Oscillatory Motion of Viscoelastic Drops on Slippery Lubricated Surfaces

2021 ◽  
Author(s):  
Paolo Sartori ◽  
Davide Ferraro ◽  
Marco Dassie ◽  
Alessio Meggiolaro ◽  
Daniele Filippi ◽  
...  
Keyword(s):  
Normal Stress Difference ◽  
Oscillatory Motion ◽  
Solid Surfaces ◽  
Stress Difference ◽  
Drop Volume ◽  
First Normal Stress Difference ◽  
Average Speed ◽  
Induced Motion ◽  
Instantaneous Speed ◽  
Viscous Solutions

Abstract The introduction of slippery lubricated surfaces allows the investigation of the flow of highly viscous solutions which otherwise will hardly move on standard solid surfaces. Here we present the study of the gravity induced motion of small viscoelastic drops deposited on inclined lubricated surfaces. The viscoelastic fluids exhibit shear thinning and, more importantly, a significant first normal stress difference N1. Despite the homogeneity of the surface and of the fluids, drops of sufficiently high N1 move down with an oscillating instantaneous speed whose frequency is found to be directly proportional to the average speed and inversely to the drop volume. The oscillatory motion is caused by the formation of a bulge at the drop rear that starts rolling around the moving drop.

Rheological Properties of Concentrated 1-Allyl-3-Methylimidazolium Chloride Cellulose Solutions

2011 ◽  
Vol 199-200 ◽  
pp. 3-6
Author(s):  
Fei Lu ◽  
Jun Song ◽  
Bo Wen Cheng ◽  
Hong Jun Zang ◽  
Yi Liang
Keyword(s):  
Power Law ◽  
Loss Modulus ◽  
Polymer Concentration ◽  
Normal Stress Difference ◽  
Stress Difference ◽  
Rheological Measurement ◽  
First Normal Stress Difference ◽  
Power Law Index ◽  
Cellulose Concentration ◽  
Newtonian Behavior

The viscosity behaviors and elastic properties of concentrated cellulose 1-allyl-3-methy -limidazolium Chloride solutions were investigated in the concentration from 10 wt% to 25 wt%. Rheological measurement showed that the solution was pesudoplastic fluid. The non-Newtonian behavior was improved and shear-thinning tendency became more pronounced with increasing polymer concentration. The power law index ranged from 0.19 to 0.30. The effects of cellulose concentration to the storage modulus G′ and the loss modulus G″ were analyzed. First normal stress difference (N1) increased with increasing concentration.

The first normal stress difference of non-Brownian hard-sphere suspensions in the oscillatory shear flow near the liquid and crystal coexistence region

Soft Matter ◽  
2020 ◽  
Vol 16 (43) ◽  
pp. 9864-9875
Author(s):  
Young Ki Lee ◽  
Kyu Hyun ◽  
Kyung Hyun Ahn
Keyword(s):  
Shear Flow ◽  
Normal Stress ◽  
Hard Sphere ◽  
Normal Stress Difference ◽  
Oscillatory Shear ◽  
Stress Difference ◽  
Large Amplitude Oscillatory Shear ◽  
First Normal Stress Difference ◽  
Oscillatory Shear Flow ◽  
Sphere Suspensions

The first normal stress difference (N1) as well as shear stress of non-Brownian hard-sphere suspensions in small to large amplitude oscillatory shear flow is investigated.

Effect of Inner Cavity’s Gas Flow Rate on the Extrusion Forming of Plastic Micro-Pipe

2020 ◽  
Vol 842 ◽  
pp. 279-284
Author(s):  
Zhong Ren ◽  
Xing Yuan Huang
Keyword(s):  
Finite Element ◽  
Normal Stress ◽  
Flow Rate ◽  
Gas Flow ◽  
Normal Stress Difference ◽  
Stress Difference ◽  
Gas Flow Rate ◽  
Flow Rates ◽  
First Normal Stress Difference ◽  
Extrusion Forming

During the manufacture of plastic micro-pipe, a certain volume of gas should be properly injected into the inner cavity to overcome the collapse and adhesion problems. In this work, the extrusion forming of plastic micro-tube under the role of inner cavity’s gas were numerically studied. At the same time, the effect of inner cavity’s gas flow rate on the extrusion deformation of plastic micro-pipe was also numerically investigated by using the finite element method. A kind of 2D two-phase fluid geometric model and finite element mesh were established and some reasonable boundary conditions and material parameters were imposed. Under a fixed volume flow rate of melt, different flow rates of inner cavity gas were imposed on the inlet of inner cavity’s gas. The extrusion deformation profile and deformation ratio of plastic micro-pipe under different flow rates of gas were all obtained. To ascertain the mechanisms of effect of inner cavity’s gas flow rate on the extrusion deformation of plastic micro-tube, the flow velocities, pressure, shear rate, normal stress, and the first normal stress difference of melt all obtained and analyzed. Numerical results show that with the increase of inner cavity’s gas flow rate, the radial velocity, axial velocity, pressure, shear rate, normal stress, and the first normal stress difference of melt all increase, which makes the extrusion deformation become more and more serious. In practice, reasonable controlling of the inner cavity’s gas flow rate is very important. In the other hand, it can adjust the size of extruded plastic micro-pipe.

Normal stresses and microstructure in bounded sheared suspensions via Stokesian Dynamics simulations

2000 ◽  
Vol 412 ◽  
pp. 279-301 ◽  
Author(s):  
ANUGRAH SINGH ◽  
PRABHU R. NOTT
Keyword(s):  
Normal Stress ◽  
Couette Flow ◽  
Normal Stress Difference ◽  
Stress Difference ◽  
Normal Stresses ◽  
Plane Couette Flow ◽  
Stokesian Dynamics ◽  
First Normal Stress Difference ◽  
Particle Pressure ◽  
Dynamics Simulations

We report the normal stresses in a non-Brownian suspension in plane Couette flow determined from Stokesian Dynamics simulations. The presence of normal stresses that are linear in the shear rate in a viscometric flow indicates a non-Newtonian character of the suspension, which is otherwise Newtonian. While in itself of interest, this phenomenon is also important because it is believed that normal stresses determine the migration of particles in flows with inhomogeneous shear fields. We simulate plane Couette flow by placing a layer of clear fluid adjacent to one wall in the master cell, which is then replicated periodically. From a combination of the traceless hydrodynamic stresslet on the suspended particles, the stresslet due to (non-hydrodynamic) inter-particle forces, and the total normal force on the walls, we determine the hydrodynamic and inter-particle force contributions to the isotropic ‘particle pressure’ and the first normal stress difference. We determine the stresses for a range of the particle concentration and the Couette gap. The particle pressure and the first normal stress difference exhibit a monotonic increase with the mean particle volume fraction ϕ. The ratio of normal to shear stresses on the walls also increases with ϕ, substantiating the result of Nott & Brady (1994) that this condition is required for stability to concentration fluctuations. We also study the microstructure by extracting the pair distribution function from our simulations; our results are in agreement with previous studies showing anisotropy in the pair distribution, which is the cause of normal stresses.

scholarly journals Vliv smykové viskozity a elasticity na senzorickou viskozitu modelových kapalných potravin

1999 ◽  
Vol 17 (No. 1) ◽  
pp. 23-30 ◽  
Author(s):  
P. Novotna ◽  
M. Houska ◽  
V. Sopr ◽  
H. Valentova ◽  
P. Stern
Keyword(s):  
Shear Flow ◽  
Normal Stress ◽  
Shear Viscosity ◽  
Normal Stress Difference ◽  
Rheological Parameters ◽  
Cellulose Derivatives ◽  
Moderate Increase ◽  
Stress Difference ◽  
First Normal Stress Difference ◽  
Normal Difference

The shear flow rheological properties of sugar solutions (70% w/w concentration) modified by different cellulose derivatives have been measured. Thickeners  were expected to cause the viscoelastic behaviour of the resulting sol ution. Therefore, the elastic rheological parameters were measured by oscillatory shear technique (phase angle, elastic modulus) and also the first normal stress difference N<sub>1</sub>. The increase of thickener concen tration caused a moderate increase of non-Newtonian behaviour in the shear flow. The sensory viscosity (ra nged between 0 and 100%) was evaluated by five different methods - as an effort for stirring with teaspoon, time for flowing down the spoon, slurping from spoon, compression between tongue and palate and swallowing. The influence of shear viscosity and first normal difference on sensory viscosity was tested. Correlation procedu re between change of sensory viscosity .tlSE and change of shear viscosity .tlJ.Iz showed that only for swallowing there is a statistically evident de­pendence. The correlation between change of sensory viscosity t.SE and first normal stress difference N<sub>1</sub> is not statistically   evident. For all the methods of sensory evaluation the dependence between these parameters is only weak and indirect (with increasing normal stress difference the sensory viscosity is decreasing).

Numerical Simulation of a First Normal Stress Difference-Based Model for Shear-Induced Crystallization of Polyethylene

2011 ◽  
Vol 266 ◽  
pp. 130-134
Author(s):  
Jin Yan Wang ◽  
Jing Bo Chen ◽  
Chang Yu Shen
Keyword(s):  
Numerical Simulation ◽  
Shear Flow ◽  
Normal Stress ◽  
Viscoelastic Model ◽  
Normal Stress Difference ◽  
Simple Shear Flow ◽  
Stress Difference ◽  
Avrami Model ◽  
First Normal Stress Difference ◽  
Induced Crystallization

The paper presents a numerical simulation for the isothermal flow-induced crystallization of polyethylene under a simple shear flow. The effect of flow on crystllization is considered through the simple mathematical relationship between the additional number of nuclei induced by shear treatment and the first normal stress difference. Leonov viscoelastic model and Avrami model are used to describe the normal stress difference and the crystallization kinetics, respectively. It is found that the short-term shear treatment has a large effect on the crystallization dynamics of polyethylene , but the effect of the intensity of the shear flow is not infinite ,which shows a saturation phenomenon, namely, the accelerated degree of crystallization tending to level off when the shear rate or shear time is large enough.

Sign in / Sign up

Export Citation Format

Share Document