Step-feed operation at short detention times – a cost effective method for improving wastewater treatment

2000 ◽  
Vol 41 (9) ◽  
pp. 15-20 ◽  
Author(s):  
R.E. Adamski ◽  
V. DeSantis ◽  
A. Spangel ◽  
J. Pynn ◽  
L. Betty ◽  
...  
Keyword(s):  
New York ◽  
Wastewater Treatment ◽  
Activated Sludge ◽  
Nitrogen Removal ◽  
Control Plant ◽  
Treatment Plant ◽  
Cost Savings ◽  
High Rate ◽  
Secondary Treatment ◽  
Activated Sludge Process

The Newtown Creek Water Pollution Control Plant (WPCP) is New York City's largest wastewater treatment plant. Wastewater treatment is provided by a high-rate activated sludge process without primary sedimentation. This process has achieved approximately 65 percent BOD5 and 75 percent TSS removal. As part of a revised facility plan, two alternative tracks were recommended for upgrading the plant to secondary treatment and providing nitrogen removal. One track would require demolishing most of the existing tankage and constructing new primary tanks followed by a step-feed biological nitrogen removal activated sludge process. The second track would preserve the existing high-rate activated sludge process and use biological filters to remove additional TSS, BOD5 and nitrogen. Alternatives have been investigated to enhance treatment at the Newtown Creek WPCP while the secondary treatment plant upgrading is being completed. This investigation demonstrated that simply converting the existing aeration tanks to step-feed operation could significantly improve TSS and BOD removals. These findings have led the City to consider a third track to meet secondary treatment requirements, (but with no nitrogen removal), consisting of modifying the existing plant to step-feed and adding additional step-feed aeration/sedimentation capacity. This track offers significant cost savings over Track 1 and Track 2.

Rehabilitation and Upgrading of the Beni Suef City Wastewater Treatment Plant

1990 ◽  
Vol 22 (7-8) ◽  
pp. 131-138
Author(s):  
Ahmed Fadel
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Wastewater Treatment Plant ◽  
Treatment Plant ◽  
Primary Treatment ◽  
High Rate ◽  
Shock Load ◽  
Economic Evaluations ◽  
Activated Sludge Process ◽  
Trickling Filter

Many of Egypt's cities have existing treatment plants under operation that have been constructed before 1970. Almost all of these treatment plants now need rehabilitation and upgrading to extend their services for a longer period. One of these plants is the Beni Suef City Wastewater Treatment Plant. The Beni Suef WWTP was constructed in 1956. It has primary treatment followed by secondary treatment employing intermediate rate trickling filters. The BOD, COD, and SS concentration levels are relatively high. They are approximately 800, 1100, and 600 mg/litre, respectively. The Beni Suef city required the determination of the level of work needed for the rehabilitation and upgrading of the existing 200 l/s plant and to extend its capacity to 440 l/s at year 2000 A description of the existing units, their deficiencies and operation problems, and the required rehabilitation are presented and discussed in this paper. Major problems facing the upgrading were the lack of space for expansion and the shortage of funds. It was, therefore, necessary to study several alternative solutions and methods of treatment. The choice of alternatives was from one of the following schemes: a) changing the filter medium, its mode of operation and increasing the number of units, b) changing the trickling filter to high rate and combining it with the activated sludge process, for operation by one of several possible combinations such as: trickling filter-solids contact, roughing filter-activated sludge, and trickling filter-activated sludge process, c) dividing the flow into two parts, the first part to be treated using the existing system and the second part to be treated by activated sludge process, and d) expanding the existing system by increasing the numbers of the different process units. The selection of the alternative was based on technical, operational and economic evaluations. The different alternatives were compared on the basis of system costs, shock load handling, treatment plant operation and predicted effluent quality. The flow schemes for the alternatives are presented. The methodology of selecting the best alternative is discussed. From the study it was concluded that the first alternative is the most reliable from the point of view of costs, handling shock load, and operation.

Operational Results of the Wolfsburg Wastewater Treatment Plant

1992 ◽  
Vol 25 (4-5) ◽  
pp. 203-209 ◽  
Author(s):  
R. Kayser ◽  
G. Stobbe ◽  
M. Werner
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Nitrogen Content ◽  
Total Nitrogen ◽  
Nitrogen Removal ◽  
Wastewater Treatment Plant ◽  
Treatment Plant ◽  
Phosphate Removal ◽  
Total Nitrogen Content ◽  
Activated Sludge Process

At Wolfsburg for a load of 100,000 p.e., the step-feed activated sludge process for nitrogen removal is successfully in operation. Due to the high denitrification potential (BOD:TKN = 5:1) the effluent total nitrogen content can be kept below 10 mg l−1 N; furthermore by some enhanced biological phosphate removal about 80% phosphorus may be removed without any chemicals.

DESIGN PLANNING WASTEWATER TREATMENT PLANT OF NATA DE COCO INDUSTRY WITH THE ACTIVATED SLUDGE PROCESS

2016 ◽  
Vol 9 (2) ◽  
Author(s):  
Dinda Rita K. Hartaja ◽  
Imam Setiadi
Keyword(s):  
Waste Water ◽  
Wastewater Treatment ◽  
Activated Sludge ◽  
Waste Water Treatment ◽  
Treatment Plant ◽  
Water Treatment Plant ◽  
Appropriate Technology ◽  
Waste Water Treatment Plant ◽  
Activated Sludge Process ◽  
High Level

Generally, wastewater of nata de coco industry contains suspended solids and COD were high, ranging from 90,000 mg / l. The high level of of the wastewater pollutants, resulting in nata de coco industry can not be directly disposed of its wastewater into the environment agency. Appropriate technology required in order to process the waste water so that the treated water can meet the environmental quality standards that are allowed. Designing the waste water treatment plant that is suitable and efficient for treating industrial wastewater nata de coco is the activated sludge process. Wastewater treatment using activated sludge process of conventional (standard) generally consists of initial sedimentation, aeration and final sedimentation.Keywords : Activated Sludge, Design, IPAL

High rate and compact single sludge pre-denitrification process for retrofit

1994 ◽  
Vol 30 (6) ◽  
pp. 31-40 ◽  
Author(s):  
Hiroyshi Emori ◽  
Hiroki Nakamura ◽  
Tatsuo Sumino ◽  
Tadashi Takeshima ◽  
Katsuzo Motegi ◽  
...  
Keyword(s):  
Activated Sludge ◽  
Sewage Treatment ◽  
Treatment Plant ◽  
High Rate ◽  
Activated Sludge Process ◽  
Nitrogen And Phosphorus ◽  
Conventional Activated Sludge ◽  
Treatment Techniques ◽  
Conventional Activated Sludge Process ◽  
Denitrification Process

For the sewage treatment plants near rivers and closed water bodies in urbanized areas in Japan and European countries, there is a growing demand for introduction of advanced treatment processes for nitrogen and phosphorus from the viewpoints of water quality conservation and environmental protection. In order to remove nitrogen by the conventional biological treatment techniques, it is necessary to make a substantial expansion of the facility as compared with the conventional activated sludge process. In such urbanized districts, it is difficult to secure a site and much capital is required to expand the existing treatment plant. To solve these problems, a compact single sludge pre-denitrification process using immobilized nitrifiers was developed. Dosing the pellets, which are suitable for nitrifiers growth and physically durable, into the nitrification tank of single sludge pre-denitrification process made it possible to perform simultaneous removal of BOD and nitrogen in a retention time equal to that in the conventional activated sludge process even at the low water temperature of about 10 °C. The 3,000 m3/d full-scale conventional activated sludge plant was retrofitted and has been successfully operated.

Automatic control for DO and pH in the activated sludge process in a coke wastewater treatment plant

1998 ◽  
Vol 37 (12) ◽  
pp. 141-148 ◽  
Author(s):  
B. K. Lee ◽  
S. W. Sung ◽  
H. D. Chun ◽  
J. K. Koo
Keyword(s):  
Wastewater Treatment ◽  
Control System ◽  
Activated Sludge ◽  
Automatic Control ◽  
Wastewater Treatment Plant ◽  
Treatment Plant ◽  
Pi Controller ◽  
Activated Sludge Process ◽  
Set Point ◽  
Coke Wastewater

The objective of this study is to develop an automatic control system for dissolved oxygen (DO) and pH of the activated sludge process in a coke wastewater treatment plant. A discrete type autotuned proportional-integral (PI) controller using an auto-regressive exogenous (ARX) model as a process model was developed to maintain the DO concentration in aerators by controlling the speed of surface aerators. Also a nonlinear pH controller using the titration curve was used to control the pH of influent wastewater. This control system was tested in a pilot scale plant. During this pilot plant experiment, there was small deviation of pH and the electric power consumption of surface aerators was reduced up to 70% with respect to the full operation when the DO set point was 2 mg/l. For real plant operation with this system, the discrete PI controller showed good tracking for set point change. The electricity saving was more than 40% of the electricity consumption when considering surface aerators. As a result of maintaining the DO constantly at the set point by the automatic control system, the fluctuation of effluent quality was decreased and overall improvement of the effluent water quality was achieved.

Enhancing nitrogen removal efficiency in a dyestuff wastewater treatment plant with the IFFAS process: the pilot-scale and full-scale studies

2017 ◽  
Vol 77 (1) ◽  
pp. 70-78 ◽  
Author(s):  
Yanjun Mao ◽  
Xie Quan ◽  
Huimin Zhao ◽  
Yaobin Zhang ◽  
Shuo Chen ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Removal Efficiency ◽  
Nitrogen Removal ◽  
Treatment Plant ◽  
Oxygen Demand ◽  
Pilot Scale ◽  
Full Scale ◽  
Nitrification And Denitrification ◽  
Dyestuff Wastewater

Abstract The activated sludge (AS) process is widely applied in dyestuff wastewater treatment plants (WWTPs); however, the nitrogen removal efficiency is relatively low and the effluent does not meet the indirect discharge standards before being discharged into the industrial park's WWTP. Hence it is necessary to upgrade the WWTP with more advanced technologies. Moving bed biofilm processes with suspended carriers in an aerobic tank are promising methods due to enhanced nitrification and denitrification. Herein, a pilot-scale integrated free-floating biofilm and activated sludge (IFFAS) process was employed to investigate the feasibility of enhancing nitrogen removal efficiency at different hydraulic retention times (HRTs). The results showed that the effluent chemical oxygen demand (COD), ammonium nitrate (NH4+-N) and total nitrogen (TN) concentrations of the IFFAS process were significantly lower than those of the AS process, and could meet the indirect discharge standards. PCR-DGGE and FISH results indicated that more nitrifiers and denitrifiers co-existed in the IFFAS system, promoting simultaneous nitrification and denitrification. Based on the pilot results, the IFFAS process was used to upgrade the full-scale AS process, and the effluent COD, NH4+-N and TN of the IFFAS process were 91–291 mg/L, 10.6–28.7 mg/L and 18.9–48.6 mg/L, stably meeting the indirect discharge standards and demonstrating the advantages of IFFAS in dyestuff wastewater treatment.

OPTIMIZING OPERATION OF WASTEWATER TREATMENT PLANTS BY OFFLINE AND ONLINE COMPUTER SIMULATION

1994 ◽  
Vol 30 (2) ◽  
pp. 165-174 ◽  
Author(s):  
Ralf Otterpohl ◽  
Thomas Rolfs ◽  
Jörg Londong
Keyword(s):  
Computer Simulation ◽  
Wastewater Treatment ◽  
Activated Sludge ◽  
Nitrogen Removal ◽  
Wastewater Treatment Plants ◽  
Treatment Plant ◽  
Historical Analysis ◽  
Computer Work ◽  
Biological Phosphorus Removal ◽  
Wide Range

Computer simulation of activated sludge plant for nitrogen removal has become a reliable tool to predict the behaviour of the plant Models including biological phosphorus removal still require some practical experience but they should be available soon. This will offer an even wider range than today's work with nitrogen removal. One major benefit of computer simulation of wastewater treatment plants (WTP) is the optimization of operation. This can be done offline if hydrographs of a plant are collected and computer work is done with “historical” analysis. With online simulation the system is fed with hydrographs up to the actual time. Prognosis can be done from the moment of the computer work based on usual hydrographs. The work of the authors shows how accuratly a treatment plant can be described, when many parameters are measured and available as hydrographs. A very careful description of all details of the special plant is essential, requiring a flexible simulation tool. Based on the accurate simulation a wide range of operational decisions can be evaluated. It was possible to demonstrate that the overall efficiency in nitrogen removal and energy consumption of ml activated sludge plant can be improved.

Suspended carrier technology allows upgrading high-rate activated sludge plants for nitrogen removal via process intensification

2000 ◽  
Vol 41 (4-5) ◽  
pp. 5-12 ◽  
Author(s):  
E.v. Münch ◽  
K. Barr ◽  
S. Watts ◽  
J. Keller
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Residence Time ◽  
Nitrogen Removal ◽  
Wastewater Treatment Plant ◽  
Pilot Plant ◽  
Treatment Plant ◽  
Carbon Removal ◽  
Suspended Carrier ◽  
Plastic Media

The Oxley Creek wastewater treatment plant is a conventional 185,000 EP BOD removal activated sludge plant that is to be upgraded for nitrogen removal to protect its receiving water bodies, the Brisbane River and Moreton Bay. Suspended carrier technology is one possible way of upgrading this activated sludge wastewater treatment plant for nitrogen removal. Freely moving plastic media is added to the aeration zone, providing a growth platform for nitrifying bacteria and increasing the effective solids residence time (SRT). This paper presents the results from operating a pilot plant for 7 months at the Oxley Creek WWTP in Brisbane, Australia. Natrix Major 12/12 plastic media, developed by ANOX (Lund, Sweden), was trialed in the pilot plant. The pilot plant was operated with a mixed liquor suspended solids concentration of 1220 mg/L and a total hydraulic residence time of 5.4 hours, similar to the operating conditions in the full-scale Stage 1&2 works at the Oxley Creek WWTP. The plastic carriers were suspended in the last third of the bioreactor volume, which was aerated to a DO setpoint of 4.0 mg/L. The first third of the bioreactor volume was made anoxic and the second third served for carbon removal, being aerated to a DO setpoint of 0.5 mg/L. The results from the pilot plant indicate that an average effluent total inorganic nitrogen concentration (ammonia-N plus NOx−N) of less than 12 mg/L is possible. However, the effluent ammonia concentrations from the pilot plant showed large weekly fluctuations due to the intermittent operation of the sludge dewatering centrifuge returning significant ammonia loads to the plant on three days of the week. Optimising denitrification was carried out by lowering the DO concentration in the influent and in the carbon removal reactor. The results from the pilot plant study show that the Oxley Creek WWTP could be upgraded for nitrogen removal without additional tankage, using suspended carrier technology.

Sign in / Sign up

Export Citation Format

Share Document