scholarly journals Hen feather a bio-waste material for adsorptive removal of methyl red dye from aqueous solutions

2021 ◽  
Author(s):  
Samina Zaman ◽  
Md. Nayeem Mehrab ◽  
Md. Shahnul Islam ◽  
Gopal Chandra Ghosh ◽  
Tapos Kumar Chakraborty
Keyword(s):  
Aqueous Solutions ◽  
Contact Time ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Methyl Red ◽  
Experimental Conditions ◽  
Potential Applicability ◽  
Pseudo Second Order ◽  
Red Dye ◽  
Adsorbent Dose

Abstract This study investigates the potential applicability of hen feather (HF) to remove methyl red (MR) dye from aqueous solution with the variation of experimental conditions: contact time (1–180 min), pH (4–8), initial dye concentration (5–50 mg/L) and adsorbent dose (3–25 g/L). Scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR) evaluate the surface morphology and chemistry of HF, respectively. The maximum removal of MR by HF was 92% when the optimum conditions were initial MR dye concentration 05 mg/L, pH 4.0, adsorbent dose 07.0 g/L and 90.0 min equilibrium contact time. Langmuir isotherm (R2 = 0.98) was more suited than Freundlich isotherm (R2 = 0.96) for experimental data, and the highest monolayer adsorption capacity was 6.02 mg/g. The kinetics adsorption data fitted well to pseudo-second-order model (R2 = 0.999) and more than one process were involved during the adsorption mechanism but film diffusion was the potential rate-controlling step. The findings of the study show that HF is a very effective and low-cost adsorbent for removing MR dye from aqueous solutions.

scholarly journals Aqueous Phase Adsorption of Pb (II) Ions onto Hymenoptera sphecidae (Mud-wasp) Nest

2020 ◽  
pp. 21-31
Author(s):  
Donald T. Kukwa ◽  
Peter A. Adie ◽  
Rose E. Kukwa ◽  
Paula D. Kungur
Keyword(s):  
Contact Time ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Batch Process ◽  
Second Order ◽  
Order Kinetic ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Best Fit ◽  
Adsorbent Dose

Removal of Pb (II) ion from aqueous solution using Hymenoptera sphecidae (mud-wasp) nest was investigated using a batch process. The effect of pH, contact time and adsorbent dose were also investigated. The result showed that the adsorption of Pb (II) ion onto mud-wasp nest was dependent on pH, contact time and adsorbent dose. Adsorption patterns were analysed in terms of three bi-parameter isotherms of Langmuir, Freundlich and Temkin. Freundlich isotherm gave the best fit to the adsorption data with a correlation coefficient of 0.992, while monolayer sorption capacity yielded 41.667 mg/g. Lagergren’s pseudo first-order and pseudo second-order kinetic models were used to test the adsorption kinetics. The kinetic data were well described by the pseudo second-order kinetic model, suggesting that the process was chemisorption type.  The results showed that mud-wasp nest can be used as a low-cost adsorbent for the removal of Pb (II) ion from aqueous solutions.

Sorption of Acid Blue 9 on to Wheat Bran: Optimization, Equilibrium and Kinetic Studies

2010 ◽  
Vol 5 (1) ◽  
Author(s):  
Rajeshkannan Rajan ◽  
Manivasagan Rajasimman ◽  
Rajamohan Natarajan
Keyword(s):  
Wheat Bran ◽  
Contact Time ◽  
Freundlich Isotherm ◽  
Kinetic Studies ◽  
Agitation Speed ◽  
Initial Substrate ◽  
Pseudo Second Order ◽  
Langmuir And Freundlich Equations ◽  
Acid Blue ◽  
Adsorbent Dose

In this study, the use of wheat bran as a possible adsorbent has been successfully demonstrated in the removal of Acid blue9 (AB9) from aqueous solution. The effect of different parameters such as temperature, adsorbent dose, contact time, adsorbent size and agitation speed were investigated. The optimum conditions obtained from response surface methodology are: temperature-38.1°C, adsorbent dose (3.1g/L), contact time (206 min), adsorbent size 0.1mm (150mesh), and agitation speed (222rpm). The effect of pH and initial substrate concentration were studied. The pseudo-first order and pseudo-second order kinetics were tested. The sorption equilibrium, expressed by the Langmuir and Freundlich equations, indicated that the process was in compliance with Freundlich isotherm.

scholarly journals Study of Adsorption Characteristics a Low-Cost Sawdust for the Removal of Direct Blue 85 Dye from Aqueous Solutions

2018 ◽  
Vol 18 (4) ◽  
pp. 724
Author(s):  
Rahmah Hashim Abdullah ◽  
Amjed Mirza Oda ◽  
Alaa Rasheed Omran ◽  
Ameer Salem Mottaleb ◽  
Teeba Mudhefer Mubarakah
Keyword(s):  
Particle Size ◽  
Aqueous Solutions ◽  
Correlation Coefficient ◽  
Adsorption Isotherms ◽  
Contact Time ◽  
Positive Impact ◽  
Low Cost ◽  
Experimental Conditions ◽  
Adsorbent Dosage ◽  
Direct Blue

The performance sawdust as a low cost adsorbent to remove Direct Blue 85 (DB85) dye from aqueous solutions has been evaluated. The characteristic of sawdust analyzed by FTIR and XRD. The removal percentage of this dye was studied at different experimental conditions such as contact time, adsorbent dosage, particle size, temperature, and pH. The optimum removal percentage value was found at pH 2.Temperature also has a positive impact on adsorption, where the adsorption of this dye on the sawdust increased as the temperature increased. High values of correlation coefficient signified that the adsorption of (DB85) dye on the surface of sawdust obey Langmuir and Freundlich adsorption isotherms.

scholarly journals Adsorption of hexavalent chromium ions from aqueous solutions using nano-chitin: kinetic, isotherms and thermodynamic studies

2021 ◽  
Vol 16 (2) ◽  
pp. 436-451
Author(s):  
Meghdad Sheikhi ◽  
Hassan Rezaei
Keyword(s):  
Aqueous Solutions ◽  
Correlation Coefficient ◽  
Hexavalent Chromium ◽  
Contact Time ◽  
New Technology ◽  
Kinetic Studies ◽  
Chromium Vi ◽  
Effects Of Ph ◽  
Pseudo Second Order ◽  
Adsorbent Dose

Abstract Treatment of the industrial wastewater before discharging into aquatic ecosystems using a new technology such as nanotechnology seems necessary. There are different methods for the removal of the heavy metals in the wastewater. In this study, nano-chitin was purchased from the Nano-Novin Polymer Company and used as an adsorbent for the removal of chromium (VI) ions from aqueous solution in a batch system. The effects of pH, temperature, contact time, concentration, and adsorbent dose were investigated. According to the results, the optimum conditions of adsorption occurred at pH = 6, temperature = 25 °C, 60 minutes contact time, and 0.6 g·L−1 adsorbent dose. Investigation of equilibrium isotherms showed that the isotherm fitted the Freundlich model with a correlation coefficient of R2 = 0.9689. The pseudo second-order model with the larger correlation coefficient had a greater fitness against experimental data in the kinetic studies. Thermodynamic parameters such as Gibbs free energy, enthalpy, and entropy were calculated, which indicated spontaneous, endothermic, and random processes, respectively. Given the good results of this project, nano-chitin can be suggested as a novel adsorbent which is highly capable of adsorbing hexavalent chromium from aqueous solutions.

scholarly journals Kinetic and Thermodynamic Study of Adsorption of Copper (II) Ion on Moroccan Clay

2019 ◽  
Vol 9 (2) ◽  
pp. 102-115
Author(s):  
Hanane Essebaai ◽  
Ilham Ismi ◽  
Ahmed Lebkiri ◽  
Said Marzak ◽  
El Housseine Rifi
Keyword(s):  
Contact Time ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
X Ray Diffraction ◽  
X Ray ◽  
Increase With Increase ◽  
Monolayer Adsorption ◽  
Pseudo Second Order ◽  
Kinetics Of ◽  
Kinetic And Thermodynamic Study

Highly efficient low-cost adsorbent was applied for copper (II) ions uptake from aqueous solution. Characteristics of natural adsorbent were established using scanning X-ray diffraction (XRD), X-ray fluorescence, electron microscope (SEM) and Fourier Transform Infra-Red (FTIR). Various physicochemical parameters such as contact time, initial copper(II) ions concentration, adsorbent dosage, pH of copper (II) ions solution and temperature were investigated. The result showed that the adsorption of copper (II) ions by natural clay was favorable at pH=5,5. The adsorption was found to increase with increase in initial copper (II) ions concentration, and contact time. Equilibrium adsorption data were fitted using three isotherms and kinetic data tested with four kinetic models. Freundlich isotherm best described the adsorption of copper (II) ions onto utilised clay, the maximum monolayer adsorption capacity (qmax) was 8 mg/g. Pseudo-second-order model best described the kinetics of the adsorption process. Thermodynamic parameters such as Gibbs free energy, enthalpy and entropy were determined. It was found that copper (II) ions adsorption was spontaneous (ΔG°<0) and endothermic (ΔH°>0).

Removal of Mercury From Aqueous Solutions by ETS-4 Microporous Titanosilicate: Effect of Contact Time, Titanosilicate Mass and Initial Metal Concentration

2007 ◽  
Author(s):  
C. B. Lopes ◽  
M. Otero ◽  
Z. Lin ◽  
E. Pereira ◽  
C. M. Silva ◽  
...  
Keyword(s):  
Heavy Metals ◽  
Aqueous Solutions ◽  
Contact Time ◽  
Sorption Process ◽  
Exchange Equilibrium ◽  
Toxic Heavy Metals ◽  
Experimental Conditions ◽  
Freundlich Isotherms ◽  
Pseudo Second Order ◽  
Microporous Titanosilicate

Mercury is one of the most toxic heavy metals present in the environment and therefore is extremely important develop new, simple and reliable techniques for its removal from aqueous solutions. A recent line of research within this context is the application of microporous materials. The use of these materials for removing heavy metals from solutions may become a potential clean-up technology in the field of wastewater treatment. In this work it is reported the application of microporous titanosilicate ETS-4 as ion exchanger to remove Hg2+ from aqueous solution. Under batch conditions, we studied the effect of contact time, titanosilicate mass and initial Hg2+ concentration. Only 5 mg of ETS-4 are required to purify 2 litres of water with 50 μg L−1 of metal. Under the experimental conditions, the initial Hg2+ concentration and ETS-4 mass have strong influence on the sorption process, and it is proved that 24 h are almost always sufficient to attain ion exchange equilibrium. Langmuir and Freundlich isotherms were used to fit equilibrium experimental results. The kinetics of mercury removal was reliably described by a pseudo second-order model. On the whole, ETS-4 shows considerable potential to remove Hg2+ from wastewaters.

Removal of Congo red dye from aqueous solutions using a halloysite-magnetite-based composite

2016 ◽  
Vol 73 (9) ◽  
pp. 2132-2142 ◽  
Author(s):  
F. Ferrarini ◽  
L. R. Bonetto ◽  
Janaina S. Crespo ◽  
M. Giovanela
Keyword(s):  
Aqueous Solutions ◽  
Adsorption Kinetics ◽  
Congo Red ◽  
Contact Time ◽  
High Efficiency ◽  
Dye Adsorption ◽  
Order Model ◽  
Congo Red Dye ◽  
Pseudo Second Order ◽  
Red Dye

Adsorption has been considered as one of the most effective methods to remove dyes from aqueous solutions due to its ease of operation, high efficiency and wide adaptability. In view of all these aspects, this study aimed to evaluate the adsorption capacity of a halloysite-magnetite-based composite in the removal of Congo red dye from aqueous solutions. The effects of stirring rate, pH, initial dye concentration and contact time were investigated. The results revealed that the adsorption kinetics followed the pseudo-second-order model, and equilibrium was well represented by the Brunauer–Emmett–Teller isotherm. The thermodynamic data showed that dye adsorption onto the composite was spontaneous and endothermic and occurred by physisorption. Finally, the composite could also be regenerated at least four times by calcination and was shown to be a promising adsorbent for the removal of this dye.

Removal of Reactive Black 5 from wastewater using natural clinoptilolite modified with apolaccase

Clay Minerals ◽  
2015 ◽  
Vol 50 (1) ◽  
pp. 65-76 ◽  
Author(s):  
Hayrunnisa Nadaroglu ◽  
Ekrem Kalkan ◽  
Neslihan Celebi ◽  
Esen Tasgin
Keyword(s):  
Thermodynamic Parameters ◽  
Contact Time ◽  
Low Cost ◽  
Dye Adsorption ◽  
Freundlich Isotherm ◽  
Second Order ◽  
Isotherm Models ◽  
Reactive Black 5 ◽  
Pseudo Second Order ◽  
Natural Clinoptilolite

AbstractIn this study, a clinoptilolite modified with apolaccase was used to adsorb Reactive Black 5 (RB5) dye from aqueous solution using the batch procedure. The influences of pH, contact time, temperature and absorbent dosage on the adsorption were investigated. The optimum adsorption was obtained at pH = 6, contact time = 60 min, temperature = 25ºC and adsorbent dosages of 1.62 and 1.59 mg/50 mL per gram of clinoptilolite and of apolaccase-modified clinoptilolite (LMC), respectively). The adsorption experimental data fitted both the Langmuir and Freundlich isotherm models well. In addition, pseudo-first-order and pseudo-second-order kinetics were used to study the kinetics of RB5 dye adsorption onto natural clinoptilolite and LMC. Adsorption appears to follow pseudo-second-order kinetics with a high correlation coefficient. Thermodynamic parameters such as changes in the free energy (ΔG°), enthalpy (ΔH°) and entropy (ΔS°) of adsorption were calculated. The thermodynamic parameters indicate that the adsorption of RB5 dye onto LMC was less spontaneous, feasible and endothermic. The LMC can be used as an alternative low-cost adsorbent for the dye removal from aqueous solutions.

Biosorption of Cu2+ from Aqueous Solutions Using NaOH-Modified Fir Sawdust

2013 ◽  
Vol 726-731 ◽  
pp. 1827-1832
Author(s):  
Hong Mei Deng ◽  
Yong Heng Chen ◽  
Cui Qin Wu ◽  
Xue Xia Huang ◽  
Tao Liu
Keyword(s):  
Aqueous Solutions ◽  
Adsorption Process ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Factors Affecting ◽  
Langmuir Adsorption ◽  
Adsorption Processes ◽  
Equilibrium Data ◽  
Pseudo Second Order ◽  
Agricultural Material

Fir sawdust, a low-cost residual agricultural material, was used as adsorbent for the removal of Cu2+from aqueous solutions. Factors affecting the adsorption behavior of Cu2+, such as pH, initial metal concentration, contact time and temperature, have been carried out. The Cu2+removal was pH-dependent, reaching a maximum at pH 5. The adsorption capacity of the fir sawdust from Langmuir adsorption isotherm was 38.6 mg/g at 25°C. The adsorption process followed pseudo-second-order kinetics. The equilibrium data fitted very well to the Freundlich isotherm. The negative ΔGovalues at various temperatures confirm that the adsorption processes are spontaneous.

Adsorption of methylene blue from aqueous solutions using water treatment sludge modified with sodium alginate as a low cost adsorbent

2016 ◽  
Vol 75 (2) ◽  
pp. 281-295 ◽  
Author(s):  
Hamid Poormand ◽  
Mostafa Leili ◽  
Marzieh Khazaei
Keyword(s):  
Methylene Blue ◽  
Water Treatment ◽  
Aqueous Solutions ◽  
Sodium Alginate ◽  
Contact Time ◽  
Low Cost ◽  
Drinking Water Treatment ◽  
Water Treatment Sludge ◽  
Maximum Sorption Capacity ◽  
Adsorbent Dose

In this research, aluminum-based drinking water treatment sludge is used as a starting material and immobilized by sodium alginate to develop low cost adsorbent for the removal of methylene blue (MB) from aqueous solutions. The studied variables included pH, adsorbent dose, initial MB concentration and contact time. Characteristics of the adsorbent were also studied using scanning electron microscopy and Fourier transform infrared spectroscopy (FTIR). It was revealed from kinetic tests that removal efficiency of MB was 88.5% under the optimum conditions of pH 8, initial MB concentration of 50 mg/L, contact time of 60 min, and adsorbent dose of 0.3 g/L. The oxygen functional groups such as –OH, C–O–C and C=O were found on the surface of developed adsorbent by FTIR. In addition, the adsorption data fitted well the Langmuir adsorption model with the maximum sorption capacity of 909.1 mg/g, and followed the pseudo-second-order kinetics. Findings of this study indicate that the prepared adsorbent is promising for further development of an effective and economical adsorbent material in the near future.

Sign in / Sign up

Export Citation Format

Share Document