scholarly journals Kinetic and Thermodynamic Study of Adsorption of Copper (II) Ion on Moroccan Clay

2019 ◽  
Vol 9 (2) ◽  
pp. 102-115
Author(s):  
Hanane Essebaai ◽  
Ilham Ismi ◽  
Ahmed Lebkiri ◽  
Said Marzak ◽  
El Housseine Rifi
Keyword(s):  
Contact Time ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
X Ray Diffraction ◽  
X Ray ◽  
Increase With Increase ◽  
Monolayer Adsorption ◽  
Pseudo Second Order ◽  
Kinetics Of ◽  
Kinetic And Thermodynamic Study

Highly efficient low-cost adsorbent was applied for copper (II) ions uptake from aqueous solution. Characteristics of natural adsorbent were established using scanning X-ray diffraction (XRD), X-ray fluorescence, electron microscope (SEM) and Fourier Transform Infra-Red (FTIR). Various physicochemical parameters such as contact time, initial copper(II) ions concentration, adsorbent dosage, pH of copper (II) ions solution and temperature were investigated. The result showed that the adsorption of copper (II) ions by natural clay was favorable at pH=5,5. The adsorption was found to increase with increase in initial copper (II) ions concentration, and contact time. Equilibrium adsorption data were fitted using three isotherms and kinetic data tested with four kinetic models. Freundlich isotherm best described the adsorption of copper (II) ions onto utilised clay, the maximum monolayer adsorption capacity (qmax) was 8 mg/g. Pseudo-second-order model best described the kinetics of the adsorption process. Thermodynamic parameters such as Gibbs free energy, enthalpy and entropy were determined. It was found that copper (II) ions adsorption was spontaneous (ΔG°<0) and endothermic (ΔH°>0).

Adsorption of 2,4,6-trichlorophenol on bentonite modified with benzyldimethyltetradecylammonium chloride

2019 ◽  
Author(s):  
Chem Int
Keyword(s):  
Infrared Spectroscopy ◽  
Contact Time ◽  
Removal Rate ◽  
Organic Pollutant ◽  
Freundlich Isotherm ◽  
Solution Concentration ◽  
Isotherm Models ◽  
X Ray Diffraction ◽  
X Ray ◽  
Pseudo Second Order

The objective of this study is to evaluate the performance and capacities of the bentonite of Maghnia, modified with benzyldimethyltetradecylammonium chloride, to remove the organic pollutant 2,4,6-Trichlorophenol (TCP). The modified sample was studied by X-ray diffraction (XRD) technique, infrared spectroscopy (FTIR), and thermogravimetric analysis (TGA) methods. The best removal rate (99.52%) was obtained at 19°C, pH 4, solution concentration of 50 mg/L, stirring speed of 180 rpm and contact time of 60 min. The results were well fitted by both Langmuir and Freundlich isotherm models and the pseudo-second-order is the best model to describe the process.

scholarly journals Removal of Pb(II) from aqueous solutions using Acacia Nilotica seed shell ash supported Ni0.5Zn0.5Fe2O4 magnetic nanoparticles

2016 ◽  
Vol 6 (4) ◽  
pp. 562-573 ◽  
Author(s):  
Farshad Omidvar-Hosseini ◽  
Farid Moeinpour
Keyword(s):  
Magnetic Nanoparticles ◽  
Low Cost ◽  
Acacia Nilotica ◽  
Environmentally Benign ◽  
Order Kinetic ◽  
X Ray Diffraction ◽  
X Ray ◽  
Monolayer Adsorption ◽  
Order Kinetic Model ◽  
Pseudo Second Order

Acacia Nilotica seed shell ash supported Ni0.5Zn0.5Fe2O4 magnetic nanoparticles were synthesized by a low-cost, simple, and environmentally benign procedure. The adsorbent was characterized by several methods including X-ray diffraction, scanning electron microscopy and Fourier transform infrared spectroscopy. Then, the potential of Acacia Nilotica seed shell ash supported Ni0.5Zn0.5Fe2O4 magnetic nanoparticles was investigated for adsorption of Pb(II). The effect of different parameters including contact time, pH, adsorbent dosage and initial Pb(II) concentration on the Pb(II) removal yield was studied. The experimental data were fitted well with the pseudo-second order kinetic model (R2 = 0.999). The adsorption isotherm was described well by the Langmuir isotherm (R2 = 0.900) with a maximum monolayer adsorption capacity of 37.6 mg g–1. The process for purifying water treatment presented here is easy using the magnetic nanoparticles. Therefore, this adsorbent was found to be useful and valuable for controlling water pollution due to Pb(II) ions.

scholarly journals Equilibrium and Kinetic Study of Removal Copper(II) from Aqueous Solution Using Chicken Eggshells: Low Cost Sorbent

Molekul ◽  
2021 ◽  
Vol 16 (1) ◽  
pp. 28
Author(s):  
Mohammad Jihad Madiabu ◽  
Joko Untung ◽  
Imas Solihat ◽  
Andi Muhammad Ichzan
Keyword(s):  
Aqueous Solution ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Sorption Process ◽  
X Ray Diffraction ◽  
Order Model ◽  
X Ray ◽  
Adsorption Condition ◽  
Pseudo Second Order ◽  
Effect Of Copper

The research aims to investigate feasibility eggshells as potential adsorbent to remove copper(II) ions from aqueous solution. Eggshells powder was characterized using X-ray diffraction, scanning electron microscopy, and Fourier transform infrared spectroscopy. Effect of copper(II) initial concentration, adsorbent dosage, and contact time have conducted. The optimum adsorption condition obtained when 0.7 g eggshells applied to 50 mg/L copper(II) solution for 50 minutes. The maximum percentage of copper(II) removal was exceeded more than 85%. Langmuir and Freundlich isotherm model were applied to describe the equilibrium adsorption. Copper(II) kinetics sorption process was fitted to pseudo-second order model with a rate constant equal to 0.516 g/mg.min. The results clearly exhibit that eggshells powder can be effectively used to remove copper(II) ions from aqueous solutions.

scholarly journals Selective adsorption of PHC and regeneration of washing effluents by modified diatomite

2020 ◽  
Vol 81 (10) ◽  
pp. 2066-2077
Author(s):  
Zhuoqi Xu ◽  
Gengbo Ren ◽  
Yanying Zhu ◽  
Xiaodong Ma ◽  
Hongrui Li ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Selective Adsorption ◽  
Low Cost ◽  
Soil Washing ◽  
X Ray Diffraction ◽  
X Ray ◽  
Monolayer Adsorption ◽  
Pseudo Second Order ◽  
Adsorption Desorption ◽  
Modified Diatomite

Abstract Selective removal of petroleum hydrocarbons (PHCs) from soil washing effluents is the key to the surfactant-enhanced soil washing technology. In this study, the diatomite was modified by nonionic surfactant TX-100 and applied in the selective adsorption of PHCs in the soil washing effluents. The modified diatomites were characterized by scanning electron microscopy, Fourier transform infrared spectroscopy, X-ray diffraction, N2 adsorption/desorption and X-ray photoelectron spectroscopy respectively. The adsorption process followed the pseudo-second-order model and the adsorption isotherms indicated that the interaction between PHCs and modified diatomite was monolayer adsorption. The important operating factors such as TX-100 dosage, adsorbent dosage, time and temperature were optimized. With the participation of the low-cost adsorbent TX3-Db with high adsorption capacity, the recovery efficiency of the washing effluents was still up to 78.9% after three cycles. A selective adsorption mechanism, based on steric hindrance and electrostatic repulsion, was proposed to explain the removal of PHCs from washing effluents.

scholarly journals Adsorptive removal of catechol and resorcinol by orange flavedo (citrus sinensis): mechanisms based on the flavedo com-ponents d-limonene, carotenoids, ascorbates, flavonoids and hydroxycinnamic acids

2017 ◽  
Vol 6 (1) ◽  
pp. 7
Author(s):  
Kamgaing Theophile ◽  
Doungmo Giscard ◽  
Ngouoko Kouonang Jimmy Julio ◽  
Tchieno Melataguia Francis Merlin ◽  
Ketcha MBadkam Joseph
Keyword(s):  
Contact Time ◽  
Low Cost ◽  
Order Kinetic ◽  
X Ray Diffraction ◽  
Batch Mode ◽  
X Ray ◽  
Adsorbate Concentration ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Adsorption Phenomena

Orange flavedo and its adsorption behavior towards catechol (Ctc) and resorcinol (Res) were studied. Adsorption experiments were conducted in batch mode at room temperature. X-ray diffraction (XRD), Scanning electron microscopy (SEM), Energy-dispersive X-ray spectroscopy (EDX), Brunauer−Emmett−Teller (BET) and Fourier transform infrared (FTIR) data were used to characterize the biosorbent. The Effects of various parameters including equilibrium pH, sorbent dosage, initial adsorbate concentration and contact time were investigated. The optimum contact time and pH for the removal of Ctc and Res were 35 min and pH 2 respectively. The adsorption isotherms fitted well with Freundlich model, the adsorption of Ctc and Res being multilayer and the surface of orange flavedo heterogeneous; the pseudo-second order kinetic model better reflects the adsorption phenomena. An adsorption mechanism based on the molecules grafted to the surface of the orange flavedo is proposed in this study. 0.2 gram of the biosorbent was sufficient to completely eliminate 2.2 milligrams of resorcinol and catechol from solution. Therefore, non-modified orange flavedo is a promising candidate, as a low-cost biosorbent, for the removal of Ctc and Res from aqueous solution.

Adsorption studies of Cu(II) onto biopolymer chitosan and its nanocomposite 5%bentonite/chitosan

2016 ◽  
Vol 73 (9) ◽  
pp. 2199-2210 ◽  
Author(s):  
Hamou Moussout ◽  
Hammou Ahlafi ◽  
Mustapha Aazza ◽  
Omar Zegaoui ◽  
Charaf El Akili
Keyword(s):  
Adsorption Capacity ◽  
Active Sites ◽  
Batch Adsorption ◽  
X Ray Diffraction ◽  
X Ray ◽  
Monolayer Adsorption ◽  
Adsorption Processes ◽  
Pseudo Second Order ◽  
Nanocomposite Adsorbent ◽  
Kinetics Of

Chitosan (CS) and nanocomposite 5%bentonite/chitosan (5%Bt/CS) prepared from the natural biopolymer CS were tested to remove Cu(II) ions using a batch adsorption experiment at various temperatures (25, 35 and 45°C). X-ray diffraction, Fourier transform infrared spectroscopy, and thermogravimetric analysis/differential thermal analysis (TGA/DTA) were used in CS and the nanocomposite characterisation. This confirmed the exfoliation of bentonite (Bt) to form the nanocomposite. The adsorption kinetics of copper on both solids was found to follow a pseudo-second-order law at each studied temperature. The Cu(II) adsorption capacity increased as the temperature increased from 25 to 45°C for nanocomposite adsorbent but slightly increased for CS. The data were confronted to the nonlinear Langmuir, Freundlich and Redlich–Peterson models. It was found that the experimental data fitted very well the Langmuir isotherm over the whole temperature and concentration ranges. The maximum monolayer adsorption capacity for the Cu(II) was 404–422 mg/g for CS and 282–337 mg/g for 5%Bt/CS at 25–45°C. The thermodynamic study showed that the adsorption process was spontaneous and endothermic. The complexation of Cu(II) with NH2 and C = O groups as active sites was found to be the main mechanism in the adsorption processes.

Efficient adsorption of chlorpyrifos onto modified activated carbon by gamma irradiation; a plausible adsorption mechanism

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Mohamed S. Yahia ◽  
Ahmed S. Elzaref ◽  
Magdy B. Awad ◽  
Ahmed M. Tony ◽  
Ahmed S. Elfeky
Keyword(s):  
Gamma Irradiation ◽  
Area Measurement ◽  
Maximum Adsorption Capacity ◽  
X Ray Diffraction ◽  
X Ray ◽  
First Order ◽  
Pseudo Second Order ◽  
Ft Ir ◽  
Pseudo First Order ◽  
Kinetics Of

Abstract Commercial Granulated Active Carbon (GAC) has been modified using 10 Gy dose Gamma irradiation (GAC10 Gy) for increasing its ability of air purification. Both, the raw and treated samples were applied for removing Chlorpyrifos pesticide (CPF) from ambient midair. Physicochemical properties of the two materials were characterized by Fourier Transform Infrared (FT-IR) and Raman spectroscopy. The phase formation and microstructure were monitored using X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM), supported with Energy-Dispersive X-ray (EDX). The Surface area measurement was detected using BET particle size prosometry. Obtained outcomes showed that, the maximum adsorption capacity, given by Langmuir equations, was greatly increased from 172.712 to 272.480 mg/g for GAC and GAC10 Gy, respectively, with high selectivity. The overall removal efficiency of GAC10 Gy was notably comparable to that of the original GAC-sorbent. The present study indicated that, gamma irradiation could be a promising technique for treating GAC and turned it more active in eliminating the pesticides pollutants from surrounding air. The data of equilibrium has been analyzed by Langmuir and Freundlich models, that were considerably better suited for the investigated materials than other models. The process kinetics of CPF adsorbed onto both tested carbon versions were found to obey the pseudo first order at all concentrations with an exception at 70 mg/l using GAC, where, the spontaneous exothermic adsorption of Chlorpyrifos is a strong function for the pseudo-first order (PFO) and pseudo second order (PSO) kinetics.

scholarly journals The Removal of Uranium and Thorium from Their Aqueous Solutions by 8-Hydroxyquinoline Immobilized Bentonite

Minerals ◽  
2019 ◽  
Vol 9 (10) ◽  
pp. 626 ◽  
Author(s):  
Salah ◽  
Gaber ◽  
Kandil
Keyword(s):  
Aqueous Solutions ◽  
Metal Ions ◽  
Langmuir Isotherm ◽  
Freundlich Isotherm ◽  
Order Kinetic ◽  
X Ray Diffraction ◽  
Solution Ph ◽  
X Ray ◽  
Order Kinetic Model ◽  
Pseudo Second Order

The sorption of uranium and thorium from their aqueous solutions by using 8-hydroxyquinoline modified Na-bentonite (HQ-bentonite) was investigated by the batch technique. Na-bentonite and HQ-bentonite were characterized by X-ray fluorescence (XRF), X-ray diffraction (XRD), scanning electron microscopy (SEM), and Fourier Transform Infrared (FTIR) spectroscopy. Factors that influence the sorption of uranium and thorium onto HQ-bentonite such as solution pH, contact time, initial metal ions concentration, HQ-bentonite mass, and temperature were tested. Sorption experiments were expressed by Freundlich and Langmuir isotherms and the sorption results demonstrated that the sorption of uranium and thorium onto HQ-bentonite correlated better with the Langmuir isotherm than the Freundlich isotherm. Kinetics studies showed that the sorption followed the pseudo-second-order kinetic model. Thermodynamic parameters such as ΔH°, ΔS°, and ΔG° indicated that the sorption of uranium and thorium onto HQ-bentonite was endothermic, feasible, spontaneous, and physical in nature. The maximum adsorption capacities of HQ-bentonite were calculated from the Langmuir isotherm at 303 K and were found to be 63.90 and 65.44 for U(VI) and Th(IV) metal ions, respectively.

scholarly journals Synthesis Fe3O4/Talc nanocomposite by coprecipition-ultrasonication method and advances in hexavalent chromium removal from aqueous solution

2020 ◽  
Vol 38 (9-10) ◽  
pp. 483-501
Author(s):  
Nguyen Thi Huong ◽  
Nguyen Ngoc Son ◽  
Vo Hoang Phuong ◽  
Cong Tien Dung ◽  
Pham Thi Mai Huong ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Adsorption Process ◽  
Low Cost ◽  
Batch Experiments ◽  
X Ray Diffraction ◽  
Order Model ◽  
X Ray ◽  
Pseudo Second Order ◽  
Ft Ir ◽  
Langmuir And Freundlich Equations

The Fe3O4/Talc nanocomposite was synthesized by the coprecipitation-ultrasonication method. The reaction was carried out under a inert gas environment. The nanoparticles were characterized by X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), fourier-transform infrared spectroscopy (FT-IR) and vibrating sample magnetometry techniques (VSM), the surface area of the nanoparticles was determined to be 77.92 m2/g by Brunauer-Emmett-Teller method (BET). The kinetic data showed that the adsorption process fitted with the pseudo-second order model. Batch experiments were carried out to determine the adsorption kinetics and mechanisms of Cr(VI) by Fe3O4/Talc nanocomposite. The adsorption process was found to be highly pH-dependent, which made the material selectively adsorb these metals from aqueous solution. The isotherms of adsorption were also studied using Langmuir and Freundlich equations in linear forms. It is found that the Langmuir equation showed better linear correlation with the experimental data than the Freundlich. The thermodynamics of Cr(VI) adsorption onto the Fe3O4/Talc nanocomposite indicated that the adsorption was exothermic. The reusability study has proven that Fe3O4/Talc nanocomposite can be employed as a low-cost and easy to separate.

scholarly journals Removal of lead from aqueous solutions by low cost and waste biosorbents (lemon, bean and artichoke shells)

2020 ◽  
Vol 81 (1) ◽  
pp. 159-169
Author(s):  
Feyza Ergüvenerler ◽  
Şerif Targan ◽  
Vedia Nüket Tirtom
Keyword(s):  
Contact Time ◽  
Adsorption Process ◽  
Low Cost ◽  
Standard Free Energy ◽  
Freundlich Isotherm ◽  
Standard Entropy ◽  
X Ray ◽  
Adsorption Capacities ◽  
Influence Of Ph ◽  
Scanning Electron

Abstract Simple, fast, effective, low cost and waste biosorbents, lemon, bean and artichoke shells, were used to remove lead (II) ions from aqueous solution. The influence of pH, contact time, temperature and lead (II) concentration of the removal process was investigated. The sufficient contact time was deemed 10 minutes for bean and artichoke shells and 60 minutes for lemon shells for Pb(II) ions. The thermodynamic parameters, such as standard free energy (ΔG), standard enthalpy (ΔH), and standard entropy (ΔS) of the adsorption process were calculated as −5.6786, −5.5758, −3.1488 kJmol−1 for ΔG, −7.2791, −20.285, −9.5561 kJ mol−1 for ΔH, −0.00545, −0.05017, −0.02185 kJ mol−1 K−1 for ΔS, respectively, for lemon, artichoke and bean shells. Maximum adsorption capacities of lead (II) were observed as 61.30 mg g−1, 88.5 mg g−1 and 62.81 mg g−1, respectively, for lemon, bean and artichoke shells according to the Freundlich isotherm model at 20 °C. Scanning electron microscope (SEM) and energy-dispersive X-ray detector (EDX) were used to characterize the surface morphology of the adsorbents. Consequently, Pb(II) removal using lemon, bean and artichoke shells would be an effective method for the economic treatment of wastewater.

Sign in / Sign up

Export Citation Format

Share Document