Adsorption properties of cationic rhodamine B dye onto metals chloride-activated castor bean residue carbons

2016 ◽  
Vol 75 (4) ◽  
pp. 864-880 ◽  
Author(s):  
Lee Lin Zhi ◽  
Muhammad Abbas Ahmad Zaini
Keyword(s):  
Rhodamine B ◽  
Castor Bean ◽  
Activated Carbons ◽  
Chemical Activation ◽  
Textural Properties ◽  
Rate Limiting Step ◽  
Adsorption Data ◽  
Pseudo Second Order ◽  
Enthalpy And Entropy ◽  
Rate Limiting

This work was aimed to evaluate the feasibility of castor bean residue based activated carbons prepared through metals chloride activation. The activated carbons were characterized for textural properties and surface chemistry, and the adsorption data of rhodamine B were established to investigate the removal performance. Zinc chloride-activated carbon with specific surface area of 395 m2/g displayed a higher adsorption capacity of 175 mg/g. Magnesium chloride and iron(III) chloride are less toxic and promising agents for composite chemical activation. The adsorption data obeyed Langmuir isotherm and pseudo-second-order kinetics model. The rate-limiting step in the adsorption of rhodamine B is film diffusion. The positive values of enthalpy and entropy indicate that the adsorption is endothermic and spontaneous at high temperature.

Biochars prepared from rabbit manure for the adsorption of rhodamine B and Congo red: characterisation, kinetics, isotherms and thermodynamic studies

2020 ◽  
Vol 81 (3) ◽  
pp. 436-444
Author(s):  
Wen Huang ◽  
Min Zhang ◽  
Yinhai Wang ◽  
Jiao Chen ◽  
Jianqiang Zhang
Keyword(s):  
Rhodamine B ◽  
Congo Red ◽  
Molecular Layer ◽  
Suitable Model ◽  
Related Factors ◽  
Adsorption Sites ◽  
Rate Limiting Step ◽  
Layer Adsorption ◽  
Pseudo Second Order ◽  
Rate Limiting

Abstract Biochar was prepared from rabbit faeces (RFB550) at 550 °C through pyrolysis and was characterised using elemental analysis, scanning electron microscopy, Brunauer–Emmett–Teller analysis and Fourier transform infrared spectroscopy (FTIR). The related factors, kinetics, isothermal curves and thermodynamics of the adsorption behaviours were investigated by conducting batch experiments. The results revealed the adsorption equilibrium of rhodamine B (RhB) and Congo red (CR) onto RFB550 with initial concentrations of 30 mg · L−1 at 25 °C and 210 min, and the best adsorption was observed when the pH of the RhB and CR solutions was 3 and 5, respectively. Pseudo-second-order kinetics was the most suitable model for describing the adsorption of RhB and CR onto RFB550, indicating that the rate-limiting step was mainly chemical adsorption. The isotherm data were best described by the Freundlich model, and the adsorption process was multi-molecular layer adsorption. Thermodynamic parameters revealed the spontaneous adsorption of RhB and CR onto RFB550. According to the results of the FTIR analysis, the oxygen-containing functional groups and aromatic structures on the surface of RFB550 provided abundant adsorption sites for RhB and CR, and the adsorption mechanism was potentially related to the hydrogen bonds and π–π bonds.

Removal of Mg from spring water using natural clinoptilolite

Clay Minerals ◽  
2012 ◽  
Vol 47 (1) ◽  
pp. 81-92 ◽  
Author(s):  
S. Tomić ◽  
N. Rajić ◽  
J. Hrenović ◽  
D. Povrenović
Keyword(s):  
Ion Exchange ◽  
Kinetic Studies ◽  
Spring Water ◽  
Zeolite A ◽  
Zeolitic Tuff ◽  
Rate Limiting Step ◽  
Intra Particle Diffusion ◽  
Pseudo Second Order ◽  
Natural Clinoptilolite ◽  
Rate Limiting

AbstractNatural zeolitic tuff from Brus (Serbia) consisting mostly of clinoptilolite (about 90%) has been investigated for the reduction of the Mg concentration in spring water. The sorption capacity of the zeolite is relatively low (about 2.5 mg Mg g-1for the initial concentration of 100 mg Mg dm-3). The zeolitic tuff removes Mg from water solutions by ion exchange, which has been demonstrated by energy dispersive X-ray analysis (EDS). The extent of ion exchange was influenced by the pH and the initial Mg concentration. Kinetic studies revealed that Lagergen's pseudo-second order model was followed. Intra-particle diffusion of Mg2+influenced the ion exchange, but it is not the rate-limiting step. Rather than having to dispose of the Mg-loaded (waste) zeolite, a possible application was tested. Addition to a wastewater with a low concentration of Mg showed that it could successfully make up for the lack of Mg micronutrient and, accordingly, enabled the growth of phosphate-accumulating bacteriaA. Junii, increasing the amount of phosphate removed from the wastewater.

scholarly journals Comparative studies on the removal of copper (II) by Ulva fasciata activated carbon and commercially activated carbon

2012 ◽  
Vol 14 (4) ◽  
pp. 88-94 ◽  
Author(s):  
R.P. Suresh Jeyakumar ◽  
V. Chandrasekaran
Keyword(s):  
Activated Carbon ◽  
Activated Carbons ◽  
Synthetic Wastewater ◽  
Batch Adsorption ◽  
First Order ◽  
Ulva Fasciata ◽  
Adsorption Data ◽  
Pseudo Second Order ◽  
Pseudo First Order ◽  
Adsorbent Dose

Abstract In this work, the efficiency of Ulva fasciata sp. activated carbons (CCUC, SCUC and SSUC) and commercially activated carbon (CAC) were studied for the removal of Cu (II) ions from synthetic wastewater. Batch adsorption experiments were carried out as a function of pH, contact time, initial copper concentration and adsorbent dose. The percentage adsorption of copper by CCUC, SSUC, SCUC and CAC are 88.47%, 97.53%, 95.78% and 77.42% respectively. Adsorption data were fitted with the Langmuir, Freundlich and Temkin models. Two kinetic models pseudo first order and the pseudo second order were selected to interpret the adsorption data.

scholarly journals Pinecone-Derived Activated Carbons as an Effective Medium for Hydrogen Storage

Energies ◽  
2020 ◽  
Vol 13 (9) ◽  
pp. 2237
Author(s):  
Sara Stelitano ◽  
Giuseppe Conte ◽  
Alfonso Policicchio ◽  
Alfredo Aloise ◽  
Giovanni Desiderio ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Hydrogen Storage ◽  
Adsorption Capacity ◽  
Surface Area ◽  
Hydrogen Adsorption ◽  
Activated Carbons ◽  
Chemical Activation ◽  
Textural Properties ◽  
Biomass Waste ◽  
Wavelength Dispersive Spectrometry

Pinecones, a common biomass waste, has an interesting composition in terms of cellulose and lignine content that makes them excellent precursors in various activated carbon production processes. The synthesized, nanostructured, activated carbon materials show textural properties, a high specific surface area, and a large volume of micropores, which are all features that make them suitable for various applications ranging from the purification of water to energy storage. Amongst them, a very interesting application is hydrogen storage. For this purpose, activated carbon from pinecones were prepared using chemical activation with different KOH/precursor ratios, and their hydrogen adsorption capacity was evaluated at liquid nitrogen temperatures (77 K) at pressures of up to 80 bar using a Sievert’s type volumetric apparatus. Regarding the comprehensive characterization of the samples’ textural properties, the measurement of the surface area was carried out using the Brunauer–Emmett–Teller method, the chemical composition was investigated using wavelength-dispersive spectrometry, and the topography and long-range order was estimated using scanning electron microscopy and X-ray diffraction, respectively. The hydrogen adsorption properties of the activated carbon samples were measured and then fitted using the Langmuir/ Töth isotherm model to estimate the adsorption capacity at higher pressures. The results showed that chemical activation induced the formation of an optimal pore size distribution for hydrogen adsorption centered at about 0.5 nm and the proportion of micropore volume was higher than 50%, which resulted in an adsorption capacity of 5.5 wt% at 77 K and 80 bar; this was an increase of as much as 150% relative to the one predicted by the Chahine rule.

scholarly journals Tailored activated carbons for supercapacitors derived from hydrothermally carbonized sugars by chemical activation

RSC Advances ◽  
2016 ◽  
Vol 6 (112) ◽  
pp. 110629-110641 ◽  
Author(s):  
Kian Keat Lee ◽  
Wenming Hao ◽  
Mikaela Gustafsson ◽  
Cheuk-Wai Tai ◽  
Daniel Morin ◽  
...  
Keyword(s):  
Activated Carbons ◽  
Chemical Activation ◽  
Textural Properties

“Sugar”-supercapacitors: analyses of textural properties revealed that the specific capacitances for glucose derived-activated carbons correlated most strongly with ultramicropores.

scholarly journals Removal of Paracetamol from Wastewater by Calcined Gypsum: Adsorption and Kinetics Study

2020 ◽  
Vol 3 (1) ◽  
pp. 11-18
Author(s):  
Hossam Al-Itawi
Keyword(s):  
Aqueous Solutions ◽  
Minor Effect ◽  
Recrystallization Process ◽  
Rate Limiting Step ◽  
Pseudo Second Order ◽  
Calcined Gypsum ◽  
A Minor ◽  
Two Stages ◽  
Rate Limiting ◽  
Best Fit

It has been established that the presence of paracetamol in wastewaters can cause a potential risk to the environment. This work examined the possibility of using calcined gypsum in removing paracetamol from aqueous solutions. At neutral pH conditions, calcined gypsum was successful in removing paracetamol via adsorption, from aqueous solutions with a removal efficiency that ranged between 56.8 to 65.3 % of an initial concentration of 600 ppm. Increased temperature (from 20 to 500C) had a minor effect on the removal % of paracetamol while increasing the initial calcined gypsum dose (from 0.5 gm to 3 gm) and contact time (up to 15 min) increased by the removal % of paracetamol. Thermodynamically, the adsorption of paracetamol by calcined gypsum process was found to be spontaneous and endothermic, and more likely a physical process, while kinetically; the Pseudo-Second order model was found to be the best fit compared to the Elovich model. The removal process mainly consists of two stages, and it could be deduced from the kinetic behavior of paracetamol adsorption that the recrystallization process can be another rate-limiting step in the process.

scholarly journals Chlorates(VII) removal on Dowex™PSR-2 resin

2016 ◽  
Vol 71 (1) ◽  
pp. 105
Author(s):  
Dorota Kołodyńska ◽  
Aleksandra Łyko ◽  
Marzena Gęca ◽  
Zbigniew Hubicki
Keyword(s):  
Solution Concentration ◽  
Intraparticle Diffusion ◽  
Optimum Conditions ◽  
Order Model ◽  
Experimental Conditions ◽  
Freundlich Model ◽  
Rate Limiting Step ◽  
Limiting Step ◽  
Pseudo Second Order ◽  
Rate Limiting

<p>Lately there has been observed the increased presence of chlorates(VII) in the natural environment which can affect human health negatively. Therefore the removal of chlorate(VII) ions using the gel type resin functionalized with the tri-n-butyl ammonium (Dowex<sup>™</sup>PSR-2) from waters was studied. The main aim was to evaluate the effects of experimental conditions including contact time, initial solution concentration, pH and temperature on chlorate(VII) ions removal as well as the anion exchanger properties on chlorate(VII) ions sorption. It was found that only the pseudo second order model described the experimental data well and the intraparticle diffusion was not the rate-limiting step. According to the Freundlich model, the q<sub>e</sub> value was to be 69.26 mg/g at optimum conditions (pH 7.0 at 25 <sup>o</sup>C).<strong></strong></p>

scholarly journals CO2 and CH4 Adsorption Behavior of Biomass-Based Activated Carbons

Energies ◽  
2018 ◽  
Vol 11 (11) ◽  
pp. 3136 ◽  
Author(s):  
Deneb Peredo-Mancilla ◽  
Imen Ghouma ◽  
Cecile Hort ◽  
Camelia Matei Ghimbeu ◽  
Mejdi Jeguirim ◽  
...  
Keyword(s):  
Carbon Dioxide ◽  
Activated Carbon ◽  
Adsorption Capacity ◽  
Gas Adsorption ◽  
Activated Carbons ◽  
Chemical Activation ◽  
Textural Properties ◽  
Micropore Volume ◽  
Activation Method ◽  
Physical Activation

The aim of the present work is to study the effect of different activation methods for the production of a biomass-based activated carbon on the CO 2 and CH 4 adsorption. The influence of the activation method on the adsorption uptake was studied using three activated carbons obtained by different activation methods (H 3 PO 4 chemical activation and H 2 O and CO 2 physical activation) of olive stones. Methane and carbon dioxide pure gas adsorption experiments were carried out at two working temperatures (303.15 and 323.15 K). The influence of the activation method on the adsorption uptake was studied in terms of both textural properties and surface chemistry. For the three adsorbents, the CO 2 adsorption was more important than that of CH 4 . The chemically-activated carbon presented a higher specific surface area and micropore volume, which led to a higher adsorption capacity of both CO 2 and CH 4 . For methane adsorption, the presence of mesopores facilitated the diffusion of the gas molecules into the micropores. In the case of carbon dioxide adsorption, the presence of more oxygen groups on the water vapor-activated carbon enhanced its adsorption capacity.

Irradiated Water-activated Waste Tyre Powder for Decolourization of Reactive Orange 16

2014 ◽  
Vol 68 (1) ◽  
Author(s):  
Muhammad Abbas Ahmad Zaini ◽  
Lily Wong Chai Li ◽  
Mohd. Johari Kamaruddin ◽  
Siti Hamidah Mohd. Setapar ◽  
Mohd. Azizi Che Yunus
Keyword(s):  
Surface Area ◽  
Calcium Chloride ◽  
Activated Carbons ◽  
Chemical Activation ◽  
Water Environment ◽  
Reactive Orange 16 ◽  
Monolayer Adsorption ◽  
Pseudo Second Order ◽  
Waste Tyre ◽  
Reactive Orange

The present study was aimed to characterize the adsorptive properties of waste tyre powder based activated carbons for decolourization of reactive orange 16 (RO16). Waste tyre powder was activated through irradiated water environment (MAC). Comparison was made by conventional chemical activation using calcium chloride (CAC) and recovered calcium chloride from the first activation (RAC). Activated carbons were characterized according to surface area, morphology and functional groups. The values of surface area were recorded as 95.9, 111, 80.9m2/g for MAC, CAC and RAC, respectively. The decolourization of RO16 was observed to have the following order: MAC>CAC>RAC. Adsorption data for all activated carbons studied obeyed Langmuir isotherm for which the process could be described as monolayer adsorption. The kinetics data were well-fitted to pseudo-second-order model, suggesting the chemisorption process. 

scholarly journals Evaluation of Pb (II) Removal from Water Using Sodium Alginate/Hydroxypropyl Cellulose Beads

2020 ◽  
Vol 148 ◽  
pp. 02002 ◽  
Author(s):  
Rodel Guerrero ◽  
Catherine Acibar ◽  
Christine Marie Alarde ◽  
Jane Maslog ◽  
Christine Joy Pacilan
Keyword(s):  
Adsorption Capacity ◽  
Sodium Alginate ◽  
Contact Time ◽  
Hydroxypropyl Cellulose ◽  
Order Kinetic ◽  
Hydrogel Beads ◽  
Rate Limiting Step ◽  
Pseudo Second Order ◽  
Rate Limiting ◽  
Adsorption Kinetic Model

This study examined the removal of Pb2+ ions from aqueous solution with two different lead concentrations using a hydrogel-forming polymer based on hydroxypropyl cellulose (HPC) and sodium alginate (SA). The feasibility of the adsorption behavior of SA/HPC beads has been investigated with three varying ratios of 50:50, 75:25 and 100:0 under a stir condition. The adsorption experiments were done to determine the effects of contact time, lead concentration and SA-HPC ratio to the adsorption capacity of SA-HPC hydrogel beads. The results showed that the ratio 75:25 showed higher adsorption capacity compared to 100:0 and 50:50. It showcased 47.72 mg/g adsorption capacity and 95.45% adsorption percentage after three hours of contact time. The adsorption kinetic model indicated that the adsorption of Pb2+ ions onto the beads followed a pseudo-second order kinetic equation. This means that the adsorption mechanism shows a chemisorption process and its sole rate-limiting step is intraparticle diffusion.

Sign in / Sign up

Export Citation Format

Share Document