A Phenomenological Model for Combustion and Emissions in Small Bore, High Speed, Direct Injection Diesel Engines

2005 ◽  
Author(s):  
N. A. Henein ◽  
I. P. Singh ◽  
L. Zhong ◽  
Y. Poonawala ◽  
J. Singh ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Diesel Engines ◽  
Phenomenological Model ◽  
High Speed ◽  
Gas Flow ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection System ◽  
Injection Process ◽  
Wide Range

This paper introduces a phenomenological model for the fuel distribution, combustion, and emissions formation in the small bore, high speed direct injection diesel engine. A differentiation is made between the conditions in large bore and small bore diesel engines, particularly regarding the fuel impingement on the walls and the swirl and squish gas flow components. The model considers the fuel injected prior to the development of the flame, fuel injected in the flame, fuel deposited on the walls and the last part of the fuel delivered at the end of the injection process. The model is based on experimental results obtained in a single-cylinder, 4-valve, direct-injection, four-stroke-cycle, water-cooled, diesel engine equipped with a common rail fuel injection system. The engine is supercharged with heated shop air, and the exhaust back pressure is adjusted to simulate actual turbo-charged diesel engine conditions. The experiments covered a wide range of injection pressures, EGR rates, injection timings and swirl ratios. Correlations and 2-D maps are developed to show the effect of combinations of the above parameters on engine out emissions. Emphasis is made on the nitric oxide and soot measured in Bosch Smoke Units (BSU).

A High-Speed Direct Injection Diesel Engine for Passenger Cars

1988 ◽  
Vol 202 (3) ◽  
pp. 171-181 ◽  
Author(s):  
J A Stephenson ◽  
B A Hood
Keyword(s):  
Diesel Engine ◽  
High Speed ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection System ◽  
Passenger Cars ◽  
Medium Speed ◽  
Medium Speed Engine ◽  
Hsdi Diesel Engine ◽  
Wide Speed Range

The paper describes the development of a high-speed direct injection (HSDI) diesel engine suitable for passenger car applications. The evolution from a low emissions medium-speed engine, through a four-cylinder 2.3 litre research engine, into a four-cylinder 2.0 litre production engine is presented. The challenge to the engineer has been to develop the HSDI engine to operate with acceptable noise, emissions, smoke and driveability over the wide speed range (up to 5000 r/min) required for passenger cars. The key element in this task was the optimization of the combustion system and fuel injection equipment. The HSDI is shown to have a significant fuel economy advantage over the prechamber indirect injection (IDI) engine. Future developments of the fuel injection system are described which will further enhance the HSDI engine and provide additional noise and emissions control.

scholarly journals Characteristics of pressure wave in common rail fuel injection system of high-speed direct injection diesel engines

2016 ◽  
Vol 8 (5) ◽  
pp. 168781401664824 ◽  
Author(s):  
Mohammad Reza Herfatmanesh ◽  
Zhijun Peng ◽  
Alexis Ihracska ◽  
Yuzhen Lin ◽  
Lipeng Lu ◽  
...  
Keyword(s):  
Diesel Engines ◽  
Pressure Wave ◽  
High Speed ◽  
Fuel Injection ◽  
Direct Injection ◽  
Common Rail ◽  
Injection System ◽  
Fuel Injection System

Characteristics of injection of diesel fuel, rapeseed oil and their mixtures in diesel engines of various types

2021 ◽  
pp. 167-178
Author(s):  
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Diesel Engines ◽  
Rapeseed Oil ◽  
High Speed ◽  
Fuel Injection ◽  
Experimental Studies ◽  
Fuel Injector ◽  
High Speed Diesel ◽  
Engine Type

The necessity of adapting diesel engines to work on vegetable oils is justified. The possibility of using rapeseed oil and its mixtures with petroleum diesel fuel as motor fuels is considered. Experimental studies of fuel injection of small high-speed diesel engine type MD-6 (1 Ch 8,0/7,5)when using diesel oil and rapeseed oil and computational studies of auto-tractor diesel engine type D-245.12 (1 ChN 11/12,5), working on blends of petroleum diesel fuel and rapeseed oil. When switching autotractor diesel engine from diesel fuel to rapeseed oil in the full-fuel mode, the mass cycle fuel supply increased by 12 %, and in the small-size high-speed diesel engine – by about 27 %. From the point of view of the flow of the working process of these diesel engines, changes in other parameters of the fuel injection process are less significant. Keywords diesel engine; petroleum diesel fuel; vegetable oil; rapeseed oil; high pressure fuel pump; fuel injector; sprayer

scholarly journals Performance evaluation of common rail direct injection (CRDI) engine fuelled with Uppage Oil Methyl Ester (UOME)

2015 ◽  
Vol 4 (1) ◽  
pp. 1-10 ◽  
Author(s):  
D.N. Basavarajappa ◽  
N. R. Banapurmath ◽  
S.V. Khandal ◽  
G. Manavendra
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Diesel Engines ◽  
High Speed ◽  
Alternative Fuels ◽  
High Pressures ◽  
Fuel Injection ◽  
Injection Timing ◽  
Engine Operation ◽  
Performance And Emission

For economic and social development of any country energy is one of the most essential requirements. Continuously increasing price of crude petroleum fuels in the present days coupled with alarming emissions and stringent emission regulations has led to growing attention towards use of alternative fuels like vegetable oils, alcoholic and gaseous fuels for diesel engine applications. Use of such fuels can ease the burden on the economy by curtailing the fuel imports. Diesel engines are highly efficient and the main problems associated with them is their high smoke and NOx emissions.  Hence there is an urgent need to promote the use of alternative fuels in place of high speed diesel (HSD) as substitute. India has a large agriculture base that can be used as a feed stock to obtain newer fuel which is renewable and sustainable. Accordingly Uppage oil methyl ester (UOME) biodiesel was selected as an alternative fuel. Use of biodiesels in diesel engines fitted with mechanical fuel injection systems has limitation on the injector opening pressure (300 bar). CRDI system can overcome this drawback by injecting fuel at very high pressures (1500-2500 bar) and is most suitable for biodiesel fuels which are high viscous. This paper presents the performance and emission characteristics of a CRDI diesel engine fuelled with UOME biodiesel at different injection timings and injection pressures. From the experimental evidence it was revealed that UOME biodiesel yielded overall better performance with reduced emissions at retarded injection timing of -10° BTDC in CRDI mode of engine operation.

Multi-Valve High-Speed Direct Injection Diesel Engines—the Design Challenge

1993 ◽  
Vol 207 (4) ◽  
pp. 307-315
Author(s):  
I P Gilbert ◽  
A R Heath ◽  
I D Johnstone
Keyword(s):  
Diesel Engine ◽  
Fuel Economy ◽  
Cylinder Head ◽  
High Speed ◽  
Fuel Injection ◽  
Direct Injection ◽  
Selection Strategy ◽  
Design Challenge ◽  
Hsdi Diesel Engine ◽  
High Level

The need to increase power, to improve fuel economy and to meet stringent exhaust emissions legislation with a high level of refinement has provided a challenge for the design of a compact high-speed direct injection (HSDI) diesel engine. This paper describes various aspects of cylinder head design with particular consideration of layout and number of valves, valve actuation, port selection strategy, fuel injection systems and cylinder head construction.

Effect of Swirl Ratio and Injection Pressure on Autoignition, Combustion and Emissions in a High Speed Direct Injection Diesel Engine Fuelled With Biodiesel (B-20)

2009 ◽  
Author(s):  
Vinay Nagaraju ◽  
Mufaddel Dahodwala ◽  
Kaushik Acharya ◽  
Walter Bryzik ◽  
Naeim A. Henein
Keyword(s):  
Diesel Engine ◽  
High Speed ◽  
Direct Injection ◽  
Injection Pressure ◽  
Combustible Mixture ◽  
Injection System ◽  
Ignition Process ◽  
Swirl Ratio ◽  
Mixture Formation ◽  
Physical And Chemical

Biodiesel has different physical and chemical properties than ultra low sulfur diesel fuel (ULSD). The low volatility of biodiesel is expected to affect the physical processes, mainly fuel evaporation and combustible mixture formation. The higher cetane number of biodiesel is expected to affect the rates of the chemical reactions. The combination of these two fuel properties has an impact on the auto ignition process, subsequently combustion and engine out emissions. Applying different swirl ratios and injection pressures affect both the physical and chemical processes. The focus of this paper is to investigate the effect of varying the swirl ratio and injection pressure in a single-cylinder research diesel engine using a blend of biodiesel and ULSD fuel. The engine is a High Speed Direct Injection (HSDI) equipped with a common rail injection system, EGR system and a swirl control mechanism. The engine is operated under simulated turbocharged conditions with 3 bar Indicated Mean Effective Pressure (IMEP) at 1500 rpm, using 100% ULSD and a blend of 20% biodiesel and 80% ULSD fuel. The biodiesel is developed from soy bean oil. A detailed analysis of the apparent rate of heat release (ARHR) is made to determine the role of the biodiesel component of B-20 in the combustible mixture formation, autoignition process, premixed, mixing controlled and diffusion controlled combustion fractions. The results explain the factors that cause an increase or a drop in NOx emissions reported in the literature when using biodiesel.

Scaling liquid penetration in evaporating sprays for different size diesel engines

2019 ◽  
Vol 21 (9) ◽  
pp. 1662-1677 ◽  
Author(s):  
Xinyi Zhou ◽  
Tie Li ◽  
Yijie Wei ◽  
Ning Wang
Keyword(s):  
Diesel Engine ◽  
Diesel Engines ◽  
High Speed ◽  
Scaling Laws ◽  
Fuel Injection ◽  
Pollutant Emissions ◽  
Liquid Penetration ◽  
Spray Characteristics ◽  
Penetration Length ◽  
Air Mixing

Scaled model experiments can greatly reduce the cost, time and energy consumption in diesel engine development, and the similarity of spray characteristics has a primary effect on the overall scaling results of engine performance and pollutant emissions. However, although so far the similarity of spray characteristics under the non-evaporating condition has been studied to some extent, researches on scaling the evaporating sprays are still absent. The maximum liquid penetration length has a close relationship with the spray evaporation processes and is a key parameter in the design of diesel engine spray combustion system. In this article, the similarity of maximum liquid penetration length is theoretically derived based on the hypotheses that the spray evaporation processes in modern high-pressure common rail diesel engines are fuel–air mixing controlled and local interphase transport controlled, respectively. After verifying that the fuel injection rates are perfectly scaled, the similarity of maximum liquid penetration length in evaporating sprays is studied for three scaling laws using two nozzles with hole diameter of 0.11 and 0.14 mm through the high-speed diffused back-illumination method. Under the test conditions of different fuel injection pressures, ambient temperatures and densities, the lift-off law and speed law lead to a slightly increased maximum liquid penetration length, while the pressure law can well scale the maximum liquid penetration length. The experimental results are consistent with the theoretical analyses based on the hypothesis that the spray evaporation processes are fuel–air mixing controlled, indicating that the local interphase transports of energy, momentum and mass on droplet surface are not rate-controlled steps with respect to spray evaporation processes.

Ion Current, Combustion and Emission Characteristics in an Automotive Common Rail Diesel Engine

2012 ◽  
Vol 134 (4) ◽  
Author(s):  
Naeim A. Henein ◽  
Tamer Badawy ◽  
Nilesh Rai ◽  
Walter Bryzik
Keyword(s):  
Diesel Engine ◽  
Diesel Engines ◽  
Direct Injection ◽  
Common Rail ◽  
Ion Current ◽  
Injection System ◽  
Feedback Signal ◽  
Common Rail Injection System ◽  
Common Rail Injection ◽  
No Emissions

Advanced electronically controlled diesel engines require a feedback signal to the ECU to adjust different operating parameters and meet demands for power, better fuel economy and low emissions. Different types of in-cylinder combustion sensors are being considered to produce this signal. This paper presents results of an experimental investigation on the characteristics of the ion current in an automotive diesel engine equipped with a common rail injection system. The engine is a 1.9 L, 4-cylinder, direct injection diesel engine. Experiments covered different engine loads and injection pressures. The relationships between the ion current, combustion parameters and engine out NO emissions and opacity are presented. The analysis of the experimental data identified possible sources of the ion current produced in diesel engines.

Detecting and Correcting Cylinder Imbalance in Direct Injection Engines

2000 ◽  
Vol 123 (3) ◽  
pp. 413-424 ◽  
Author(s):  
M. J. van Nieuwstadt ◽  
I. V. Kolmanovsky
Keyword(s):  
High Pressure ◽  
Diesel Engine ◽  
High Speed ◽  
Fuel Injection ◽  
Direct Injection ◽  
Direct Injection Engines ◽  
High Speed Diesel ◽  
On Line ◽  
Manufacturing Accuracy ◽  
Adaptation Scheme

Modern direct injection engines feature high pressure fuel injection systems that are required to control the fuel quantity very accurately. Due to limited manufacturing accuracy these systems can benefit from an on-line adaptation scheme that compensates for injector variability. Since cylinder imbalance affects many measurable signals, different sensors and algorithms can be used to equalize torque production by the cylinders. This paper compares several adaptation schemes that use different sensors. The algorithms are evaluated on a cylinder-by-cylinder simulation model of a direct injection high speed diesel engine. A proof of stability and experimental results are reported as well.

Modelling of Spray–Swirl Interaction in Direct Injection Diesel Engine Combustion Chambers

1985 ◽  
Vol 199 (3) ◽  
pp. 187-198 ◽  
Author(s):  
P S Mehta ◽  
A K Gupta
Keyword(s):  
Diesel Engine ◽  
Fuel Injection ◽  
Direct Injection ◽  
Three Dimensional ◽  
Combustion Chambers ◽  
Direct Injection Diesel Engine ◽  
Wide Range ◽  
Engine Combustion ◽  
Computation Scheme ◽  
Good Agreement

A mathematical model for predicting spray–swirl interaction in a direct injection diesel engine combustion chamber is developed using centre-line velocity vector/continuum approach. The model has three-dimensional features in fuel spray motion. The present model responds to the various air swirl, fuel injection and cylinder charge conditions. The predicted results are compared with the analytical and experimental data available from various sources in the two-dimensional case. Very good agreement is achieved over a wide range of data. The three-dimensional predictions are directly possible without any alteration in the computation scheme.

Sign in / Sign up

Export Citation Format

Share Document