Preparation of Curcumin Hydrogel Beads for the Development of Functional Kulfi, a Tailoring Delivery System

Curcumin has been demonstrated to have biological activities and its fortification in food products is an important strategy to deliver bioactive ingredients at target sites. However, studies have documented a curcumin low bioavailability and low intake. Hence, combining functional ingredients with food should be needed to prevent widespread nutrient intake shortfalls and associated deficiencies. Thus, curcumin was encapsulated in calcium-alginate and their characteristics as well as in vitro release behavior of curcumin hydrogel beads (CHBs) was studied. Moreover, CHBs were fortified in development of functional Kulfi and their quality characteristics were studied. The encapsulation efficiency was up to 95.04%, indicating that most of the curcumin was entrapped. FTIR shifts in the bands were due to the replacement of sodium ions to the calcium ions. In vitro release (%) for CHBs was found to be 67.15% after 2 h, which increased slightly up to 67.88% after 4 h. The average swelling index of CHBs was found to be 10.21 to 37.92 from 2 to 12 h in PBS (pH 7.40). Control and Kulfi fortified with CHBs showed no significant difference (p > 0.05) in colour (L = 73.03 and 75.88) and the melting rate (0.88 mL/min and 0.63 mL/min), respectively. Standard plate count was reduced in the Kulfi fortified with CHBs (13.77 × 104 CFU/mL) with high sensory score for overall acceptability (8.56) compared to the control (154.70 × 104 CFU/mL). These findings suggested the feasibility of developing CHBs to mask the bitterness, enhance the solubility, and increase the bioavailability in gastrointestinal conditions. Additionally, Kulfi could be a suitable dairy delivery system for curcumin bioactive compounds.

Nanostructured-lipid carriers-Chitosan hydrogel beads carrier system for loading of resveratrol: A new method of topical application

The aim of this study was to develop nanostructured-lipid carriers (NLC) encapsulated by Chitosan hydrogel beads for the efficient topical carrier. Dynamic light scattering (DLS), X-ray diffraction (XRD), Differential scanning calorimetry (DSC), and attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR) were conducted to study the influence of the encapsulation on the characteristic of resveratrol-loaded NLC, and the results showed that there was no impact on resveratrol-loaded NLC. Chitosan hydrogel beads could significantly improve the physical stability of resveratrol-loaded NLC. In vitro release study revealed that resveratrol-loaded NLC-Chitosan hydrogel beads had a more significant sustained-release effect on resveratrol. In vitro transdermal studies suggested that the skin permeation of resveratrol was promoted by the effect of Chitosan hydrogel beads and increased resveratrol distribution in the skin. In vitro cytotoxicity showed that resveratrol-loaded NLC-Chitosan hydrogel beads did not exert a hazardous effect on L929 cells. Hence, NLC-Chitosan hydrogel beads might be a promising method for topical applications of resveratrol.

Tuning Alginate Microparticle Size via Atomization of Non-Newtonian Fluids

A new approach based on the atomization of non-Newtonian fluids has been proposed to produce microparticles for a potential inhalation route. In particular, different solutions of alginate were atomized on baths of different crosslinkers, piperazine and barium chloride, obtaining microparticles around 5 and 40 microns, respectively. These results were explained as a consequence of the different viscoelastic properties, since oscillatory analysis indicated that the formed hydrogel beads with barium chloride had a higher storage modulus (1000 Pa) than the piperazine ones (20 Pa). Pressure ratio (polymer solution-air) was identified as a key factor, and it should be from 0.85 to 1.00 to ensure a successful atomization, obtaining the smallest particle size at intermediate pressures. Finally, a numerical study based on dimensionless numbers was performed to predict particle size depending on the conditions. These results highlight that it is possible to control the microparticles size by modifying either the viscoelasticity of the hydrogel or the experimental conditions of atomization. Some experimental conditions (using piperazine) reduce the particle size up to 5 microns and therefore allow their use by aerosol inhalation.