
...  
Keyword(s):  
Surface Properties ◽  
Nd:Yag Laser ◽  
Laser Processing ◽  
Processing Parameters ◽  
Polyimide Films ◽  
Pulsed Nd:Yag Laser
Sign in / Sign up

Export Citation Format

Share Document