scholarly journals Enhancing Ossiointegration And Corrosion Properties of Ti6Al4V Alloy By Coating With Chitosan – Collagen- Hydroxyapatite For Biomedical Applications

2021 ◽  
Author(s):  
Adnan M.Mahdi ◽  
Abbas F. Essa ◽  
Mohammed Kh. Khalf
Keyword(s):  
Simulated Body Fluid ◽  
Corrosion Test ◽  
Body Fluid ◽  
Biomedical Applications ◽  
Maximum Growth ◽  
Muffle Furnace ◽  
Corrosion Properties ◽  
Air Atmosphere ◽  
Heat Treated ◽  
Sbf Solution

Abstract In this research, Ti-6Al-4V alloy samples were coated with 4 gm strontium hydroxyapatite with 2 gm from chitosan and (2,4,6) gm from collagen and the samples heat treated at 150 ºC in muffle furnace for one hour under air atmosphere. The sample were tested by XRD,FTIR,SEM and corrosion test was also achieved. The samples were immersed in a laboratory prepared simulated body fluid (SBF) solution for two weeks, the samples treated at 150 ºC in muffle furnace for one hour under air atmosphere to get more bonding for new layer . The samples tested by XRD,FTIR,SEM and corrosion test was also achieved after immersing . The sample coated with 6 gm collagen showed maximum growth of hydroxyapatite formed from simulated body fluid SBF and corrosion characteristics was much improved.

In Vitro Bioactivity Assessment of Metallic Magnesium

2006 ◽  
Vol 309-311 ◽  
pp. 453-456 ◽  
Author(s):  
Haydée Y. López ◽  
Dora A. Cortés-Hernández ◽  
Sergio Escobedo ◽  
D. Mantovani
Keyword(s):  
Simulated Body Fluid ◽  
Body Fluid ◽  
Biomedical Applications ◽  
Degradation Rate ◽  
Magnesium Concentration ◽  
In Vitro Bioactivity ◽  
Ph Values ◽  
Heat Treated ◽  
Bonelike Apatite

In the aim to decrease the degradation rate of magnesium in simulated body fluid, pure magnesium was treated by two different routes, i) by soaking specimens in an HF aqueous solution at 30oC for 30 min and ii) by heating specimens at 345oC for 15 min. The treated samples were immersed in simulated body fluid (SBF) at 37oC for different periods of time. Samples with no treatment were also immersed in SBF. The magnesium released into the SBF, the weight loss of the specimens and the pH of SBF increased with time of immersion in all the cases. The heat treated samples showed a lower degradation rate and lower pH values. A substantial decrease of magnesium concentration in the SBF corresponding to the heat treated samples was also observed. However, the degradation rate of the heat treated samples remains being extremely high. On the other hand, a bonelike apatite layer was observed after only 3 days of immersion in SBF in all the cases. The thickness of this layer increased with time of immersion. Further research needs to be performed to decrease the degradation rate. However, these results indicate that magnesium is a highly potential bioactive material for biomedical applications.

Investigation of corrosion behavior of polypyrrole-coated Ti using dynamic electrochemical impedance spectroscopy (DEIS)

RSC Advances ◽  
2016 ◽  
Vol 6 (83) ◽  
pp. 80275-80285 ◽  
Author(s):  
Bhavana Rikhari ◽  
S. Pugal Mani ◽  
N. Rajendran
Keyword(s):  
Electrochemical Impedance Spectroscopy ◽  
Impedance Spectroscopy ◽  
Simulated Body Fluid ◽  
Corrosion Behavior ◽  
Body Fluid ◽  
Electrochemical Impedance ◽  
Sbf Solution ◽  
Dynamic Electrochemical Impedance Spectroscopy

In the present work, dynamic electrochemical impedance spectroscopy (DEIS) was used to investigate the corrosion behavior of polypyrrole (PPy)-coated titanium (Ti) in simulated body fluid (SBF) solution.

scholarly journals Corrosion study of metallic biomaterials in simulated body fluid

10.30544/384 ◽  
2011 ◽  
Vol 17 (1) ◽  
pp. 13-22 ◽  
Author(s):  
Hamid Reza Asgari Bidhendi ◽  
Majid Pouranvari
Keyword(s):  
Stainless Steel ◽  
Simulated Body Fluid ◽  
Corrosion Behavior ◽  
Body Fluid ◽  
Pure Titanium ◽  
Localized Corrosion ◽  
Commercially Pure Titanium ◽  
Corrosion Properties ◽  
Cyclic Polarization ◽  
Cp Ti

Titanium alloys and stainless steel 316L are still the most widely used biomaterials for implants despite emerging new materials for this application. There is still someambiguity in corrosion behavior of metals in simulated body fluid (SBF). This paper aims at investigating the corrosion behavior of commercially pure titanium (CP-Ti), Ti–6Al–4V and 316LVM stainless steel (316LVM) in SBF (Hank’s solution) at37 ºC using the cyclic polarization test. Corrosion behavior was described in terms of breakdown potential, the potential and rate ofcorrosion, localized corrosion resistance, andbreakdown repassivation. The effects of anodizing on CP-Ti samples and the passivation on the 316LVM were studied in detail. It was shown that CP-Ti exhibited superior corrosion properties compared to Ti–6Al–4V and 316LVM.

scholarly journals Bioactivity Behavior Evaluation of PCL-Chitosan-Nanobaghdadite Coating on AZ91 Magnesium Alloy in Simulated Body Fluid

Coatings ◽  
2020 ◽  
Vol 10 (3) ◽  
pp. 231
Author(s):  
Farzad Soleymani ◽  
Rahmatollah Emadi ◽  
Sorour Sadeghzade ◽  
Fariborz Tavangarian
Keyword(s):  
Simulated Body Fluid ◽  
Corrosion Rate ◽  
Composite Coating ◽  
Body Fluid ◽  
Composite Coatings ◽  
Phosphate Buffer Solution ◽  
Az91 Alloy ◽  
Apatite Formation ◽  
Az91 Magnesium Alloy ◽  
Sbf Solution

Polymer–ceramic composite coatings on magnesium-based alloys have attracted lots of attention in recent years, to control the speed of degradability and to enhance bioactivity and biocompatibility. In this study, to decrease the corrosion rate in a simulated body fluid (SBF) solution for long periods, to control degradability, and to enhance bioactivity, polycaprolactone–chitosan composite coatings with different percentages of baghdadite (0 wt.%, 3 wt.%, and 5 wt.%) were applied to an anodized AZ91 alloy. According to the results of the immersion test of the composite coating containing 3 wt.% baghdadite in a phosphate buffer solution (PBS), the corrosion rate decreased from 0.45 (for the AZ91 sample) to 0.11 mg/cm2·h after seven days of immersion. To evaluate the apatite formation capability of specimens, samples were immersed in an SBF solution. The results showed that the samples were bioactive as apatite layers formed on the surface of specimens. The composite coating containing 3 wt.% baghdadite showed the highest apatite-formation capability, with a controlled release of ions, and the lowest corrosion rate in the SBF.

scholarly journals Biomimetic Coating of Modified Titanium Surfaces with Hydroxyapatite Using Simulated Body Fluid

2015 ◽  
Vol 2015 ◽  
pp. 1-8 ◽  
Author(s):  
Mohsin Nazir ◽  
Ong Pei Ting ◽  
Tan See Yee ◽  
Saravanan Pushparajan ◽  
Dasan Swaminathan ◽  
...  
Keyword(s):  
Simulated Body Fluid ◽  
Tricalcium Phosphate ◽  
Body Fluid ◽  
Energy Dispersive Spectrometer ◽  
Pure Titanium ◽  
Commercially Pure Titanium ◽  
Phosphate Coatings ◽  
Infrared Spectrometer ◽  
Sbf Solution ◽  
The Fourier Transform

This study investigated the viability of coating commercially pure titanium (CPTi) surfaces, modified via sandblasting and acid etching, with hydroxyapatite (HA)/tricalcium phosphate coatings using a simulated body fluid (SBF) solution. The samples were immersed in SBF from 3 to 7 days. The morphology and the chemistry of the HA/tricalcium phosphate coating were then analysed. Prior to immersion in SBF, the samples were sandblasted and acid etched to mimic the morphology and roughness of commercially available dental implants. The SBF aided in the formation of crystalline HA/tricalcium phosphate coatings on all the samples. The coatings were uniform and had roughness values higher than the underlying substrate. The highest roughness values for the coatings on the surfaces were obtained at 7 days of immersion in SBF with averageSavalues of 2.9 ± 0.2 µm. The presence of HA/tricalcium phosphate on the surfaces was confirmed by the Scanning Electron Microscope (SEM), Energy Dispersive Spectrometer (EDS), the X-Ray Diffraction (XRD), and the Fourier Transform Infrared Spectrometer (FTIR) analysis. This study shows that it is possible to obtain an adequate and uniform hydroxyapatite coating on pure titanium substrates in a shorter period of time with characteristics that favour the ultimate goal of implants therapy, that is, osseointegration.

scholarly journals Effect of Zn Content on Orthopedic Mg aAlloy as Smart Implant

2020 ◽  
Vol 71 (6) ◽  
pp. 96-110
Author(s):  
Omyma Ramadan Mohammed Khalifa ◽  
Abdel-Wahab Abd Elhamid Ali ◽  
Aisha Kassab ◽  
Amal Hemida Tilp ◽  
Marwa Mohamed Mohamed Mohamed Esmail
Keyword(s):  
Corrosion Resistance ◽  
Simulated Body Fluid ◽  
Body Fluid ◽  
Biomedical Applications ◽  
Orthopedic Implants ◽  
X Ray Diffraction ◽  
Electro Deposition ◽  
X Ray ◽  
Zn Content ◽  
The Media

In recent years, smart implants take the most attention in the field of bone manufacturing. Our study seeks to develop the biodegradability of Mg alloys to use orthopedic implants for the biomedical applications to avoid post removal of the implant. Mg and Zn are very important to human body and have no toxicity. Mg - 6% wt Zn biodegradability is studied in simulated body fluid for two and four weeks. Four electro-deposition bathes are used to deposit a coat on the substrate to improve the corrosion resistance of this alloy in the media of simulated body fluid. The following analyses were studied to emphasize the research aim. Scanning electron microscope (SEM), Energy dispersive X-Ray (EDX) analysis shows the surface morphology and the elements of the coat phases components. The results also confirmed by X-Ray diffraction Pattern (XRD) that show the phases that confirmed the formation of hydroxyapatite HA phase, Fourier-Transform Infrared Spectroscopy (FTIR) to investigate the functional groups of the phases coats that confirm the formation of hydroxyapatite and the electrochemical measurements that investigate the improvement of corrosion resistance. The results indicated that the fourth bath gives the best coat and four weeks immersion gives more corrosion resistance than two weeks.

Sign in / Sign up

Export Citation Format

Share Document