scholarly journals INFLUENCE OF SHAPE OF PRESSURE VESSEL SHELL ON BOLT WORKING LOAD AND TIGHTNESS

2021 ◽  
Vol 2021 (6) ◽  
pp. 5448-5451
Author(s):  
JIRI ZACAL ◽  
◽  
JAN PAVLIK ◽  
IVANA KUNZOVA ◽  
◽  
...  
Keyword(s):  
Pressure Vessel ◽  
Pressure Vessels ◽  
Pressure Chamber ◽  
Engineering Practice ◽  
Specific Load ◽  
Load Conditions

The area of flange joints with gasket includes many types of pressure vessels, which are mainly defined by the purpose of use and specific load conditions. These differences in definitions caused the existence of many types of pressure vessels with different shell shapes. Calculations of basic shapes are defined by standards. However, in some fields of engineering practice, these shapes are atypical. The article discusses the issue of circular sealed flange joints with a nonstandard shape of the pressure chamber shells. The aim of this article is to describe influence of shape of pressure vessel shell on bolt working load and the final tightness of the sealed joint using FEM.

A Case for New Low Pressure Vessel (LPV) Codes for Design Pressures Below 15 psi (100 kPA)

2021 ◽  
Author(s):  
Barry Millet ◽  
Kaveh Ebrahimi ◽  
James Lu ◽  
Donald Spencer
Keyword(s):  
Pressure Vessel ◽  
Power Plants ◽  
Low Pressure ◽  
Pressure Vessels ◽  
Engineering Practice ◽  
Element Analysis ◽  
Gas Treatment ◽  
Food And Beverage ◽  
Asme Code ◽  
Design Pressure

Abstract Today the ASME Boiler and Pressure Vessel Code Section VIII (ASME Code) covers pressure vessels for design pressure above 15 psi (100 kPa) but not for design pressures below 15 psi. Manufacturers of pressure vessels under 10ft (3048mm) and with design pressure under 15 psi (100 kPa) design to the ASME Code but do not stamp them. The ASME Code is explicit in not allowing this. Manufacturers of low pressure vessels over 10 ft (3048 mm) in diameter, design and built to “good engineering practice” using Finite Element Analysis, the ASME Code, API and the AISC Manual of Steel Construction. This paper provides an overview of these existing codes, standards with their methods for design, fabrication and testing then provides an outline of a Code with two classes of low pressure vessels (LPV). The audience for the smaller pressure vessels would be small batch chemical, pharmaceutical, food, and beverage processing facilities who require small near atmospheric pressure vessels. The audience for the larger pressure vessels would be power plants, refineries, chemical plant, steel mills and concrete plants flue gas treatment and CO2 sequestration of exhaust products.

Stress Field Around a Large Opening in a Pressure Vessel During a Major Repair

2009 ◽  
Author(s):  
Erik Garrido ◽  
Euro Casanova
Keyword(s):  
Pressure Vessel ◽  
New Technologies ◽  
Mechanical Design ◽  
General Purpose ◽  
Pressure Vessels ◽  
Mechanical Equipment ◽  
Stress Distributions ◽  
Large Opening ◽  
Von Mises ◽  
Case Basis

It is a regular practice in the oil industry to modify mechanical equipment to incorporate new technologies and to optimize production. In the case of pressure vessels, it is occasionally required to cut large openings in their walls in order to have access to the interior part of the equipment for executing modifications. This cutting process produces temporary loads, which were obviously not considered in the original mechanical design. Up to now, there is not a general purpose specification for approaching the assessments of stress levels once a large opening in a vertical pressure vessel has been made. Therefore stress distributions around large openings are analyzed on a case-by-case basis without a reference scheme. This work studies the distribution of the von Mises equivalent stresses around a large opening in FCC Regenerators during internal cyclone replacement, which is a frequently required practice for this kind of equipment. A finite element parametric model was developed in ANSYS, and both numerical results and illustrating figures are presented.

Effect of Carbide Content on Temper Embrittlement of 2.25Cr1Mo Steel

2016 ◽  
Author(s):  
Yian Wang ◽  
Guoshan Xie ◽  
Zheng Zhang ◽  
Xiaolong Qian ◽  
Yufeng Zhou ◽  
...  
Keyword(s):  
High Temperature ◽  
Pressure Vessel ◽  
High Stress ◽  
Temper Embrittlement ◽  
Damage Mechanism ◽  
Pressure Vessels ◽  
Nondestructive Method ◽  
Operating Conditions ◽  
Low Alloy Steels ◽  
Carbide Content

Temper embrittlement is a common damage mechanism of pressure vessels in the chemical and petrochemical industry serviced in high temperature, which results in the reduction of roughness due to metallurgical change in some low alloy steels. Pressure vessels that are temper embrittled may be susceptible to brittle fracture under certain operating conditions which cause high stress by thermal gradients, e.g., during start-up and shutdown. 2.25Cr1-Mo steel is widely used to make hydrogenation reactor due to its superior combination of high mechanical strength, good weldability, excellent high temperature hydrogen attack (HTHA) and oxidation-resistance. However, 2.25Cr-1Mo steel is particularly susceptible to temper embrittlement. In this paper, the effect of carbide on temper embrittlement of 2.25Cr-1Mo steel was investigated. Mechanical properties and the ductile-brittle transition temperature (DBTT) of 2.25Cr-1Mo steel were measured by tensile test and impact test. The tests were performed at two positions (base metal and weld metal) and three states (original, step cooling treated and in-service for a hundred thousand hours). The content and distribution of carbides were analyzed by scanning electron microscope (SEM). The content of Cr and Mo elements in carbide was measured by energy dispersive X-ray analysis (EDS). The results showed that the embrittlement could increase the strength and reduce the plasticity. Higher carbide contents appear to be responsible for the higher DBTT. The in-service 2.25Cr-1Mo steel showed the highest DBTT and carbide content, followed by step cooling treated 2.25Cr-1Mo steel, while the as-received 2.25Cr-1Mo steel has the minimum DBTT and carbide content. At the same time, the Cr and Mo contents in carbide increased with the increasing of DBTT. It is well known that the specimen analyzed by SEM is very small in size, sampling SEM specimen is convenient and nondestructive to pressure vessel. Therefore, the relationship between DBTT and the content of carbide offers a feasible nondestructive method for quantitative measuring the temper embrittlement of 2.25Cr-1Mo steel pressure vessel.

A Study on Fatigue Life Evaluation of Pressure Vessel Made of ASME SA240-316L Material Using Numerical Analysis

2019 ◽  
Vol 893 ◽  
pp. 1-5 ◽  
Author(s):  
Eui Soo Kim
Keyword(s):  
Finite Element ◽  
Fatigue Life ◽  
Pressure Vessel ◽  
Life Prediction ◽  
Pressure Vessels ◽  
Physical Damage ◽  
Element Analysis ◽  
Internal Damage ◽  
Life Evaluation ◽  
Fatigue Life Evaluation

Pressure vessels are subjected to repeated loads during use and charging, which can causefine physical damage even in the elastic region. If the load is repeated under stress conditions belowthe yield strength, internal damage accumulates. Fatigue life evaluation of the structure of thepressure vessel using finite element analysis (FEA) is used to evaluate the life cycle of the structuraldesign based on finite element method (FEM) technology. This technique is more advanced thanfatigue life prediction that uses relational equations. This study describes fatigue analysis to predictthe fatigue life of a pressure vessel using stress data obtained from FEA. The life prediction results areuseful for improving the component design at a very early development stage. The fatigue life of thepressure vessel is calculated for each node on the model, and cumulative damage theory is used tocalculate the fatigue life. Then, the fatigue life is calculated from this information using the FEanalysis software ADINA and the fatigue life calculation program WINLIFE.

Fatigue and Burst Analysis of Hy-140(T) Steel Pressure Vessels

1970 ◽  
Vol 92 (1) ◽  
pp. 11-16 ◽  
Author(s):  
J. M. Barsom ◽  
S. T. Rolfe
Keyword(s):  
Yield Strength ◽  
Pressure Vessel ◽  
Low Cycle Fatigue ◽  
High Strength Steels ◽  
High Strength ◽  
Fatigue Tests ◽  
Pressure Vessels ◽  
High Yield ◽  
Corrosion Properties ◽  
Burst Analysis

Increasing use of high-strength steels in pressure-vessel design has resulted from emphasis on decreasing the weight of pressure vessels for certain applications. To demonstrate the suitability of a 140-ksi yield strength steel for use in unwelded pressure vessels, HY-140(T)—a quenched and tempered 5Ni-Cr-Mo-V steel—was fabricated and subjected to various burst and fatigue tests, as well as to various laboratory tests. In general, results of the investigation indicated very good tensile, Charpy, Nil Ductility Transition Temperature (NDT), low-cycle fatigue, and stress-corrosion properties of HY-140(T) steels, as well as very good burst tests results, in comparison with existing high-yield strength pressure-vessel steels. The results also indicate that the HY-140(T) steel should be an excellent material for its originally designed purpose, Naval hull applications.

Failure Probability Assessment for a Boiling Water Reactor Pressure Vessel Under Low Temperature Over-Pressure Event

2012 ◽  
Author(s):  
Hsoung-Wei Chou ◽  
Chin-Cheng Huang ◽  
Bo-Yi Chen ◽  
Hsien-Chou Lin ◽  
Ru-Feng Liu
Keyword(s):  
Low Temperature ◽  
Failure Probability ◽  
Pressure Vessel ◽  
Fracture Probability ◽  
Pressure Vessels ◽  
Reactor Pressure Vessel ◽  
Boiling Water ◽  
Boiling Water Reactor ◽  
Water Reactor ◽  
Reactor Pressure

The fracture probability of a boiling water reactor pressure vessel for a domestic nuclear power plant in Taiwan has been numerically analyzed using an advanced version of ORNL’s FAVOR code. First, a model of the vessel beltline region, which includes all shell welds and plates, is built for the FAVOR code based on the plant specific parameters of the reactor pressure vessel. Then, a novel flaw model which describes the flaw types of surface breaking flaws, embedded weld flaws and embedded plate flaws are simulated along both inner and outer vessel walls. When conducting the fracture probability analyses, a transient low temperature over-pressure event, which has previously been shown to be the most severe challenge to the integrity of boiling water reactor pressure vessels, is considered as the loading condition. It is found that the fracture occurs in the fusion-line area of axial welds, but with only an insignificant failure probability. The low through-wall cracking frequency indicates that the analyzed reactor pressure vessel maintains sufficient stability until either the end-of-license or for doubling of the present license of operation.

The Fatigue Analysis of Pressure Vessels Based on Workbench

2012 ◽  
Vol 550-553 ◽  
pp. 3082-3087
Author(s):  
Xing Ye Su ◽  
Qin Li ◽  
Hong Mei Wang
Keyword(s):  
Fatigue Failure ◽  
Chemical Industry ◽  
Pressure Vessel ◽  
Petrochemical Industry ◽  
Rapid Development ◽  
Fatigue Analysis ◽  
Pressure Vessels ◽  
Operation Condition ◽  
Key Steps

With the rapid development of petrochemical industry, the operation condition of pressure vessels under the alternating load was increasing and the probability of fatigue failure was also on the rise. As a result, pressure vessel fatigue analysis is gaining the designer's attention. This paper describes the key steps and techniques of the fatigue analysis of pressure vessel based on Workbench platform using the lock hopper of the coal chemical industry as an example.

A Study of Nozzles in Pressure Vessels under Pressure Fatigue Loading

1967 ◽  
Vol 182 (1) ◽  
pp. 657-684 ◽  
Author(s):  
J. Spence ◽  
W. B. Carlson
Keyword(s):  
Fatigue Life ◽  
Mild Steel ◽  
Pressure Vessel ◽  
Special Interest ◽  
Maximum Stress ◽  
Fatigue Loading ◽  
Fatigue Tests ◽  
Pressure Vessels ◽  
Full Size

Nozzles in cylindrical vessels have been of special interest to designers for some time and have offered a field of activity for many research workers. This paper presents some static and fatigue tests on five designs of full size pressure vessel nozzles manufactured in two materials. Supporting and other published work is reviewed showing that on the basis of the same maximum stress mild steel vessels give the same fatigue life as low alloy vessels. When compared on the basis of current codes it is shown that mild steel vessels may have five to ten times the fatigue life of low alloy vessels unless special precautions are taken.

A Noncyclic Method for Determination of Accumulated Strain in Stainless Steel 304 Pressure Vessels

2014 ◽  
Vol 136 (6) ◽  
Author(s):  
Gongfeng Jiang ◽  
Gang Chen ◽  
Liang Sun ◽  
Yiliang Zhang ◽  
Xiaoliang Jia ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Internal Pressure ◽  
Pressure Vessel ◽  
Peak Stress ◽  
Pressure Vessels ◽  
Experimental Results ◽  
Elastic Domain ◽  
Ratcheting Strain ◽  
Stainless Steel 304 ◽  
Accumulated Strain

Experimental results of uniaxial ratcheting tests for stainless steel 304 (SS304) under stress-controlled condition at room temperature showed that the elastic domain defined in this paper expands with accumulation of plastic strain. Both ratcheting strain and viscoplastic strain rates reduce with the increase of elastic domain, and the total strain will be saturated finally. If the saturated strain and corresponded peak stress of different experimental results under the stress ratio R ≥ 0 are plotted, a curve demonstrating the material shakedown states of SS304 can be constituted. Using this curve, the accumulated strain in a pressure vessel subjected to cyclic internal pressure can be determined by only an elastic-plastic analysis, and without the cycle-by-cycle analysis. Meanwhile, a physical experiment of a thin-walled pressure vessel subjected to cyclic internal pressure has been carried out to verify the feasibility and effectiveness of this noncyclic method. By comparison, the accumulated strains evaluated by the noncyclic method agreed well with those obtained from the experiments. The noncyclic method is simpler and more practical than the cycle-by-cycle method for engineering design.

Safety Assessment of Long Term Serviced Pressure Vessels: A Case Study of Typical Refining and Chemical Plants in China

2021 ◽  
Author(s):  
Zhiyuan Han ◽  
Guoshan Xie ◽  
Haiyi Jiang ◽  
Xiaowei Li
Keyword(s):  
Pressure Vessel ◽  
Safety Assessment ◽  
Failure Modes ◽  
Pressure Vessels ◽  
Time Dependent ◽  
Chemical Plants ◽  
Safety Specification ◽  
Detailed Assessment

Abstract The safety and risk of the long term serviced pressure vessels, especially which serviced more than 20 years, has become one of the most concerned issues in refining and chemical industry and government safety supervision in China. According to the Chinese pressure vessel safety specification TSG 21-2016 “Supervision Regulation on Safety Technology for Stationary Pressure Vessel”, if necessary, safety assessment should be performed for the pressure vessel which reaches the design service life or exceeds 20 years without a definite design life. However, the safety and risk conditions of most pressure vessels have little changes after long term serviced because their failure modes are time-independent. Thus the key problem is to identify the devices with the time-dependent failure modes and assess them based on the failure modes. This study provided a case study on 16 typical refining and chemical plants including 1870 pressure vessels serviced more than 20 years. The quantitative risk and damage mechanisms were calculated based on API 581, the time-dependent and time-independent failure modes were identified, and the typical pressure vessels were assessed based on API 579. Taking the high pressure hydrogenation plant as an example, this study gave the detailed assessment results and conclusions. The results and suggestions in this study are essential for the safety supervision and extending life of long term serviced pressure vessels in China.

Sign in / Sign up

Export Citation Format

Share Document