scholarly journals Modelling and simulation of working processes in Wankel engine with direct hydrogen injection system

2015 ◽  
Vol 161 (2) ◽  
pp. 42-52
Author(s):  
Władysław MITIANIEC
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Injection System ◽  
Compression Process ◽  
Injection Process ◽  
High Pollution ◽  
Spatial System ◽  
Scavenge Process ◽  
Wankel Engine ◽  
Inertia Forces

Wankel engines were very attractive in automotive sector almost forty years ago because of small dimensions, compactness, simple design, smoothness of engine work and lack of vibration caused by inertia forces. The disadvantage of such engine was very high pollution, especially of hydrocarbons and carbon monoxide and high fuel consumption. These disadvantages can be eliminated by applying of direct injection of hydrogen and in the aviation sector by applying of fuel with high octane number also at a direct injection system. The main objective of the work is modelling of the thermodynamic process taking place during the scavenge process in such engine. At assumed geometry of the engine, initial and boundary conditions the change of engine parameters such as pressure, temperature, density, heat exchange and volume are calculated on the base of zero-dimensional model as a function of rotation angle of the piston. Forming of the mixture during fuel injection process in compression process gives information about the air excess ratio. The presented model is applicable for different sort of fuels. This work is introduction to a broader analysis of the processes in spatial system. Application of hydrogen reduces of toxic components emission from such engine, but decreases also engine power.

Three-Dimensional Simulation of Gaseous Fuel Injection Through a Hybrid Approach

2010 ◽  
Vol 132 (7) ◽  
Author(s):  
L. Andreassi ◽  
A. L. Facci ◽  
S. Ubertini
Keyword(s):  
Fuel Injection ◽  
Combustion Engine ◽  
Direct Injection ◽  
Hybrid Approach ◽  
Three Dimensional ◽  
Air Entrainment ◽  
Gaseous Fuel ◽  
Injection System ◽  
Injection Process ◽  
Dimensional Simulation

Direct injection of gaseous fuel has emerged to be a high potential strategy to tackle both environmental and fuel economy requirements. However, since the electronic gaseous injection technology is rather new for automotive applications, limited experience exists on the optimum configuration of the injection system and the combustion chamber. To facilitate the development of these applications computer models are being developed to simulate gaseous injection, air entrainment, and the ensuing combustion. This paper introduces a new method for modeling the injection process of gaseous fuels in multidimensional simulations. The proposed model allows holding down grid requirements, thus, making it compatible with the three-dimensional simulation of an internal combustion engine.

A Phenomenological Model for Combustion and Emissions in Small Bore, High Speed, Direct Injection Diesel Engines

2005 ◽  
Author(s):  
N. A. Henein ◽  
I. P. Singh ◽  
L. Zhong ◽  
Y. Poonawala ◽  
J. Singh ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Diesel Engines ◽  
Phenomenological Model ◽  
High Speed ◽  
Gas Flow ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection System ◽  
Injection Process ◽  
Wide Range

This paper introduces a phenomenological model for the fuel distribution, combustion, and emissions formation in the small bore, high speed direct injection diesel engine. A differentiation is made between the conditions in large bore and small bore diesel engines, particularly regarding the fuel impingement on the walls and the swirl and squish gas flow components. The model considers the fuel injected prior to the development of the flame, fuel injected in the flame, fuel deposited on the walls and the last part of the fuel delivered at the end of the injection process. The model is based on experimental results obtained in a single-cylinder, 4-valve, direct-injection, four-stroke-cycle, water-cooled, diesel engine equipped with a common rail fuel injection system. The engine is supercharged with heated shop air, and the exhaust back pressure is adjusted to simulate actual turbo-charged diesel engine conditions. The experiments covered a wide range of injection pressures, EGR rates, injection timings and swirl ratios. Correlations and 2-D maps are developed to show the effect of combinations of the above parameters on engine out emissions. Emphasis is made on the nitric oxide and soot measured in Bosch Smoke Units (BSU).

Microscopic Spray Characteristics of Biodiesels Derived From Karanja, Jatropha, and Waste Cooking Oils

2020 ◽  
Vol 142 (12) ◽  
Author(s):  
Chetankumar Patel ◽  
Joonsik Hwang ◽  
Choongsik Bae ◽  
Rashmi A. Agarwal ◽  
Avinash Kumar Agarwal
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Injection Pressure ◽  
Axial Direction ◽  
Waste Cooking Oil ◽  
Injection System ◽  
Ambient Atmosphere ◽  
Ambient Conditions ◽  
Spray Characteristics ◽  
Spray Droplets

Abstract This study aims to assess the microscopic characteristics of Jatropha, Karanja, and Waste cooking oil-based biodiesels vis-a-vis conventional diesel under different ambient conditions in order to understand the in-cylinder processes, while using biodiesels produced from different feedstocks in the compression ignition engines. All test-fuels were injected in ambient atmosphere using a common-rail direct injection (CRDI) fuel injection system at a fuel injection pressure (FIP) of 40 MPa. Microscopic spray characteristics were measured using phase Doppler interferometer (PDI) in the axial direction of the spray at a distance of 60–90 mm downstream of the nozzle and at 0 to 3-mm distance from the central axis in the radial direction. All biodiesels exhibited relatively larger Sauter mean diameter (SMD) of the spray droplets and higher droplet velocities compared to baseline mineral diesel, possibly due to relatively higher fuel viscosity and surface tension of biodiesels. It was also observed that SMD of the spray droplets decreased with increasing distance in the radial and axial directions and the same trend was observed for all test-fuels.

A High-Speed Direct Injection Diesel Engine for Passenger Cars

1988 ◽  
Vol 202 (3) ◽  
pp. 171-181 ◽  
Author(s):  
J A Stephenson ◽  
B A Hood
Keyword(s):  
Diesel Engine ◽  
High Speed ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection System ◽  
Passenger Cars ◽  
Medium Speed ◽  
Medium Speed Engine ◽  
Hsdi Diesel Engine ◽  
Wide Speed Range

The paper describes the development of a high-speed direct injection (HSDI) diesel engine suitable for passenger car applications. The evolution from a low emissions medium-speed engine, through a four-cylinder 2.3 litre research engine, into a four-cylinder 2.0 litre production engine is presented. The challenge to the engineer has been to develop the HSDI engine to operate with acceptable noise, emissions, smoke and driveability over the wide speed range (up to 5000 r/min) required for passenger cars. The key element in this task was the optimization of the combustion system and fuel injection equipment. The HSDI is shown to have a significant fuel economy advantage over the prechamber indirect injection (IDI) engine. Future developments of the fuel injection system are described which will further enhance the HSDI engine and provide additional noise and emissions control.

Two-Stroke Engine with Fuel Semi-Direct Injection Using FAI System

2011 ◽  
Vol 130-134 ◽  
pp. 796-799
Author(s):  
Ming Ming Wu ◽  
Yan Xiang Yang ◽  
Da Guang Xi ◽  
Ping Zhang ◽  
Zhong Guo Jin
Keyword(s):  
Gasoline Engine ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection System ◽  
Injection Timing ◽  
Fuel System ◽  
Power Performance ◽  
Fuel Injection Timing ◽  
Injection Quantity ◽  
Stroke Engine

This paper presents the feasibility of semi-direct injection on a 50cm3, two-stroke motorcycle gasoline engine, which is applied FAI semi-direct injection fuel system. The structure and fuel injection system is improved based on the original carburetor engine and the FAI injector is easily installed. The results of laboratory and drive test show that, compared with the original carburetor fuel system, through optimization calibration of fuel injection timing and injection quantity can improve power performance and fuel economy.

Factors Affecting Performance of Dual Fuel Compression Ignition Engines

2013 ◽  
Vol 388 ◽  
pp. 217-222
Author(s):  
Mohamed Mustafa Ali ◽  
Sabir Mohamed Salih
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection System ◽  
Dual Fuel ◽  
Injection Timing ◽  
Compression Ignition ◽  
Factors Affecting

Compression Ignition Diesel Engine use Diesel as conventional fuel. This has proven to be the most economical source of prime mover in medium and heavy duty loads for both stationary and mobile applications. Performance enhancements have been implemented to optimize fuel consumption and increase thermal efficiency as well as lowering exhaust emissions on these engines. Recently dual fueling of Diesel engines has been found one of the means to achieve these goals. Different types of fuels are tried to displace some of the diesel fuel consumption. This study is made to identify the most favorable conditions for dual fuel mode of operation using Diesel as main fuel and Gasoline as a combustion improver. A single cylinder naturally aspirated air cooled 0.4 liter direct injection diesel engine is used. Diesel is injected by the normal fuel injection system, while Gasoline is carbureted with air using a simple single jet carburetor mounted at the air intake. The engine has been operated at constant speed of 3000 rpm and the load was varied. Different Gasoline to air mixture strengths investigated, and diesel injection timing is also varied. The optimum setting of the engine has been defined which increased the thermal efficiency, reduced the NOx % and HC%.

scholarly journals Embedded Control System for Recent Petrol Engine Control

2019 ◽  
Vol 9 (2S4) ◽  
pp. 508-511
Keyword(s):  
Coming Out ◽  
Fuel Injection ◽  
Electronic Control Unit ◽  
Direct Injection ◽  
Control Unit ◽  
Petrol Engine ◽  
Injection System ◽  
Injection Timing ◽  
Exhaust Pipe ◽  
Electronic Control

In the current scenario of automotive industries, it is much challenging for the research and developers to develop updated engines/vehicles to satisfy the proposed demands of environmental policy levels. To achieve the expected demands of emissions coming out from an engine exhaust not only with the help of converters in the exhaust pipe line but also the emissions should be controlled during burning of fuel with air in the ignition chamber itself. The controlled combustion of fuel and air requires not only the control fuel injection timing with duration of injection and tune up of the complete fuel injection system with hardware components of ECU but also requires the control of ignition timing. The complete electronic control for petrol engine with direct injection unit is required to communicate between PC and an engine. CAN with SPI interface is used to communicate the electronic control unit with engine

Predicting Hydrocarbon Emissions From Direct Injection Diesel Engines

2002 ◽  
Vol 124 (3) ◽  
pp. 708-716 ◽  
Author(s):  
P. A. Lakshminarayanan ◽  
N. Nayak ◽  
S. V. Dingare ◽  
A. D. Dani
Keyword(s):  
Diesel Engines ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection System ◽  
Hydrocarbon Emissions ◽  
Operating Parameters ◽  
Fuel Injection System ◽  
Lean Combustion ◽  
Medium Speed ◽  
Hc Emissions

Hydrocarbon (HC) emissions from direct injection (DI) diesel engines are mainly due to fuel injected and mixed beyond the lean combustion limit during ignition delay and fuel effusing from the nozzle sac at low pressure. In the present paper, the concept has been developed to provide an elegant model to predict the HC emissions considering slow burning. Eight medium speed engines differing widely in bores, strokes, rated speeds, and power were studied for applying the model. The engines were naturally aspirated, turbocharged, or turbocharged with intercooling. The model has been validated by collecting data on HC emission, and pressures in the cylinder and in the fuel injection system from the experimental engines. New coefficients for the correlation of HC with operating parameters were obtained and these are different from the values published earlier, based on single-engine experiments.

Sign in / Sign up

Export Citation Format

Share Document