scholarly journals The influence of water content on selected physical properties of cereal seeds to improve the precision of DEM simulation

2021 ◽  
Author(s):  
Łukasz Gierz ◽  
Ewelina Kolankowska ◽  
Piotr Markowski
Keyword(s):  
Moisture Content ◽  
Physical Properties ◽  
Initial Moisture Content ◽  
Kernel Weight ◽  
Seed Moisture Content ◽  
Dem Simulation ◽  
Simulation Process ◽  
Winter Cereals ◽  
Influence Of Water ◽  
Length Width

Abstract This article presents the results of research on the influence of moisture on changes in selected physical properties, i.e. the length, width, thickness and weight of dressed and untreated cereal seeds in order to improve the simulation process based on the discrete element method (DEM). The research was conducted on the seeds of three winter cereals, i.e. triticale, rye, and barley. The seeds with an initial moisture content of about 7% were moistened to 5 levels, ranging from 9.5% to 17.5%, at an increment of 2%. The statistical analysis showed that moisture significantly influenced the physical properties of the seeds , i.e. their length, width, thickness, and weight. As the moisture content of the seeds increased, there were greater differences in their weight. The average increase in the thousand kernel weight resulting from the increase in their moisture content ranged from 4 to 6 mg. The change in the seed moisture content from 9.5% to 17.5% significantly increased the volume of rye seeds from 3.10% to 14.99%, the volume of triticale seeds from 1.00% to 13.40%, and the volume of barley seeds from 1.00% to 15.33%. These data can be used as a parameter to improve the DEM simulation process.

scholarly journals Measurements and Analysis of the Physical Properties of Cereal Seeds Depending on Their Moisture Content to Improve the Accuracy of DEM Simulation

2022 ◽  
Vol 12 (2) ◽  
pp. 549
Author(s):  
Łukasz Gierz ◽  
Ewelina Kolankowska ◽  
Piotr Markowski ◽  
Krzysztof Koszela
Keyword(s):  
Moisture Content ◽  
Physical Properties ◽  
Initial Moisture Content ◽  
Kernel Weight ◽  
Seed Moisture Content ◽  
Dem Simulation ◽  
Simulation Process ◽  
Winter Cereals ◽  
Seed Moisture ◽  
Length Width

This article presents the results of research on the influence of moisture on changes in the physical properties, i.e., the length, width, thickness, and weight, of dressed and untreated cereal seeds in order to improve the simulation process based on the discrete element method (DEM). The research was conducted on the seeds of three winter cereals, i.e., triticale, rye, and barley. The seeds with an initial moisture content of about 7% were moistened to five levels, ranging from 9.5% to 17.5%, at an increment of 2%. The statistical analysis showed that moisture significantly influenced the physical properties of the seeds, i.e., their length, width, thickness, and weight. As the moisture content of the seeds increased, there were greater differences in their weight. The average increase in the thousand kernel weight resulting from the increase in their moisture content ranged from 4 to 6 mg. The change in the seed moisture content from 9.5% to 17.5% significantly increased the volume of rye seeds from 3.10% to 14.99%, the volume of triticale seeds from 1.00% to 13.40%, and the volume of barley seeds from 1.00% to 15.33%. These data can be used as a parameter to improve the DEM simulation process.

scholarly journals Forma e tamanho de grãos de soja para diversos teores de água

2018 ◽  
Vol 39 (6) ◽  
pp. 2821
Author(s):  
Wilker Alves Morais ◽  
Osvaldo Resende ◽  
Fernando Nobre Cunha ◽  
Vitor Marques Vidal ◽  
Nelmício Furtado da Silva ◽  
...  
Keyword(s):  
Moisture Content ◽  
Physical Properties ◽  
Surface Area ◽  
Initial Moisture Content ◽  
Correlation Coefficients ◽  
Volumetric Shrinkage ◽  
Linear Regression Models ◽  
Moisture Contents ◽  
Soybean Cultivars ◽  
Grain Moisture

Physical properties of soybean grains present differences as a function of cultivars and moisture content, with the correlation between physical properties. This study aimed to determine the characteristics related to the physical properties of grains with different moisture contents of three soybean cultivars. The experimental design was completely randomized design in a 3 × 6 factorial scheme with three replications, consisting of three soybean cultivars (6266 RSF IPRO, BMX Potência RR, and 14403Z6001) and six grain moisture contents (11, 13, 15, 17, 19, and 21% wb). Soybean grains presented an initial moisture content of 11.0, 11.0, and 10.8% wb, respectively for 6266 RSF IPRO, BMX Potência RR, and 14403Z6001. The other moisture contents were obtained by soaking in a BOD chamber maintained at 25 °C and 93% of relative humidity. We assessed volume, roundness, sphericity, surface area, volumetric shrinkage, and volumetric shrinkage rate. The data were submitted to the analysis of variance by the F-test (p < 0.05) and when significant, regression analysis was performed for grain moisture contents and the means of cultivars were compared by the Tukey’s test. Pearson’s correlation analysis was also carried out to represent the linearity between grain physical properties. The cultivar BMX Potência RR obtained the highest results for volume, roundness, sphericity, and surface area. Volume and surface area increased as the moisture content of soybean grains increased; the opposite was observed for roundness and sphericity. A linear increase in volumetric shrinkage was observed as moisture content increased. The values of the correlation coefficients of the linear regression models can be used to describe the relationships between physical properties.

MOISTURE-DEPENDENT PHYSICAL PROPERTIES OF MEDICAL TINY SEEDS: PART A: FLIXWEED (DESCURAINIA SOPHIA L.)

2021 ◽  
Vol 24 (1) ◽  
Author(s):  
Amir Hossein Mirzabe ◽  
◽  
Ali Fadavi ◽  
Ali Mansouri ◽  
◽  
...  
Keyword(s):  
Moisture Content ◽  
Physical Properties ◽  
Surface Area ◽  
Particle Density ◽  
Arithmetic Mean ◽  
Angle Of Repose ◽  
Projected Area ◽  
Angle Of Friction ◽  
Mean Diameter ◽  
Length Width

Knowledge of agricultural seeds’ physical properties has significant importance for machinery and processing equipment design. Physical properties of flixweed (Descur ainia sophia L.) seeds were determined as a function of moisture content. Several properties were studied in the moisture range from 5.28 to 17.53% dry basis. Also, probability distribution of seeds’ principal dimensions were modeled by Gamma, Generalized Extreme Value, Lognormal, and Weibull functions. With increasing moisture content from 5.28 to 17.53%, properties including; length, width, thickness, geometric and arithmetic mean diameter, sphericity, specific surface area, volume, and projected area showed no specific trend. In contrast, the surface area increased from 6×10-7 to 1×10-6 m2. The bulk and particle density decreased from 696.61 to 542.51 kg·m-3, and 1217.50 to 1189.02 kg·m-3, respectively. The porosity increased from 42.78 to 54.37%. The maximum external static angle of friction belonged to wood at all moisture content levels, followed by the iron and galvanized surfaces. At all moisture levels, the emptying angle of repose was more than the filling one.

Moisture Dependent Selected Engineering Properties of Deenanath Seeds in Relation to Development of Processing Machinery

2021 ◽  
Vol 58 (03) ◽  
pp. 250-261
Author(s):  
Sanjay Kumar Singh ◽  
Sheshrao Kautkar ◽  
P. K. Pathak ◽  
Bholuram Gurjar ◽  
Sunil Swami ◽  
...  
Keyword(s):  
Moisture Content ◽  
Physical Properties ◽  
Geometric Mean ◽  
Seed Mass ◽  
Correlation Coefficients ◽  
Engineering Properties ◽  
True Density ◽  
Linear Relationships ◽  
Mean Diameter ◽  
Length Width

Propagation of grasses through seeds is important in view of vigour and germination. Various grasses as Pennisetum pedicellatum Trin., Cenchrus ciliaris L., Chrysopogan fulvus have lower vigour and germination, due to which they need specific operations as defluffing, separation of true seeds, cleaning and grading by specific machines. In designing a machine for a specific use, physical properties and their behaviour with moisture play an important role. A study was conducted to assess the effect of moisture content at five levels [6.88 - 19.23 %, (d.b.)] on selected physical properties of defluffed Deenanath grass seed. The length, width, thickness, arithmetic mean diameter, and geometric mean diameter of defluffed Deenanath seed increased from 2.30 mm to 2.56 mm, 0.71 mm to 0.96 mm, 0.47 mm to 0.63 mm, 1.16 mm to 1.38 mm, and 0.90 mm to 1.15 mm, respectively, with increase in moisture content 6.88 % to 19.23 %. Bulk density, true density, and porosity decreased from 652.16 kg.m-3 to 585.78 kg.m-3, 852.63 kg.m-3 to 792.71 kg.m-3, and 25.62 % to 24.97 %, respectively, with increase in moisture content from 6.88 % to 19.23 per cent. The aspect ratio, sphericity, surface area, volume, and thousand-seed mass of the seed were in the range of 30.91 - 37.51 %, 0.39 - 0.45, 2.58 - 3.23 mm2 , 3.71 - 4.97 mm3 , and 0.480 - 0.523 g, respectively. Linear relationships with correlation coefficients higher than 0.90 were observed for the physical properties over the experimental range of moisture content.

scholarly journals Physical properties of safflower grains. Part I: Geometric and gravimetric characteristics

2017 ◽  
Vol 21 (5) ◽  
pp. 344-349 ◽  
Author(s):  
Elton A. S. Martins ◽  
André L. D. Goneli ◽  
Cesar P. Hartmann Filho ◽  
Munir Mauad ◽  
Valdiney C. Siqueira ◽  
...  
Keyword(s):  
Moisture Content ◽  
Physical Properties ◽  
Bulk Density ◽  
Surface Area ◽  
Initial Moisture Content ◽  
Volume Ratio ◽  
True Density ◽  
Geometrical Characteristics ◽  
Forced Air ◽  
Air Circulation

ABSTRACT Safflower is an oil crop and its oil can be used for food and industrial purposes. However, there is little information about the physical properties of these grains, which is important for the planning and execution of post-harvest stages. Thus, this study was carried out with the aim of evaluating the effect of drying on the main physical properties of safflower grains. Safflower grains were harvested with an initial moisture content of approximately 0.445 decimal d.b. (dry basis) and subjected to drying in an oven with forced air circulation at 40 °C, until the grains reached a final moisture content of 0.073 ± 0.008 decimal d.b. During the drying, bulk density and true density, porosity, thousand-grain mass, circularity, sphericity, projected and surface area, and surface-volume ratio were measured. Based on these results, it is concluded that all gravimetric and geometrical characteristics of safflower grains were reduced due to the reduction of moisture content, except for the surface-volume ratio.

scholarly journals Efeito da secagem nas propriedades físicas dos grãos de feijão adzuki

2016 ◽  
Vol 37 (6) ◽  
pp. 3871
Author(s):  
Udenys Cabral Mendes ◽  
Osvaldo Resende ◽  
Juliana Rodrigues Donadon ◽  
Dieimisson Paulo Almeida ◽  
Anísio Correa da Rocha ◽  
...  
Keyword(s):  
Moisture Content ◽  
Physical Properties ◽  
Surface Area ◽  
Volume Ratio ◽  
Adzuki Bean ◽  
Projected Area ◽  
Air Ventilation ◽  
Length Width ◽  
Forced Air ◽  
Drying Conditions

The goal of the present study was to assess the effect of drying on the physical properties of adzuki bean (Vigna angularis Willd.). Adzuki beans with moisture content of 47.9% were dried in a oven with forced air ventilation at temperatures of 40, 60 and 80 °C and relative humidity of 18.5, 8.6, and 3.8%, respectively, until the moisture content reached 12.9%. We used 15 adzuki beans individualised in aluminium capsules. The orthogonal axes of the beans (length, width, and thickness) were measured at intervals of five percentage points during the reduction of moisture content. The parameters determined were: sphericity; circularity; volume of beans; volumetric contraction index; volume contraction percentage; surface area; projected area; and surface-volume ratio. The drying conditions altered the physical properties of adzuki bean. As a result of moisture content reduction, there was increased sphericity and surface-volume ratio, and decreased volume, unitary volumetric contraction, surface area, and projected area. Circularity was not influenced by the drying temperatures within the range of moisture content analysed.

scholarly journals Physical properties of sunflower seeds during drying

2017 ◽  
Vol 38 (1) ◽  
pp. 157
Author(s):  
Thaís Adriana de Souza Smaniotto ◽  
Osvaldo Resende ◽  
Kelly Aparecida de Sousa ◽  
Rafael Cândido Campos ◽  
Denner Nogueira Guimarães ◽  
...  
Keyword(s):  
Moisture Content ◽  
Physical Properties ◽  
Bulk Density ◽  
Initial Moisture Content ◽  
Gravimetric Method ◽  
Terminal Velocity ◽  
True Density ◽  
Sunflower Seeds ◽  
Intergranular Porosity ◽  
Air Ventilation

The aim of this work was to determine the effect that the moisture content has on the physical properties of sunflower seeds. The cultivar Olisun 3, with an initial moisture content of 34.1 (% wb), was used and then subjected to drying in an oven with forced air ventilation under three temperature conditions: 40, 60 and 80 °C. The reduction in the moisture content during drying was monitored by the gravimetric method until it reached a final moisture content of 8.0 ± 1.0 (% wb). The physical properties were analysed: the bulk density, true density, intergranular porosity and volumetric shrinkage of the mass and unit and terminal velocity. The reduction in the moisture content influenced the physical properties of sunflower seeds and caused a decrease in the intergranular porosity, bulk density and true density at all examined temperatures. The mass and volumetric contractions of the unit and reduction in shrinkage rates all increased with the drying of sunflower seeds at all studied temperatures. The terminal velocity increased as the moisture content of the grains increased, which was more evident at the drying temperature of 80 °C.

Physical Properties of Naked Oat Seeds (Avena nuda L.)

2014 ◽  
Vol 10 (2) ◽  
pp. 339-345 ◽  
Author(s):  
Guang-yue Ren ◽  
Ping Yao ◽  
Nan Fu ◽  
Dong Li ◽  
Yubin Lan ◽  
...  
Keyword(s):  
Moisture Content ◽  
Physical Properties ◽  
Geometric Mean ◽  
Static Friction ◽  
Angle Of Repose ◽  
Naked Oat ◽  
Oat Seeds ◽  
Avena Nuda ◽  
Length Width ◽  
Content Range

Abstract Some physical properties of the naked oat seeds were determined as a function of moisture content ranging from 9.56 to 18.07% (wet basis, w.b.). Seed length, width, thickness, and geometric mean diameter were increased from 7.89 to 8.81 mm, 2.32 to 3.09 mm, 1.85 to 2.77 mm, and 3.24 to 4.22 mm, respectively, with the increase of moisture content. The bulk and true densities of the seed samples were decreased from 682.1 to 533.1 kg/m3 and from 1,280.6 to 1,162.8 kg/m3, respectively. The average static friction coefficients of the seeds on the surfaces of plywood, stainless steel, and polypropylene knitted bags were increased from 0.403 to 0.674, from 0.371 to 0.496, and from 0.562 to 0.765, respectively, when the moisture content of these samples were increased from 9.56 to 18.07% (w.b.). The static angle of repose varied from 24.38° to 39.17° in the moisture content range.

scholarly journals Model Dinamik Vigor Daya Simpan Benih Kedelai pada Penyimpanan Terbuka

2016 ◽  
Vol 34 (3) ◽  
pp. 219
Author(s):  
Ari Wahyuni ◽  
M. R. Suhartanto ◽  
Abdul Qadir
Keyword(s):  
Moisture Content ◽  
Initial Moisture Content ◽  
Seed Viability ◽  
Soybean Seed ◽  
Storage Period ◽  
Seed Storage ◽  
Seed Moisture Content ◽  
Seed Moisture ◽  
Input Model ◽  
Seed Storability

<p>Soybean seed viability declines during seed storage. Soybean seed deteriorates rapidly, affected by its high protein content and often high humidity in the tropical environment. This research was aimed to develop dynamic model of soybean seed viability in an open storage. The study was conducted in three stages, namely: 1) desk study, 2) seed storage experiment, 3) development of seed storage model, simulation and verification of the model. The second stage of the experiment consisted of soybean seed storing and germination testing using completely randomized design. Treatments were three initial moisture content (7-8%, 9-10% and 11-12%) and four varieties of soybean (Anjasmoro, Wilis, Detam-1 and Detam-2). The results showed that the seed behaviour during storage period were affected by initial seed moisture content, initial viability, varieties and environmental condition. Therefore, seed moisture content, initial viability and varieties may be used as input model. Moisture content, integreting seed respiration, electric conductivity and seed storability vigor (VDSDB) were as model output. Simulation of Seed Storability Vigor Prediction Model with Model Construction Layer-Stella (MCLS) using relative humidity (RH), temperature, seed permeability, initial moisture content and initial viability as input model could logically predict the seed moisture content and seed storability vigor (VDSDB).</p>

Physical properties and compression loading behaviour of corn seed

2013 ◽  
Vol 27 (2) ◽  
pp. 119-126 ◽  
Author(s):  
Lj. Babić ◽  
M. Radojèin ◽  
I. Pavkov ◽  
M. Babić ◽  
J. Turan ◽  
...  
Keyword(s):  
Moisture Content ◽  
Physical Properties ◽  
Modulus Of Elasticity ◽  
Compressive Loading ◽  
Secant Modulus ◽  
Seed Moisture Content ◽  
Mean Values ◽  
Compression Loading ◽  
Corn Seed ◽  
Dent Corn

Abstract The aim of this study was to acquire data on the physical properties and compression loading behaviour of seed of six corn hybrid varieties. The mean values of length, width, thickness, geometric diameter, surface area, porosity, single kernel mass, sphericity, bulk and true density, 1 000 kernelmass and coefficient of friction were studied at single level of corn seed moisture content. The calculated secant modulus of elasticity during compressive loading for dent corn was 0.995 times that of the semi-flint type; there were no significant differences in the value of this mechanical property between semi-flint and dent corn varieties. The linear model showed a decreasing tendency of secant modulus of elasticity for all hybrids as the moisture content of seeds increased.

Sign in / Sign up

Export Citation Format

Share Document