scholarly journals Surface roughness characterization of stainless steel after laser assisted machining

Mechanik ◽  
2019 ◽  
Vol 92 (12) ◽  
pp. 827-829 ◽  
Author(s):  
Agata Felusiak ◽  
Martyna Wiciak-Pikuła ◽  
Tadeusz Chwalczuk ◽  
Piotr Kieruj ◽  
Paweł Twardowski
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Cutting Parameters ◽  
Cemented Carbide ◽  
Roughness Parameters ◽  
Laser Assisted Machining ◽  
Carbide Inserts ◽  
Cemented Carbide Inserts

The paper presents the analysis of the influence of laser assisted machining (LAM) on various parameters of surface roughness of stainless steel. The tests were carried out for cemented carbide inserts with varying cutting parameters. In most cases, a significant reduction in the roughness parameters was observed using LAM.

Deposition of Diamond Films on Smooth Surfaces of Cemented Carbide Inserts with Cobalt Boride Interlayers

2006 ◽  
Vol 315-316 ◽  
pp. 205-209
Author(s):  
Y. Wang ◽  
Y.P. Ma ◽  
Fang Hong Sun ◽  
Zhi Ming Zhang ◽  
Ming Chen
Keyword(s):  
Surface Roughness ◽  
Diamond Films ◽  
Fold Increase ◽  
Cemented Carbide ◽  
Widespread Application ◽  
Coated Tools ◽  
Key Factor ◽  
Cobalt Boride ◽  
Carbide Inserts ◽  
Cemented Carbide Inserts

Improving adhesion and surface roughness of diamond films on WC–Co substrate is the key factor of the widespread application of diamond coated tools. A new pretreatment method has been performed for smooth Co-cemented carbide inserts in order to lower the surface roughness of diamond films under the premise of good adhesion between diamond films and substrates. The effect of the new pretreatment on the adhesion of the diamond films is investigated. Research results show that the boronization pretreatment can effectively suppress cobalt diffusion to the surface and avoid catalytic effect of Co at high temperature. This new pretreatment can avoid the surface roughening of inserts and ensure the deposition of smooth diamond films. Investigation shows that the optimum boronization compounding is a powder mixture of 70%B4C+15.5%KBF4+1.5% La2O3+13%Na2CO3. Adhesion between substrates and diamond films is evaluated by Rockwell A indentation tests and the cutting performance of the diamond-coated tools is investigated by the cutting tests. Diamond films on smooth cemented carbide inserts with cobalt boride interlayer have high adhesive strength and low surface roughness. Diamond-coated tools with boronization pretreatment have a 5-fold increase in tool life compared with untreated ones.

Effect of Substrate Bias and Coating Thickness on the Properties of nc-AlCrN/a-SixNy Hard Coating and Determination of Cutting Parameters

2017 ◽  
Vol 261 ◽  
pp. 229-236 ◽  
Author(s):  
Tomáš Vopát ◽  
Marián Haršáni ◽  
Marcel Kuruc ◽  
Vladimír Šimna ◽  
Rudolf Zaujec ◽  
...  
Keyword(s):  
Cutting Speed ◽  
Cutting Parameters ◽  
Cemented Carbide ◽  
Depth Of Cut ◽  
Substrate Bias ◽  
Substrate Bias Voltage ◽  
Coated Cemented Carbide ◽  
Carbide Inserts ◽  
Cemented Carbide Inserts

Nitride hard coatings Al25.5Cr21Si3.5N were deposited on WC-Co substrates with a different thickness and a negative substrate bias voltage by the LAteral Rotating Cathodes Arc technology. The nanoindentation tests were performed for analysis of AlCrSiN coatings in order to determine the most promising combination of parameters for subsequent machining. On the basis of results of nanohardness measurement and Ratio H/E*, which represents the resistance to plastic deformation and cracking, deposition conditions were selected for coating of turning cemented carbide inserts. For the evaluation of coating adhesion to substrate, Mercedes adhesion test was used. Chip forming tests and long-term tool life tests were performed for determination of cutting parameters (cutting speed, feed rate and depth of cut) for AlCrSiN coated cemented carbide inserts when machining austenitic stainless steel material.

The Effect of Substrate Surface Characteristics on AIP PVD Coating of Cemented Carbide Inserts and Their Cutting Performance

2007 ◽  
Vol 534-536 ◽  
pp. 1241-1244 ◽  
Author(s):  
Dong Gil Ahn ◽  
Kern Woo Lee ◽  
Joo Wan Lee ◽  
Moshe Sharon
Keyword(s):  
Surface Roughness ◽  
Surface Treatment ◽  
Substrate Surface ◽  
Surface Characteristics ◽  
Cutting Performance ◽  
Cemented Carbide ◽  
Physical Treatment ◽  
Pvd Coating ◽  
Carbide Inserts ◽  
Cemented Carbide Inserts

The effects of substrate surface treatment on TiAlN PVD coating on submicron cemented carbide was investigated. Surface roughness and morphology were improved by physical treatment such as micro blasting, brush lapping and plasma etching with decreased Co content in the surface layer. The Co content in the surface does not seem to affect coating adhesion or the quality considerably. The smoother surface induced by the surface treatment improved TiAlN adhesion and surface roughness. The insert treated by blasting and lapping before coating showed a better cutting performance than those with ultrasonic treatment. It was concluded that the substrate surface characteristics are closely related to the performance of the TiAlN coated inserts.

Studying The Effect of a New Mixed Cutting Fluid on Surface Roughness

2020 ◽  
Vol 38 (11A) ◽  
pp. 1593-1601
Author(s):  
Mohammed H. Shaker ◽  
Salah K. Jawad ◽  
Maan A. Tawfiq
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Cutting Parameters ◽  
Machining Process ◽  
Cutting Fluid ◽  
Depth Of Cut ◽  
Cutting Fluids ◽  
Machining Processes ◽  
Dry Cutting ◽  
Cutting Speeds

This research studied the influence of cutting fluids and cutting parameters on the surface roughness for stainless steel worked by turning machine in dry and wet cutting cases. The work was done with different cutting speeds, and feed rates with a fixed depth of cutting. During the machining process, heat was generated and effects of higher surface roughness of work material. In this study, the effects of some cutting fluids, and dry cutting on surface roughness have been examined in turning of AISI316 stainless steel material. Sodium Lauryl Ether Sulfate (SLES) instead of other soluble oils has been used and compared to dry machining processes. Experiments have been performed at four cutting speeds (60, 95, 155, 240) m/min, feed rates (0.065, 0.08, 0.096, 0.114) mm/rev. and constant depth of cut (0.5) mm. The amount of decrease in Ra after the used suggested mixture arrived at (0.21µm), while Ra exceeded (1µm) in case of soluble oils This means the suggested mixture gave the best results of lubricating properties than other cases.

scholarly journals Post-Processing and Surface Characterization of Additively Manufactured Stainless Steel 316L Lattice: Implications for BioMedical Use

Materials ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1376
Author(s):  
Alex Quok An Teo ◽  
Lina Yan ◽  
Akshay Chaudhari ◽  
Gavin Kane O’Neill
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Surface Characterization ◽  
High Surface ◽  
Surface Characteristics ◽  
Post Processing ◽  
Stainless Steel 316L ◽  
Processing Methods ◽  
Particulate Debris

Additive manufacturing of stainless steel is becoming increasingly accessible, allowing for the customisation of structure and surface characteristics; there is little guidance for the post-processing of these metals. We carried out this study to ascertain the effects of various combinations of post-processing methods on the surface of an additively manufactured stainless steel 316L lattice. We also characterized the nature of residual surface particles found after these processes via energy-dispersive X-ray spectroscopy. Finally, we measured the surface roughness of the post-processing lattices via digital microscopy. The native lattices had a predictably high surface roughness from partially molten particles. Sandblasting effectively removed this but damaged the surface, introducing a peel-off layer, as well as leaving surface residue from the glass beads used. The addition of either abrasive polishing or electropolishing removed the peel-off layer but introduced other surface deficiencies making it more susceptible to corrosion. Finally, when electropolishing was performed after the above processes, there was a significant reduction in residual surface particles. The constitution of the particulate debris as well as the lattice surface roughness following each post-processing method varied, with potential implications for clinical use. The work provides a good base for future development of post-processing methods for additively manufactured stainless steel.

Effects of Insert Nose Radius and Processing Cutting Parameter on the Surface Roughness of Aisi 316 Stainless Steel

2010 ◽  
Vol 447-448 ◽  
pp. 51-54
Author(s):  
Mohd Fazuri Abdullah ◽  
Muhammad Ilman Hakimi Chua Abdullah ◽  
Abu Bakar Sulong ◽  
Jaharah A. Ghani
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Surface Finish ◽  
Feed Rate ◽  
Cutting Speed ◽  
Chip Thickness ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Nose Radius ◽  
Aisi 316

The effects of different cutting parameters, insert nose radius, cutting speed and feed rates on the surface quality of the stainless steel to be use in medical application. Stainless steel AISI 316 had been machined with three different nose radiuses (0.4 mm 0.8 mm, and 1.2mm), three different cutting speeds (100, 130, 170 m/min) and feed rates (0.1, 0.125, 0.16 mm/rev) while depth of cut keep constant at (0.4 mm). It is seen that the insert nose radius, feed rates, and cutting speed have different effect on the surface roughness. The minimum average surface roughness (0.225µm) has been measured using the nose radius insert (1.2 mm) at lowest feed rate (0.1 mm/rev). The highest surface roughness (1.838µm) has been measured with nose radius insert (0.4 mm) at highest feed rate (0.16 mm/rev). The analysis of ANOVA showed the cutting speed is not dominant in processing for the fine surface finish compared with feed rate and nose radius. Conclusion, surface roughness is decreasing with decreasing of the feed rate. High nose radius produce better surface finish than small nose radius because of the maximum uncut chip thickness decreases with increase of nose radius.

Evaluation of Process Parameters in Machining of AA6063 Alloy

2018 ◽  
Vol 1148 ◽  
pp. 109-114
Author(s):  
M. Balaji ◽  
C.H. Nagaraju ◽  
V.U.S. Vara Prasad ◽  
R. Kalyani ◽  
B. Avinash
Keyword(s):  
Surface Roughness ◽  
Regression Analysis ◽  
Process Parameters ◽  
Single Channel ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Roughness Parameters ◽  
Surface Roughness Parameters ◽  
Aa6063 Alloy

The main aim of this work is to analyse the significance of cutting parameters on surface roughness and spindle vibrations while machining the AA6063 alloy. The turning experiments were carried out on a CNC lathe with a constant spindle speed of 1000rpm using carbide tool inserts coated with Tic. The cutting speed, feed rate and depth of cut are chosen as process parameters whose values are varied in between 73.51m/min to 94.24m/min, 0.02 to 0.04 mm/rev and 0.25 to 0.45 mm respectively. For each experiment, the surface roughness parameters and the amplitude plots have been noted for analysis. The output data include surface roughness parameters (Ra,Rq,Rz) measured using Talysurf and vibration parameter as vibration amplitude (mm/sec) at the front end of the spindle in transverse direction using single channel spectrum analyzer (FFT).With the collected data Regression analysis is also performed for finding the optimum parameters. The results show that significant variation of surface irregularities and vibration amplitudes were observed with cutting speed and feed. The optimum cutting speed and feed from the regression analysis were 77.0697m/min and 0.0253mm/rev. for the minimum output parameters. No significant effect of depth of cut on output parameters is identified.

Sign in / Sign up

Export Citation Format

Share Document