Investigation of the Ballistic Descent Mode for a Maneuverable Lander to the Venus Surface

2020 ◽  
pp. 42-60
Author(s):  
A.V. Kosenkova ◽  
V.E. Minenko ◽  
D.N. Agafonov
Keyword(s):  
Body Type ◽  
Long Period ◽  
Landing Module ◽  
Descent Trajectory ◽  
Drag Ratio ◽  
Lift To Drag Ratio ◽  
Venusian Atmosphere ◽  
Selection Of ◽  
Dense Atmosphere

At present, various projects to continue fundamental investigations of Venus are considered in Russia and abroad. It means that the issue of developing a landing module to reach the surface of the planet becomes topical, as the module might provide access to the regions most attractive in terms of research. We propose to use a landing module of the lifting body type, which, as compared to a ballistic class module, is not unacceptably complicated in terms of design and at the same time features a lift-to-drag ratio adequate for solving manoeuvring problems arising in the process of descent into the Venusian atmosphere to reach the target landing area. We consider potential descent trajectories available to a landing module of this type, including the possibility of performing a maximum lateral manoeuvre; we took into consideration its long-period trajectories characterised by multiple re-entries into the dense atmosphere and compared these trajectories to the descent trajectory of a conventional ballistic class landing module. We show that using a manoeuvrable craft expands the selection of potential landing regions, as well as reduces loads and broadens the scope of scientific problems to be solved and studies to be undertaken

Gurney flap scaling for optimum lift-to-drag ratio

AIAA Journal ◽  
1997 ◽  
Vol 35 ◽  
pp. 1888-1890 ◽  
Author(s):  
Philippe Giguere ◽  
Guy Dumas ◽  
Jean Lemay
Keyword(s):  
Gurney Flap ◽  
Drag Ratio ◽  
Lift To Drag Ratio

scholarly journals A Parametric Study of Trailing Edge Flap Implementation on Three Different Airfoils Through an Artificial Neuronal Network

Symmetry ◽  
2020 ◽  
Vol 12 (5) ◽  
pp. 828
Author(s):  
Igor Rodriguez-Eguia ◽  
Iñigo Errasti ◽  
Unai Fernandez-Gamiz ◽  
Jesús María Blanco ◽  
Ekaitz Zulueta ◽  
...  
Keyword(s):  
Aerodynamic Coefficients ◽  
Trailing Edge ◽  
High Lift ◽  
Trailing Edge Flaps ◽  
Artificial Neural Network Ann ◽  
Lift And Drag ◽  
Artificial Neuronal Network ◽  
Naca 0012 ◽  
Drag Ratio ◽  
Lift To Drag Ratio

Trailing edge flaps (TEFs) are high-lift devices that generate changes in the lift and drag coefficients of an airfoil. A large number of 2D simulations are performed in this study, in order to measure these changes in aerodynamic coefficients and to analyze them for a given Reynolds number. Three different airfoils, namely NACA 0012, NACA 64(3)-618, and S810, are studied in relation to three combinations of the following parameters: angle of attack, flap angle (deflection), and flaplength. Results are in concordance with the aerodynamic results expected when studying a TEF on an airfoil, showing the effect exerted by the three parameters on both aerodynamic coefficients lift and drag. Depending on whether the airfoil flap is deployed on either the pressure zone or the suction zone, the lift-to-drag ratio, CL/CD, will increase or decrease, respectively. Besides, the use of a larger flap length will increase the higher values and decrease the lower values of the CL/CD ratio. In addition, an artificial neural network (ANN) based prediction model for aerodynamic forces was built through the results obtained from the research.

scholarly journals Fluid–structure interaction simulation on flight performance of a dragonfly wing under different pterostigma weights

2021 ◽  
Vol 37 ◽  
pp. 216-229
Author(s):  
Yung Jeh Chu ◽  
Poo Balan Ganesan ◽  
Mohamad Azlin Ali
Keyword(s):  
Optimization Design ◽  
Fluid Structure Interaction ◽  
Spatial Location ◽  
Fluid Structure ◽  
Structure Interaction ◽  
Dragonfly Wing ◽  
Interaction Simulation ◽  
Wing Performance ◽  
Drag Ratio ◽  
Lift To Drag Ratio

Abstract The dragonfly wings provide insights for designing an efficient biomimetic micro air vehicle (BMAV). In this regard, this study focuses on investigating the effect of the pterostigma weight loading and its spatial location on the forewings of dragonfly by using the fluid–structure interaction simulation. This study also investigates the effect of change in the wing elasticity and density on the wing performance. The forewing, which mimics the real dragonfly wing, is flat with a 47.5 mm span and a 0.4 mm thickness. The wing was set to cruise at 3 m/s with a constant flapping motion at a frequency of 25 Hz. This study shows that a small increase of pterostigma loading (11% of wing weight) at the tip of the wing significantly improves the lift to drag ratio, CL/CD, which has 129.16% increment in comparison with no loading. The lift to drag ratio depends on the pterostigma location, pterostigma loading, elastic modulus and density. The results of this study can be used as a reference in future BMAV wing optimization design.

Aerodynamic study of single corrugated variable-camber morphing aerofoil concept

2021 ◽  
pp. 1-29
Author(s):  
K. Dhileep ◽  
D. Kumar ◽  
P.N. Gautham Vigneswar ◽  
P. Soni ◽  
S. Ghosh ◽  
...  
Keyword(s):  
Finite Volume ◽  
Interpolation Method ◽  
Beam Theory ◽  
Small Deformation ◽  
Aerodynamic Characteristics ◽  
Ansys Fluent ◽  
Aerodynamic Efficiency ◽  
Finite Element Software ◽  
Drag Ratio ◽  
Lift To Drag Ratio

Abstract Camber morphing is an effective way to control the lift generated by any aerofoil and potentially improve the range (as measured by the lift-to-drag ratio) and endurance (as measured by $C_l^{3/2}/C_d$ ). This can be especially useful for fixed-wing Unmanned Aerial Vehicles (UAVs) undergoing different flying manoeuvres and flight phases. This work investigates the aerodynamic characteristics of the NACA0012 aerofoil morphed using a Single Corrugated Variable-Camber (SCVC) morphing approach. Structural analysis and morphed shapes are obtained based on small-deformation beam theory using chain calculations and validated using finite-element software. The aerofoil is then reconstructed from the camber line using a Radial Basis Function (RBF)-based interpolation method (J.H.S. Fincham and M.I. Friswell, “Aerodynamic optimisation of a camber morphing aerofoil,” Aerosp. Sci. Technol., 2015). The aerodynamic analysis is done by employing two different finite-volume solvers (OpenFOAM and ANSYS-Fluent) and a panel method code (XFoil). Results reveal that the aerodynamic coefficients predicted by the two finite-volume solvers using a fully turbulent flow assumption are similar but differ from those predicted by XFoil. The aerodynamic efficiency and endurance factor of morphed aerofoils indicate that morphing is beneficial at moderate to high lift requirements. Further, the optimal morphing angle increases with an increase in the required lift. Finally, it is observed for a fixed angle-of-attack that an optimum morphing angle exists for which the aerodynamic efficiency becomes maximum.

Hydrodynamic Evaluation of a Generic Sail Used in an Innovative Prawn-Trawl Otter Board

2015 ◽  
Author(s):  
Cheslav Balash ◽  
David Sterling ◽  
Matt Broadhurst ◽  
Arno Dubois ◽  
Morgan Behrel
Keyword(s):  
Degrees Of Freedom ◽  
Design Feature ◽  
Hydrodynamic Characteristics ◽  
Flat Plates ◽  
Successful Operation ◽  
Six Degrees Of Freedom ◽  
Recent Innovation ◽  
Hydrodynamic Evaluation ◽  
Drag Ratio ◽  
Lift To Drag Ratio

In prawn-trawling operations, otter boards provide the horizontal force required to maintain net openings, and are typically low aspect ratio (∼0.5) flat plates operating on the seabed at high angles of attack (AOA; 35–40°). Such characteristics cause otter boards to account for up to 30% of the total trawling resistance, including that from the vessel. A recent innovation is the batwing otter board, which is designed to spread trawls with substantially less towing resistance and benthic impacts. A key design feature is the use of a sail, instead of a flat plate, as the hydrodynamic foil. The superior drag and benthic performance of the batwing is achieved by (i) successful operation at an AOA of ∼20° and (ii) having the heavy sea floor contact shoe in line with the direction of tow. This study investigated the hydrodynamic characteristics of a generic sail by varying its twist and camber, to identify optimal settings for maximum spreading efficiency and stability. Loads in six degrees of freedom were measured at AOAs between 0 and 40° in a flume tank at a constant flow velocity, and with five combinations of twist and camber. The results showed that for the studied sail, the design AOA (20°) provides a suitable compromise between greater efficiency (occurring at lower AOAs) and greater effectiveness (occurring at higher AOAs). At optimum settings (20°, medium camber and twist), a lift-to-drag ratio >3 was achieved, which is ∼3 times more than that of contemporary prawn-trawling otter boards. Such a result implies relative drag reductions of 10–20% for trawling systems, depending on the rig configuration.

scholarly journals Review of space vehicle control and guidance methods at atmosphere reentry

2021 ◽  
pp. 1-20
Author(s):  
Alexander Sergeevich Samotokhin
Keyword(s):  
Space Vehicle ◽  
Vehicle Control ◽  
Control Methods ◽  
The Moon ◽  
Reentry Vehicles ◽  
Drag Ratio ◽  
Lift To Drag Ratio

Review of control methods for statically stable reentry vehicles with low lift-to-drag ratio at returning from the Moon is presented. We are considering algorithms that have been used in Soviet and American Moon programs, as well as advanced algorithms that now are developed. General trends of advanced domestic and foreign methods are determined.

scholarly journals Aerodynamic and Vibration Characteristics of the Micro-Octocopter at Low Reynolds Number

2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Xiaohua Zou ◽  
Mingsheng Ling ◽  
Wenzheng Zhai
Keyword(s):  
Reynolds Number ◽  
Load Capacity ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Aerodynamic Characteristics ◽  
Vibration Characteristics ◽  
Low Reynolds ◽  
Vibration Performance ◽  
Drag Ratio ◽  
Lift To Drag Ratio

With the development of flight technology, the need for stable aerodynamic and vibration performance of the aircraft in the civil and military fields has gradually increased. In this case, the requirements for aerodynamic and vibration characteristics of the aircraft have also been strengthened. The existing four-rotor aircraft carries limited airborne equipment and payload, while the current eight-rotor aircraft adopts a plane layout. The size of the propeller is generally fixed, including the load capacity. The upper and lower tower layout analyzed in this paper can effectively solve the problems of insufficient four-axis load and unstable aerodynamic and vibration performance of the existing eight-axis aircraft. This paper takes the miniature octorotor as the research object and studies the aerodynamic characteristics of the miniature octorotor at different low Reynolds numbers, different air pressures and thicknesses, and the lift coefficient and lift-to-drag ratio, as well as the vibration under different elastic moduli and air pressure characteristics. The research algorithm adopted in this paper is the numerical method of fluid-solid cohesion and the control equation of flow field analysis. The research results show that, with the increase in the Reynolds number within a certain range, the aerodynamic characteristics of the miniature octorotor gradually become better. When the elastic modulus is 2.5 E, the aircraft’s specific performance is that the lift increases, the critical angle of attack increases, the drag decreases, the lift-to-drag ratio increases significantly, and the angle of attack decreases. However, the transition position of the flow around the airfoil surface is getting closer to the leading edge, and its state is more likely to transition from laminar flow to turbulent flow. When the unidirectional carbon fiber-reinforced thickness is 0.2 mm and the thin arc-shaped airfoil with the convex structure has a uniform thickness of 2.5% and a uniform curvature of 4.5%, the aerodynamic and vibration characteristics of the octorotor aircraft are most beneficial to flight.

scholarly journals PECULIARITIES OF CORRECTING THE FIGURE AMONG WOMEN OF THE FIRST MATURE AGE PERIOD BY MEANS OF SHAPING TECHNIQUES IN ACCORDANCE WITH BODY TYPES

2021 ◽  
Vol 5 (1) ◽  
pp. 30-42
Author(s):  
Olga Kozhanova ◽  
Sergii Pitenko ◽  
Natalia Gavrilova ◽  
Evgeniya Tsуkozа ◽  
Hanna Hudym ◽  
...  
Keyword(s):  
Physical Condition ◽  
Body Shape ◽  
Current Practice ◽  
Control Group ◽  
Body Type ◽  
Adult Age ◽  
New Approaches ◽  
Sports Club ◽  
Experimental Group ◽  
Selection Of

Introduction. Currently, due to environmental and social problems, nervous strain, muscle inactivity, more and more people are starting to engage in health fitness in the hope of improving health, improving physical condition, learning how to deal with stress and lose weight. Nowadays, compared to other types of fitness, shaping classes have become more and more popular as an effective way to lose weight and body shape. Although shaping was originally developed as a system of individual classes, the current practice of group classes requires the search for new approaches in planning shaping programs: there is no research on the selection of exercises, volume and intensity of classes based on individual physiques of those involved. Aim: to increase the effectiveness of classes in order to correct the figure of women 21-35 years old through the use of shaping programs, taking into account their body types. Material and methods. The study involved 30 women aged 21 - 35 years, divided into control and experimental groups, in which 15 people each were divided by somatotype. The pedagogical experiment was conducted on the basis of the sports club "Fitness Box" in Kyiv. Results. It was found that as a result of the application of the developed shaping program in the women of the experimental group there was a decrease in the fat layer in endomorphs by 13.2%, and in the control group of endomorphs by 7.2% (p < 0,05). Changes in the fat layer in the control and experimental groups are supplemented by changes in girth: chest, shoulder, abdomen, thighs, buttocks, the dynamics of which proves the effectiveness of our program compared to traditional. Conclusions. The application of the developed shaping program allows to solve the problem of improving the efficiency of shaping in order to correct the figure taking into account endomorphic body type of women first adult age.

Augmentation of Lift-to-Drag Ratio for a Wing Using Thermal Forcing

2022 ◽  
Author(s):  
Mehul Varshney ◽  
Anchal Varshney ◽  
Faisal M. Baig
Keyword(s):  
Thermal Forcing ◽  
Drag Ratio ◽  
Lift To Drag Ratio
Sign in / Sign up

Export Citation Format

Share Document