scholarly journals Study On The Single Point Incremental Sheet Forming of AISI 321 Variable Wall Angle Geometry

2021 ◽  
Author(s):  
Muhammad Jawad Afzal ◽  
Asif Israr ◽  
Muhammad Soban Akram ◽  
Abdul Muqeet
Keyword(s):  
Low Cost ◽  
Single Point ◽  
Cnc Machine ◽  
Forming Process ◽  
Wall Angle ◽  
Metal Forming Process ◽  
Clamping System ◽  
Variable Wall ◽  
Aisi 321 ◽  
Wall Geometry

Abstract For rapid prototyping, design validation and small batch productions process with low tooling cost is preferred. Single Point Incremental Forming (SPIF) is a die-less sheet metal forming process which requires only low cost forming tool driven by CNC machine in a toolpath to form required geometry at room temperature from sheet blank clamped in a low cost and low stiffness clamping system. In this study, effect of process parameters such as tool radius, feed rate and lubrication are considered on the formability of the truncated profile of AISI 321 Variable Wall Geometry (VWA). Set parameters conditions with 2 level layers are optimized using numerical and statistical approach. Experimentation on the same setup is carried out by selecting the most, least and mid favorable solutions optimized on the basis of forming forces and stresses in the sheet. Geometrical accuracy, sheet thinning, and forming forces are compared analytically, numerically and experimentally addressing the inadequacy of analytically models for Variable Wall Angle Geometries.

Improvement of Wall Angle in AISI 304 Stainless Steel Cup using Five Stage Single Point Incremental Forming

2020 ◽  
Vol 12 (1) ◽  
Author(s):  
D. Suresh Kumar ◽  
N. Ethiraj
Keyword(s):  
Incremental Forming ◽  
Single Point ◽  
Research Work ◽  
Single Stage ◽  
304 Stainless Steel ◽  
Forming Process ◽  
Wall Angle ◽  
Aisi 304 ◽  
Metal Forming Process ◽  
Stage Process

Incremental forming is a non-conventional metal forming process which is widely used to produce the customized parts especially in medical and aerospace industries. One of the challenges encountered in the single stage process is the maximum wall angle of the component that can be formed to a maximum possible depth without fracture. Many strategies have been tried by the researchers in the past to overcome this limitation. The aim of this research work is to investigate the effect of 5 stage incremental forming process in improving the formation of maximum wall angle to a possible height which is not possible in single stage incremental forming. Also, the different strain measurements are carried out to identify the region at which the fracture is likely to occur in the produced part. It is observed from single stage incremental forming process for a wall angle of 64, max. depth of 45mm is achieved in the part produced. The current 5 stage incremental forming process reached the max. height of 54 mm with a wall angle of 76 successfully. The maximum thickness strain of 75% is observed at a distance of 18mm from the bottom end of the flange of a formed component.

On the Effect of Curvature Radius on the Spif-Ability

2010 ◽  
Vol 129-131 ◽  
pp. 1222-1227 ◽  
Author(s):  
Ghulam Hussain ◽  
Gao Lin ◽  
Nasir Hayat ◽  
Asif Iqbal
Keyword(s):  
Sheet Metal Forming ◽  
Metal Forming ◽  
Incremental Forming ◽  
Single Point ◽  
Curvature Radius ◽  
Single Point Incremental Forming ◽  
Test Results ◽  
Forming Process ◽  
Wall Angle ◽  
Metal Forming Process

Single Point Incremental Forming (SPIF) is a novel sheet metal forming process. The formability (i.e. spif-ability) in this process is determined through Varying Wall Angle Conical Frustum (VWACF) test. In this paper, the effect of variation in the curvature radius, a geometrical parameter of test, on the test results is investigated. A series of VWACF tests with a variety of curvature radii is performed to quantify the said effect. It is found that the spif-ability increases with increasing of curvature radius. However, any variation in the curvature radius does not affect the spif-ability when the normalized curvature radius (i.e. curvature radius/tool radius) becomes higher than 9.

Role of Material Properties in Improving Sheet Formability in SPIF Process

2010 ◽  
Vol 139-141 ◽  
pp. 600-604 ◽  
Author(s):  
Ghulam Hussain ◽  
Nasir Hayat ◽  
Lin Gao
Keyword(s):  
Mechanical Properties ◽  
Single Point ◽  
Tensile Fracture ◽  
Forming Process ◽  
Thickness Strain ◽  
Wall Angle ◽  
Wide Range ◽  
Metal Forming Process ◽  
Sheet Formability

Single point incremental forming (SPIF) is a novel sheet metal forming process. Owing to unique deformation mechanism, this process improves the sheet formability as compared to the conventional stamping process. In the current paper, the mechanical properties and spifability (i.e. formability in SPIF) of a wide range of materials were tested. The mechanical properties were mainly determined through tensile testing and the spifability was evaluated using Varying Wall Angle Conical Frustum (VWACF) test. Each mechanical property was drawn against the improvement in sheet formability (i.e. difference of spifability and stampability) and the sole most influential property was identified. It was found that the improvement in formability increases with the increasing of true thickness strain at tensile fracture.

Experimental Tests to Study Feasibility and Formability in Incremental Forming Process

2009 ◽  
Vol 410-411 ◽  
pp. 391-400 ◽  
Author(s):  
Aldo Attanasio ◽  
Elisabetta Ceretti ◽  
Antonio Fiorentino ◽  
Luca Mazzoni ◽  
Claudio Giardini
Keyword(s):  
Tool Path ◽  
Incremental Forming ◽  
Single Point ◽  
Sheet Thickness ◽  
Experimental Tests ◽  
Final Part ◽  
Cnc Machine ◽  
Forming Process ◽  
Metal Forming Process ◽  
Sheet Formability

This paper deals with Incremental Sheet Forming (ISF), a sheet metal forming process, that knew a wide development in the last years. It consists of a simple hemispherical tool that, moving along a defined path by means of either a CNC machine or a robot or a self designed device, locally deforms a metal sheet. A lot of experimental and simulative researches have been conducted in this field with different aims: to study the sheet formability and part feasibility as a function of the process parameters; to define models able to forecast the final sheet thickness as a function of the drawing angle and tool path strategy; to understand how the sheet deforms and how formability limits can be defined. Nowadays, a lot of these topics are still open. In this paper, the results obtained from an experimental campaign performed to study sheet formability and final part feasibility are reported. The ISF tests were conducted deforming FeP04 deep drawing steel sheet 0.8 mm thick and analyzing the influence of the tool path strategy and of the adopted ISF technique (Single Point Incremental Forming Vs. Two Points Incremental Forming). The part feasibility and formability were evaluated considering final sheet thickness, geometrical errors of the final part, maximum wall angle and depth at which the sheet breaks. Moreover, process forces measurements were carried out by means of a specific device developed by the Authors, allowing to obtain important information about the load acting on the deforming device and necessary for deforming sheet.

scholarly journals PROCESS SIMULATION AND QUALITY EVALUATION IN INCREMENTAL SHEET FORMING

2011 ◽  
Vol 12 (3) ◽  
Author(s):  
Meftah Hrairi ◽  
Salah B. M. Echrif
Keyword(s):  
Wall Thickness ◽  
Metal Forming ◽  
Tool Path ◽  
Incremental Forming ◽  
Low Cost ◽  
Single Point ◽  
Single Point Incremental Forming ◽  
Forming Process ◽  
Metal Forming Process ◽  
Complex Parts

Single Point Incremental Forming (SPIF) is a promising sheet-metal-forming process that permits the manufacturing of small to medium-sized batches of complex parts at low cost. It allows metal forming to work in the critical ‘necking-to-tearing' zone which results in a strong thinning before failure if the process is well designed. Moreover, the process is complex due to the number of variables involved. Thus, it is not possible to consider that the process has been well assessed; several remaining aspects need to be clarified. The objective of the present paper is to study some of these aspects, namely, the phenomenon of the wall thickness overstretch along depth and the effect of the tool path on the distribution of the wall thickness using finite element simulations.Abstrak: Pembentukan Tokokan Mata Tunggal (Single Point Incremental Forming (SPIF)) merupakan satu proses pembentukan kepingan logam yang membolehkan pembuatan dalam jumlah yang kecil hingga sederhana, bahagian-bahagian yang kompleks pada kos yang rendah. Jika proses ini direka dengan baik, kaedah ini membolehkan pembentukan logam yang baik terhasil. Jika tidak, semasa peringkat zon kritikal ‘perleheran-ke-pengoyakan' menyebabkan penipisan keterlaluan yang boleh menyebabkan logam tersebut rosak. Tambahan pula, proses ini agak kompleks, kerana ia melibatkan beberapa pemboleh ubah. Maka, walaupun proses ini telah dinilaikan seeloknya; masih terdapat beberapa aspek lain yang perlu diperjelaskan. Objektif kertas ini dibentangkan adalah untuk mengkaji beberapa aspek tertentu, seperti, ketebalan dinding regangan berlebihan di sepanjang kedalaman dan kesan tool path (beberapa siri posisi koordinat untuk menentukan pergerakan alatan memotong ketika operasi memesin) terhadap pengagihan ketebalan dinding menggunakan simulasi unsur terhingga.

scholarly journals Simulation of incremental forming processes of a pyramidal ring made of two materials

2018 ◽  
Vol 19 (3) ◽  
pp. 313
Author(s):  
Masood Ghassabi ◽  
Milad Salimi ◽  
Mohammad Haghpanahi
Keyword(s):  
Feed Rate ◽  
Rotational Speed ◽  
Incremental Forming ◽  
Thickness Distribution ◽  
Single Point ◽  
Dimensional Accuracy ◽  
Cnc Machine ◽  
Forming Force ◽  
Forming Process ◽  
Dimensional Precision

Incremental forming is one of the most well-known forming processes for complex and asymmetric parts. This method uses a CNC machine, simple forming tool, and a die. This study focused on effects of some parameters such as the material, feed rate, pitch, rotational speed and movement strategy of tool on the dimensional precision, forming force, thickness distribution and fracture in the welding area. The results showed that single point incremental forming (SPIF) led to a better thickness distribution with lower tool force, whereas two-point incremental forming led to better dimensional accuracy. Rotational speed does not have any significant impact on the forming process while decreasing the feed rate partially reduced the forming force. According to the results, although dimensional precision in double point incremental forming is better than SPIF, when it comes to the thickness distribution, forming force, and economic issues, SPIF is in favor. The results also showed that by connecting two materials, different parameters for the two materials could be investigated simultaneously in one simulation process.

scholarly journals Common defects of parts manufactured through single point incremental forming

2021 ◽  
Vol 343 ◽  
pp. 04007
Author(s):  
Mihai Popp ◽  
Gabriela Rusu ◽  
Sever-Gabriel Racz ◽  
Valentin Oleksik
Keyword(s):  
Sheet Metal ◽  
Metal Forming ◽  
Incremental Forming ◽  
Single Point ◽  
Single Point Incremental Forming ◽  
Forming Process ◽  
Metal Forming Process ◽  
Serial Robot ◽  
The Many ◽  
Cold Metal

Single point incremental forming is one of the most intensely researched die-less manufacturing process. This process implies the usage of a CNC equipment or a serial robot which deforms a sheet metal with the help of a relatively simple tool that follows an imposed toolpath. As every cold metal forming process, besides the many given advantages it has also some drawbacks. One big drawback in comparison with other cold metal forming processes is the low accuracy of the deformed parts. The aim of this research is to investigate the sheet metal bending mechanism through finite element method analysis. The results shows that the shape of the retaining rings has a big influence over the final geometrical accuracy of the parts manufactured through single point incremental forming.

Experimental and Simulation Study of Single Point Incremental Forming of Polycarbonate

2019 ◽  
Author(s):  
Saurabh Rai ◽  
Rakesh Kumar ◽  
Harish Kumar Nirala ◽  
Kevin Francis ◽  
Anupam Agrawal
Keyword(s):  
Incremental Forming ◽  
Single Point ◽  
Material Strength ◽  
Displacement Curve ◽  
Single Point Incremental Forming ◽  
Aircraft Industry ◽  
Forming Process ◽  
Wall Angle ◽  
Safety Glass ◽  
Force Displacement

Abstract Single point incremental forming (SPIF) is more accurate and economical than the conventional forming process for customized products. Majority of the work in SPIF has been carried out on metals. However, polymers are also required to shape. Polycarbonate has wide application in safety glass, bottles, automotive and aircraft industry due to its transparent as well as attractive processing and mechanical properties as compared to other polymeric plastics. In present work, the Polycarbonate (PC) sheet of thickness 1.8 mm is deformed to make a square cup at different angles. Tensile testing is done to analyze the effect of wall angle on the deformed cup. This work illustrates the effect of the SPIF process on material strength in a different directions (vertical and horizontal) of the final deformed product. Tool forces are evaluated using ABAQUS® simulation for SPIF. Numerical simulation approach is used to calculate the fracture energy, which utilizes the force-displacement curve of the specimen and is verified.

A Two-Pronged Approach for the Assessment of Springback Variability for Sheet Metal Forming Applications

2013 ◽  
Vol 554-557 ◽  
pp. 957-965 ◽  
Author(s):  
Jérémy Lebon ◽  
Guénhaël Le Quilliec ◽  
Rajan Filomeno Coelho ◽  
Piotr Breitkopf ◽  
Pierre Villon
Keyword(s):  
Sheet Metal ◽  
Sheet Metal Forming ◽  
Metal Forming ◽  
Numerical Models ◽  
Low Cost ◽  
Forming Process ◽  
Metal Forming Process ◽  
Small Random Perturbations ◽  
Complex Phenomena ◽  
Bending Under Tension

Springback assessment for sheet metal forming processes is a challenging issue which requires to take into account complex phenomena (physical non linearities and uncertainties). We highlight that the stochastic analysis of metal forming process requires both a high precision and low cost numerical models and propose a two-pronged methodology to address these challenges. The deep drawing simulation process is performed using an original low cost semi-analytical approach based on a bending under tension model with a good accuracy for small random perturbations of the physical and process parameters. The springback variability analysis is performed using an efficient stochastic metamodel, namely a sparse version of the polynomial chaos expansion.

Brass 70/30 and Incremental Sheet Forming Process

2013 ◽  
Vol 554-557 ◽  
pp. 1419-1431 ◽  
Author(s):  
Daniel Fritzen ◽  
Anderson Daleffe ◽  
Jovani Castelan ◽  
Lirio Schaeffer
Keyword(s):  
Incremental Forming ◽  
Single Point ◽  
Sheet Forming ◽  
Incremental Sheet Forming ◽  
Cnc Machining ◽  
Forming Process ◽  
Wall Angle ◽  
Machining Center ◽  
Cad Cam ◽  
Cnc Machining Center

This work addresses through bibliographies and experiments the behavior of sheet brass 70/30 for Incremental Sheet Forming process - ISF, based on the parameters: wall angle (), step vertical (ΔZ) strategy and the way the tool. Experiments based on the method called Single Point Incremental Forming - SPIF. For execution of practical tests, we used the resources: software CAD / CAM, CNC machining center with three axles, matrix incremental, incremental forming tool and a device press sheets. Furthermore, measurement was made of the true deformation () and thickness (s1). Practical tests have shown that the spiral machining strategy yielded a greater wall angle, compared to the conventional strategy outline.

Sign in / Sign up

Export Citation Format

Share Document